USB hardware

This article is about the physical and electrical aspects of USB connections. For the standard in general, see USB.

The initial versions of the USB standard specified connectors that were easy to use and that would have acceptable life spans; revisions of the standard added smaller connectors useful for compact portable devices. Higher-speed development of the USB standard gave rise to another family of connectors to permit additional data paths. All versions of USB specify cable properties; version 3.x cables include additional data paths. The USB standard included power supply to peripheral devices; modern versions of the standard extend the power delivery limits for battery charging and devices requiring up to 240 watts. USB has been selected as the standard charging format for many mobile phones, reducing the proliferation of proprietary chargers.

Various legacy USB connectors along a centimeter ruler for scale. From left to right:

1. Micro-B plug
2. Proprietary UC-E6 connector used on many older Japanese cameras for both USB and analog AV output
3. Mini-B plug
4. Standard-A receptacle, non-compliant because USB does not allow extensions cables
5. Standard-A plug
6. Standard-B plug

Connectors

 

Comparison of legacy USB connector plugs, omitting the current standard Type-C plugs

Unlike other data buses (such as Ethernet), USB connections are directed; a host device has "downstream" facing ports that connect to the "upstream" facing ports of devices. Only downstream facing ports provide power; this topology was chosen to easily prevent electrical overloads and damaged equipment. Thus, USB cables have different ends: A and B, with different physical connectors for each. Each format has a plug and receptacle defined for each of the A and B ends. A USB cable, by definition, has a plug on each end—one A (or C) and one B (or C)—and the corresponding receptacle is usually on a computer or electronic device. The mini and micro formats may connect to an AB receptacle, which accepts either an A or a B plug, that plug determining the behavior of the receptacle.

The three sizes of USB connectors are the default, or standard, format intended for desktop or portable equipment, the mini intended for mobile equipment, which was deprecated when it was replaced by the thinner micro size, all of which were deprecated in USB 3.2 in favor of Type-C. There are five speeds for USB data transfer: Low Speed, Full Speed, High Speed (from version 2.0 of the specification), SuperSpeed (from version 3.0), and SuperSpeed+ (from version 3.1). The modes have differing hardware and cabling requirements. USB devices have some choice of implemented modes, and USB version is not a reliable statement of implemented modes. Modes are identified by their names and icons, and the specification suggests that plugs and receptacles be color-coded (SuperSpeed is identified by blue).

Connector properties

 

Non-standard "USB extension cable", plug on the left, receptacle on the right. (USB does not allow extension cables. Non-standard cables may work but cannot be presumed reliable.)

The connectors the USB committee specifies support a number of USB's underlying goals, and reflect lessons learned from the many connectors the computer industry has used. The connector mounted on the host or device is called the receptacle, and the connector attached to the cable is called the plug.^[1] The official USB specification documents also periodically define the term male to represent the plug, and female to represent the receptacle, though these uses are inconsistent with established definitions of connector gender.^{[2][clarification needed]}

By design, it is difficult to insert a USB plug into its receptacle incorrectly. The USB specification requires that the cable plug and receptacle be marked so the user can recognize the proper orientation.^[1] The USB-C plug however is reversible. USB cables and small USB devices are held in place by the gripping force from the receptacle, with no screws, clips, or thumb-turns as other connectors use.

The different A and B plugs prevent accidentally connecting two power sources. However, some of this directed topology is lost with the advent of multi-purpose USB connections (such as USB On-The-Go in smartphones, and USB-powered Wi-Fi routers), which require A-to-A, B-to-B, and sometimes Y/splitter cables. See the USB On-The-Go connectors section below for a more detailed summary description.

There are so-called cables with A plugs on both ends, which may be valid if the "cable" includes, for example, a USB host-to-host transfer device with two ports.^[3] This is, by definition, a device with two logical B ports, each with a captive cable, not a cable with two A ends.

Durability

The standard connectors were designed to be more robust than many past connectors. This is because USB is hot-swappable, and the connectors would be used more frequently, and perhaps with less care, than previous connectors.

Standard USB has a minimum rated lifetime of 1,500 cycles of insertion and removal,^[4] the Mini-USB receptacle increased this to 5,000 cycles,^[4] and the newer Micro-USB^[4] and USB-C receptacles are both designed for a minimum rated lifetime of 10,000 cycles of insertion and removal.^[5] To accomplish this, a locking device was added and the leaf-spring was moved from the jack to the plug, so that the most-stressed part is on the cable side of the connection. This change was made so that the connector on the less expensive cable would bear the most wear.^{[4][page needed]}

In standard USB, the electrical contacts in a USB connector are protected by an adjacent plastic tongue, and the entire connecting assembly is usually protected by an enclosing metal shell.^[4]

The shell on the plug makes contact with the receptacle before any of the internal pins. The shell is typically grounded, to dissipate static electricity and to shield the wires within the connector.

