Cable car (railway)

This article is about ground-based mass transit. For other cable railway systems, see Cable railway. For other uses, see Cable car.

A cable car (usually known as a cable tram outside North America) is a type of cable railway used for mass transit in which rail cars are hauled by a continuously moving cable running at a constant speed. Individual cars stop and start by releasing and gripping this cable as required. Cable cars are distinct from funiculars, where the cars are permanently attached to the cable.

A San Francisco cable car on the Powell & Hyde line

View from a cable car in San Francisco

History

 

Winding drums on the London and Blackwall cable-operated railway, 1840

 

Cable Driving Plant, Designed and Constructed by Poole & Hunt, Baltimore, MD. Drawing by P.F. Goist, circa 1882. The powerhouse has two horizontal single-cylinder engines. The lithograph shows a hypothetical prototype of a cable powerhouse, rather than any actual built structure.^[1] Poole & Hunt, machinists and engineers, was a major cable industry designer and contractor and manufacturer of gearing, sheaves, shafting and wire rope drums. They did work for cable railways in Baltimore, Chicago, Hoboken, Kansas City, New York, and Philadelphia.^[2]

The first cable-operated railway, employing a moving rope that could be picked up or released by a grip on the cars was the Fawdon Wagonway in 1826, a colliery railway line.^[3][4] The London and Blackwall Railway, which opened for passengers in east London, England, in 1840 used such a system.^[5] The rope available at the time proved too susceptible to wear and the system was abandoned in favour of steam locomotives after eight years. In America, the first cable car installation in operation probably was the West Side and Yonkers Patent Railway in New York City, as its first-ever elevated railway which ran from 1 July 1868 to 1870. The cable technology used in this elevated railway involved collar-equipped cables and claw-equipped cars, proving cumbersome. The line was closed and rebuilt, reopening with steam locomotives.

In 1869 P. G. T. Beauregard demonstrated a cable car at New Orleans^[6][7][8] and was issued U.S. patent 97,343.

Other cable cars to use grips were those of the Clay Street Hill Railroad, which later became part of the San Francisco cable car system. The building of this line was promoted by Andrew Smith Hallidie with design work by William Eppelsheimer, and it was first tested in 1873. The success of these grips ensured that this line became the model for other cable car transit systems, and this model is often known as the Hallidie Cable Car.

In 1881 the Dunedin cable tramway system opened in Dunedin, New Zealand and became the first such system outside San Francisco. For Dunedin, George Smith Duncan further developed the Hallidie model, introducing the pull curve and the slot brake; the former was a way to pull cars through a curve, since Dunedin's curves were too sharp to allow coasting, while the latter forced a wedge down into the cable slot to stop the car. Both of these innovations were generally adopted by other cities, including San Francisco.

In Australia, the Melbourne cable tramway system operated from 1885 to 1940. It was one of the most extensive in the world with 1200 trams and trailers operating over 15 routes with 103 km (64 miles) of track. Sydney also had a couple of cable tram routes.

Cable cars rapidly spread to other cities, although the major attraction for most was the ability to displace horsecar (or mule-drawn) systems rather than the ability to climb hills. Many people at the time viewed horse-drawn transit as unnecessarily cruel, and the fact that a typical horse could work only four or five hours per day necessitated the maintenance of large stables of draft animals that had to be fed, housed, groomed, medicated and rested. Thus, for a period, economics worked in favour of cable cars even in relatively flat cities.

For example, the Chicago City Railway, also designed by Eppelsheimer, opened in Chicago in 1882 and went on to become the largest and most profitable cable car system. As with many cities, the problem in flat Chicago was not one of incline, but of transportation capacity. This caused a different approach to the combination of grip car and trailer. Rather than using a grip car and single trailer, as many cities did, or combining the grip and trailer into a single car, like San Francisco's California Cars, Chicago used grip cars to pull trains of up to three trailers.

In 1883 the New York and Brooklyn Bridge Railway was opened, which had a most curious feature: though it was a cable car system, it used steam locomotives to get the cars into and out of the terminals. After 1896 the system was changed to one on which a motor car was added to each train to maneuver at the terminals, while en route, the trains were still propelled by the cable.

 

A San Francisco cable car travels along California Street in the city's Financial District.

On 25 September 1883, a test of a cable car system was held by Liverpool Tramways Company in Kirkdale, Liverpool. This would have been the first cable car system in Europe, but the company decided against implementing it. Instead, the distinction went to the 1884 Highgate Hill Cable Tramway, a route from Archway to Highgate, north London, which used a continuous cable and grip system on the 1 in 11 (9%) climb of Highgate Hill. The installation was not reliable and was replaced by electric traction in 1909.^[9] Other cable car systems were implemented in Europe, though, among which was the Glasgow District Subway, the first underground cable car system, in 1896. (London, England's first deep-level tube railway, the City & South London Railway, had earlier also been built for cable haulage but had been converted to electric traction before opening in 1890.) A few more cable car systems were built in the United Kingdom, Portugal, and France. European cities, having many more curves in their streets, were ultimately less suitable for cable cars than American cities.

Though some new cable car systems were still being built, by 1890 the cheaper to construct and simpler to operate electrically-powered trolley or tram started to become the norm, and eventually started to replace existing cable car systems. For a while hybrid cable/electric systems operated, for example in Chicago where electric cars had to be pulled by grip cars through the loop area, due to the lack of trolley wires there. Eventually, San Francisco became the only street-running manually operated system to survive—Dunedin, the second city with such cars, was also the second-last city to operate them, closing down in 1957.

Recent revival

In the last decades of the 20th-century, cable traction in general has seen a limited revival as automatic people movers, used in resort areas, airports (for example, Toronto Airport), huge hospital centers and some urban settings. While many of these systems involve cars permanently attached to the cable, the Minimetro system from Poma/Leitner Group and the Cable Liner system from DCC Doppelmayr Cable Car both have variants that allow the cars to be automatically decoupled from the cable under computer control, and can thus be considered a modern interpretation of the cable car.

Operation

 

Machinery driving the San Francisco cable car system

 

The cable slot lies centered between the two rails of the track, providing an ingress for the grip, 1970.

The cable is itself powered by a stationary engine or motor situated in a cable house or power house. The speed at which it moves is relatively constant depending on the number of units gripping the cable at any given time.

The cable car begins moving when a clamping device attached to the car, called a grip, applies pressure to ("grip") the moving cable. Conversely, the car is stopped by releasing pressure on the cable (with or without completely detaching) and applying the brakes. This gripping and releasing action may be manual, as was the case in all early cable car systems, or automatic, as is the case in some recent cable operated people mover type systems. Gripping must be applied evenly and gradually in order to avoid bringing the car to cable speed too quickly and unacceptably jarring passengers.

In the case of manual systems, the grip resembles a very large pair of pliers, and considerable strength and skill are required to operate the car. As many early cable car operators discovered the hard way, if the grip is not applied properly, it can damage the cable, or even worse, become entangled in the cable. In the latter case, the cable car may not be able to stop and can wreak havoc along its route until the cable house realizes the mishap and halts the cable.^[10]

One apparent advantage of the cable car is its relative energy efficiency. This is due to the economy of centrally located power stations, and the ability of descending cars to transfer energy to ascending cars. However, this advantage is totally negated by the relatively large energy consumption required to simply move the cable over and under the numerous guide rollers and around the many sheaves. Approximately 95% of the tractive effort in the San Francisco system is expended in simply moving the four cables at 15.3 km/h (9.5 mph).^[11] Electric cars with regenerative braking do offer the advantages, without the problem of moving a cable. In the case of steep grades, however, cable traction has the major advantage of not depending on adhesion between wheels and rails. There is also the advantage that keeping the car gripped to the cable will also limit the downhill speed of the car to that of the cable.

Because of the constant and relatively low speed, a cable car's potential to cause harm in an accident can be underestimated. Even with a cable car traveling at only 14 km/h (9 mph), the mass of the cable car and the combined strength and speed of the cable can cause extensive damage in a collision.

Relation to funiculars

A cable car is superficially similar to a funicular, but differs from such a system in that its cars are not permanently attached to the cable and can stop independently, whereas a funicular has cars that are permanently attached to the propulsion cable, which is itself stopped and started. A cable car cannot climb as steep a grade as a funicular, but many more cars can be operated with a single cable, making it more flexible, and allowing a higher capacity. During the rush hour on San Francisco's Market Street Railway in 1883, a car would leave the terminal every 15 seconds.^[12]

A few funicular railways operate in street traffic, and because of this operation are often incorrectly described as cable cars. Examples of such operation, and the consequent confusion, are:

• The Great Orme Tramway in Llandudno, Wales.
• Several street funiculars in Lisbon, Portugal.

Even more confusingly, a hybrid cable car/funicular line once existed in the form of the original Wellington Cable Car, in the New Zealand city of Wellington. This line had both a continuous loop haulage cable that the cars gripped using a cable car gripper, and a balance cable permanently attached to both cars over an undriven pulley at the top of the line. The descending car gripped the haulage cable and was pulled downhill, in turn pulling the ascending car (which remained ungripped) uphill by the balance cable. This line was rebuilt in 1979 and is now a standard funicular, although it retains its old cable car name.