Compatibility

The USB standard specifies tolerances for compliant USB connectors to minimize physical incompatibilities in connectors from different vendors. The USB specification also defines limits to the size of a connecting device in the area around its plug, so that adjacent ports are not blocked. Compliant devices must either fit within the size restrictions or support a compliant extension cable that does.

Pinouts

See also: USB 3.0 § Pinouts

USB 2.0 uses two wires for power (V_BUS and GND), and two for differential serial data signals. Mini and micro connectors have their GND connections moved from pin #4 to pin #5, while their pin #4 serves as an ID pin for the On-The-Go host/client identification.^[6]

USB 3.0 provides two additional differential pairs (four wires, SSTx+, SSTx−, SSRx+ and SSRx−), providing full-duplex data transfers at SuperSpeed, which makes it similar to Serial ATA or single-lane PCI Express.

 

Standard, Mini-, and Micro-USB plugs shown end-on, not to scale. Light areas represent cavities. The plugs are pictured with USB logo to the top.^[7]

 

Micro-B SuperSpeed plug

1. Power (V_BUS, 5 V)
2. Data− (D−)
3. Data+ (D+)
4. ID (On-The-Go)
5. GND
6. SuperSpeed transmit− (SSTx−)
7. SuperSpeed transmit+ (SSTx+)
8. GND
9. SuperSpeed receive− (SSRx−)
10. SuperSpeed receive+ (SSRx+)

Type-A and -B pinout

Pin	Name	Wire color^[a]		Description
1	VBUS	Red or	Orange	+5 V
2	D−	White or	Gold	Data−
3	D+	Green		Data+
4	GND	Black or	Blue	Ground

Mini/Micro-A and -B pinout

Pin	Name	Wire color^[a]	Description
1	VBUS	Red	+5 V
2	D−	White	Data−
3	D+	Green	Data+
4	ID	No wire	On-The-Go ID distinguishes cable ends: "A" plug (host): connected to GND "B" plug (device): not connected
5	GND	Black	Signal ground

1. In some sources D+ and D− are erroneously swapped.

Colors

 

A yellow charge-only "USB" Type-A receptacle and a USB 3.0 Type-A receptacle, both upside-down, on a front panel with card reader

 

A blue Standard-A USB receptacle without USB 3.0 contacts fitted

Usual USB color-coding

Color							Location	Description
						Black or white	Receptacles and plugs	Type-A or Type-B
						Blue (Pantone 300C)	Receptacles and plugs	Type-A or Type-B, SuperSpeed
						Teal blue	Receptacles and plugs	Type-A or Type-B, SuperSpeed+
						Green	Receptacles and plugs	Type-A or Type-B, Qualcomm Quick Charge (QC)
						Purple	Plugs only	Type-A or Type-C, Huawei SuperCharge
						Yellow or red	Receptacles only	High-current or sleep-and-charge
						Orange	Receptacles only	High-retention connector, mostly used on industrial hardware

USB ports and connectors are often color-coded to distinguish their different functions and USB versions. These colors are not part of the USB specification and can vary between manufacturers; for example, the USB 3.0 specification mandates appropriate color-coding while it only recommends blue inserts for Standard-A USB 3.0 connectors and plugs.^[8]

Connector types

USB connector types multiplied as the specification progressed. The original USB specification detailed standard-A and standard-B plugs and receptacles. The connectors were different so that users could not connect one computer receptacle to another. The data pins in the standard plugs are recessed compared to the power pins so that the device can power up before establishing a data connection. Some devices operate in different modes depending on whether the data connection is made. Charging docks supply power and do not include a host device or data pins, allowing any capable USB device to charge or operate from a standard USB cable. Charging cables provide power connections, but not data. In a charge-only cable, the data wires are shorted at the device end, otherwise, the device may reject the charger as unsuitable.