List of cable car systems

Cities currently operating cable cars

Traditional cable car systems

The best-known existing cable car system is the San Francisco cable car system in the city of San Francisco, California. San Francisco's cable cars constitute the oldest and largest such system in permanent operation, and it is one of the few still functioning in the traditional manner, with manually operated cars running in street traffic. Other examples of cable powered systems can be found on the Great Orme in North Wales. and in Lisbon in Portugal. All of these however are slightly different to San Francisco in that the cars are permanently attached to the cable.

Modern cable car systems

Several cities operate a modern version of the cable car system. These systems are fully automated and run on their own reserved right of way. They are commonly referred to as people movers, although that term is also applied to systems with other forms of propulsion, including funicular style cable propulsion.

These cities include:

• Oakland, California, United States – The Oakland Airport Connector system between the BART rapid transit system and Oakland International Airport, based on Doppelmayr Cable Car's Cable Liner Pinched Loop
• Perugia, Italy – The Perugia People Mover, based on Leitner's MiniMetro
• Shanghai, China - The Bund Sightseeing Tunnel, based on Soulé's SK
• Caracas, Venezuela - The Cabletren Bolivariano, based on Doppelmayr Cable Car's Cable Liner Pinched Loop
• Zürich, Switzerland - The Skymetro connects the Zurich Airport's main Airside Center, Gates A, B and C with its mid-field Gates E, based on OTIS's Otis Hovair

Cities previously operating cable cars

Australia

 

Cable tram and trailer on the St Kilda Line in Melbourne in 1905

• Melbourne (1885–1940, the Melbourne cable tramway system)
• Sydney (1886–1905)

France

• Laon – The Poma 2000 (service ended in 2016)^[13]
• Paris (Tramway funiculaire de Belleville 1873–1935)

Lebanon

• Beirut (Late 1880s until destruction during the Lebanese Civil War)

New Zealand

• Dunedin (1881–1957, the Dunedin cable tramway system)
• Wellington (1902–1979, the original Wellington Cable Car hybrid system)

Philippines

• Manila (Early 1900s-1930s, the Manila-Malabon railway.)

Portugal

• Lisbon (converted to regular tram lines in the early 20th century: São Sebastião, Estrela, and Graça)

United Kingdom

• Birmingham (City of Birmingham Tramways Company Ltd, 1888–1911, converted to electric traction)
• Edinburgh (Edinburgh Corporation Tramways, 1899–1923, converted to electric traction)
• Glasgow (Glasgow Subway, 1896–1935, converted to electric traction)
• Hastings
• Liverpool (trial in 1883)
• London, England (1884–1909, Highgate Hill Cable Tramway connecting Archway with Highgate, the first cable car in regular operation in Europe)
• Matlock (1893–1927, the Matlock Cable Tramway)

Isle of Man

• Douglas (1896–1929, the Upper Douglas Cable Tramway)

United States

 

A Seattle cable car in 1940, just before service ended. Seattle was the last city in the U.S. to abandon all its street cable railways, with the last three lines all closing in 1940, leaving San Francisco as the only U.S. city where cable cars continued to operate.^[14]

• Baltimore, Maryland (1890–1897)
• Binghamton, New York (trial in 1885)
• Brooklyn, New York
  • New York and Brooklyn Bridge Railway
  • Brooklyn Cable Company's Park Avenue Line
  • Brooklyn Heights Railroad's Montague Street Line
• Butte, Montana (1889–1897)
• Chicago, Illinois (1882–1906)
  • Chicago City Railway
  • North Chicago Street Railroad
  • West Chicago Street Railroad
• Cincinnati, Ohio
• Cleveland, Ohio
• Denver, Colorado (1886–1900, the Denver Tramway)
• Grand Rapids, Michigan
• Hoboken, New Jersey (1886–1892, the North Hudson County Railway's Hoboken Elevated)
• Kansas City, Missouri (1885–1913), including 9th St Incline (1888–1902), 8th St. Tunnel in use (1887–1956)
• Los Angeles, California (1885–1889) Second Street Cable Railway, (1886–1902) Temple Street Cable Railway, (1889–1896) Los Angeles Cable Railway
• New York City
  • West Side and Yonkers Patent Railway's Ninth Avenue Line
  • New York and Brooklyn Bridge Railway
  • Third Avenue Railroad's 125th Street Crosstown Line
  • Third Avenue Railroad's Third Avenue Line
  • Metropolitan Street Railway's Broadway Line
  • Metropolitan Street Railway's Broadway and Columbus Avenue Line
  • Metropolitan Street Railway's Broadway and Lexington Avenue Line
  • IRT Ninth Avenue Line (defunct)
• Newark, New Jersey (1888–1889)
• Oakland, California (1886–1899)
• Omaha, Nebraska
• Philadelphia, Pennsylvania
• Pittsburgh, Pennsylvania
• Portland, Oregon (1890–1904)
• Providence, Rhode Island
• St. Louis, Missouri
• Saint Paul, Minnesota
• San Diego, California (1890–1892)
• Seattle, Washington (1888–1940)^[15]
• Sioux City, Iowa
• Spokane, Washington (1899–1936)
• Tacoma, Washington (1891–1938)^[16]
• Tulsa, Oklahoma
• Washington, D.C. (1890–1899, part of the Washington streetcar system)
• Wichita, Kansas