Standard connectors

 

Pin configuration of Type-A and Type-B plugs viewed end-on

• The Type-A plug. This plug has an elongated rectangular cross-section, inserts into a Type-A receptacle on a downstream port on a USB host or hub, and carries both power and data. Captive cables on USB devices such as keyboards or mice terminate with a Type-A plug.
• The Type-B plug: This plug has a near square cross-section with the top exterior corners beveled. As part of a removable cable, it inserts into an upstream port on a device, such as a printer. On some devices, the Type-B receptacle has no data connections, being used solely for accepting power from the upstream device. This two-connector-type scheme (A/B) prevents a user from accidentally creating a loop.^[9][10]

The maximum allowed cross-section of the overmold boot (which is part of the connector used for its handling) is 16 by 8 mm (0.63 by 0.31 in) for the Standard-A plug type, while for the Type-B it is 11.5 by 10.5 mm (0.45 by 0.41 in).^[2]

Mini connectors

 

Mini-A (left) and Mini-B (right) plugs

Mini-USB connectors were introduced together with USB 2.0 in April 2000, mostly used with smaller devices such as digital cameras, smartphones, and tablet computers. The Mini-A connector and the Mini-AB receptacle connector have been deprecated since May 2007.^[11] Mini-B connectors are still supported, but are not On-The-Go-compliant;^[12] the Mini-B USB connector was standard for transferring data to and from the early smartphones and PDAs. Both Mini-A and Mini-B plugs are approximately 3 by 7 mm (0.12 by 0.28 in). The Mini-AB receptacle accepts either a Mini-A or Mini-B plug.

Micro connectors

 

Micro-A
plug

 

Micro-B
plug

Micro-USB connectors, which were announced by the USB-IF on January 4, 2007,^[13][14] have a similar width to Mini-USB, but approximately half the thickness, enabling their integration into thinner portable devices. The Micro-A connector is 6.85 by 1.8 mm (0.270 by 0.071 in) with a maximum overmold boot size of 11.7 by 8.5 mm (0.46 by 0.33 in), while the Micro-B connector is 6.85 by 1.8 mm (0.270 by 0.071 in) with a maximum overmold size of 10.6 by 8.5 mm (0.42 by 0.33 in).^[7]

The thinner Micro-USB connectors were intended to replace the Mini connectors in devices manufactured since May 2007, including smartphones, personal digital assistants, and cameras.^[15]

The Micro plug design is rated for at least 10,000 connect-disconnect cycles, which is more than the Mini plug design.^[13][16] The Micro connector is also designed to reduce the mechanical wear on the device; instead, the easier-to-replace cable is designed to bear the mechanical wear of connection and disconnection. The Universal Serial Bus Micro-USB Cables and Connectors Specification details the mechanical characteristics of Micro-A plugs, Micro-AB receptacles (which accept both Micro-A and Micro-B plugs), Double-Sided Micro USB, and Micro-B plugs and receptacles,^[16] along with a Standard-A receptacle to a Micro-A plug adapter.

OMTP standard

Micro-USB was endorsed as the standard connector for data and power on mobile devices by the cellular phone carrier group Open Mobile Terminal Platform (OMTP) in 2007.^[17]

Micro-USB was embraced as the "Universal Charging Solution" by the International Telecommunication Union (ITU) in October 2009.^[18]

In Europe, micro-USB became the defined common external power supply (EPS) for use with smartphones sold in the EU,^[19] and 14 of the world's largest mobile phone manufacturers signed the EU's common EPS Memorandum of Understanding (MoU).^[20][21] Apple, one of the original MoU signers, makes Micro-USB adapters available—as permitted in the Common EPS MoU—for its iPhones equipped with Apple's proprietary 30-pin dock connector or (later) Lightning connector.^[22][23] according to the CEN, CENELEC, and ETSI.

USB 3.x connectors and backward compatibility

 

USB 3.0 Micro-B SuperSpeed plug

See also: USB 3.0 § Connectors

USB 3.0 introduced Type-A SuperSpeed plugs and receptacles as well as micro-sized Type-B SuperSpeed plugs and receptacles. The 3.0 receptacles are backward-compatible with the corresponding pre-3.0 plugs.

USB 3.x and USB 1.x Type-A plugs and receptacles are designed to interoperate. To achieve USB 3.0's SuperSpeed (and SuperSpeed+ for USB 3.1 Gen 2), 5 extra pins are added to the unused area of the original 4 pin USB 1.0 design, making USB 3.0 Type-A plugs and receptacles backward compatible to those of USB 1.0.

On the device side, a modified Micro-B plug (Micro-B SuperSpeed) is used to cater for the five additional pins required to achieve the USB 3.0 features (USB-C plug can also be used). The USB 3.0 Micro-B plug effectively consists of a standard USB 2.0 Micro-B cable plug, with an additional 5 pins plug "stacked" to the side of it. In this way, cables with smaller 5 pin USB 2.0 Micro-B plugs can be plugged into devices with 10 contact USB 3.0 Micro-B receptacles and achieve backward compatibility.