See also

• Aerial tramway
• Cable car – Disambiguation
• Cable railway
• Cable ferry
• Cable Liner
• Elevator
• Funicular
• Glasgow Subway
• Grade (slope)
• IRT Ninth Avenue Line
• List of funicular railways
• Rack railway (Cog railway)
• Reaction ferry
• San Francisco cable car system

References

Specific

1. Hilton, George W. (1971). The Cable Car in America. Berkeley, CA.: Howell NorthBooks.
2. "The Cable in Chicago: Speeding along the Streets Rapid Transit there for Miles". The Baltimore Sun, page 8. Nov 9, 1889.
3. Erskine Hazard, Observations upon Rail-roads, The Franklin Journal and American Mechanics' Magazine, Vol. III, No. 4 (April 1827); page 275.
4. Fawdon Wagonway, Structural Images of the North East 2012-09-02 at the Wayback Machine, University of Newcastle upon Tyne, 26 Mar. 2004.
5. Robertson, Andrew (March 1848). "Blackwall Railway Machinery". The Civil Engineer and Architect's Journal. New York: Wiley & Putnam. 11.
6. James Guilbeau (2011). St. Charles Streetcar, The: Or, the New Orleans & Carrollton Railroad. Pelican Publishing Company. pp. 48–49. ISBN 9781879714021.
7. Louis C. Hennick; Elbridge Harper Charlton (1965). The Streetcars of New Orleans. Pelican Publishing. p. 16. ISBN 9781455612598.
8. . Archived from the original on 2016-12-20. Retrieved 2016-03-29.
9. Taylor, Sheila (2001). The Moving Metropolis. London: Calmann and King. p. 82. ISBN 1-85669-241-8.
10. Reardon, Patrick T. (2021). The Loop: The "L" Tracks That Shaped and Saved Chicago. Carbondale, Illinois: Southern Illinois University Press. p. 60. ISBN 9780809338108. from the original on 2024-02-07. Retrieved 2023-03-18.
11. Source: San Francisco Municipal Railway
12. Evanosky, Dennis (2013). Lost San Francisco. Pavilion Books. p. 60. ISBN 9781909815247.
13. "POMA" (in French). Transports Urbain Laonnois. from the original on 2009-04-21. Retrieved 2009-04-02.
14. Hilton (1982), p. 167.
15. Hilton (1982), pp. 389–407.
16. Hilton (1982), p. 465.

General

• Hilton, George W. (1982). The Cable Car in America (Revised Edition). San Diego, California: Howell–North Books. Reprinted 1997 by Stanford University Press. ISBN 0-8047-3051-2.
• Of Cables and Grips: The Cable Cars of San Francisco, by Robert Callwell and Walter Rice, published by Friends of the Cable Car Museum, first edition, 2000.
• Chicago Cable Cars, by Greg Borzo, published by The History Press (2012), ISBN 978-1-60949-327-1

External links

 

Wikimedia Commons has media related to Cable car on rails.

 

Wikimedia Commons has media related to Cable cars (railway).

 

Wikisource has the text of The New Student's Reference Work article "Cable-Road".

Information

• Cable Car Museum
• Cable Car Guy
• a scripophily based article re. the San Francisco Cal Cable and the Swiss Borel Bankers (in German)
• (New York City) Broadway Cable car line.
• How Cable Cars Operate San Francisco Cable Car Museum
• San Francisco Cable Car Movie from 1905

Patents

• U.S. patent 19,736 – Railroad track
• U.S. patent 110,971 – Endless wire ropeway