USB cables exist with various combinations of plugs on each end of the cable, as displayed below in the USB cables matrix.

 

USB 3.0 Standard-B plug

USB On-The-Go connectors

Main article: USB On-The-Go

USB On-The-Go (OTG) introduces the concept of a device performing both host and device roles. All current OTG devices are required to have one, and only one, USB connector: a Micro-AB receptacle. (In the past, before the development of Micro-USB, On-The-Go devices used Mini-AB receptacles.)

The Micro-AB receptacle is capable of accepting Micro-A and Micro-B plugs, attached to any of the legal cables and adapters as defined in revision 1.01 of the Micro-USB specification.

To enable Type-AB receptacles to distinguish which end of a cable is plugged in, plugs have an "ID" pin in addition to the four contacts in standard-size USB connectors. This ID pin is connected to GND in Type-A plugs, and left unconnected in Type-B plugs. Typically, a pull-up resistor in the device is used to detect the presence or absence of an ID connection.

The OTG device with the A-plug inserted is called the A-device and is responsible for powering the USB interface when required, and by default assumes the role of host. The OTG device with the B-plug inserted is called the B-device and by default assumes the role of peripheral. An OTG device with no plug inserted defaults to acting as a B-device. If an application on the B-device requires the role of host, then the Host Negotiation Protocol (HNP) is used to temporarily transfer the host role to the B-device.

OTG devices attached either to a peripheral-only B-device or a standard/embedded host have their role fixed by the cable, since in these scenarios it is only possible to attach the cable one way.^{[citation needed]}

USB-C

Main article: USB-C

 

The USB-C plug

 

USB cable with a USB-C plug and a USB-C port on a notebook computer

The USB-C connector supersedes all earlier USB connectors and the Mini DisplayPort connector. It is used for all USB protocols and for Thunderbolt (3 and later), DisplayPort (1.2 and later), and others. Developed at roughly the same time as the USB 3.1 specification, but distinct from it, the USB-C Specification 1.0 was finalized in August 2014^[24] and defines a new small reversible-plug connector for USB devices.^[25] The USB-C plug connects to both hosts and devices, replacing various Type-A and Type-B connectors and cables with a standard meant to be future-proof.^[24][26]

The 24-pin double-sided connector provides four power–ground pairs, two differential pairs for USB 2.0 data (though only one pair is implemented in a USB-C cable), four pairs for SuperSpeed data bus (only two pairs are used in USB 3.1 mode), two "sideband use" pins, V_CONN +5 V power for active cables, and a configuration pin for cable orientation detection and dedicated biphase mark code (BMC) configuration data channel (CC).^[27][28] Type-A and Type-B adaptors and cables are required for older hosts and devices to plug into USB-C hosts and devices. Adapters and cables with a USB-C receptacle are not allowed.^[29]

Full-featured USB-C 3.1 cables contain a full set of wires and are "electronically marked" (E-marked): they contain a "eMarker" chip that responds to the USB Power Delivery Discover Identity command, a kind of vendor-defined message (VDM) sent over the configuration data channel (CC). Using this command, the cable reports its current capacities, maximum speed, and other parameters.^{[30]: §4.9} Full-Featured USB Type-C devices are a mechanic prerequisite for multi-lane operation (USB 3.2 Gen 1x2, USB 3.2 Gen 2x2, USB4 2x2, USB4 3x2, USB Gen 4 Asymmetric).^[30]

USB-C devices support power currents of 1.5 A and 3.0 A over the 5 V power bus in addition to baseline 900 mA. These higher currents can be negotiated through the configuration line. Devices can also utilize the full Power Delivery specification using both BMC-coded configuration line and legacy BFSK-coded V_BUS line.^{[30]: §4.6.2.1}

Host and device interface receptacles

USB plugs fit one receptacle with notable exceptions for USB On-The-Go "AB" support and the general backward compatibility of USB 3.0 as shown.

USB connector mating table (images not to scale)

Plug Receptacle	USB A	USB 3.0 A SS	USB B	USB 3.0 B SS	USB Mini-A	USB Mini-B	USB Micro-A^1	USB Micro-B	USB 3.0 Micro-B	USB-C
USB A	Yes	Only non- SuperSpeed	No	No	No	No	No	No	No	No
USB 3.0 A SS	Only non- SuperSpeed	Yes	No	No	No	No	No	No	No	No
USB B	No	No	Yes	No	No	No	No	No	No	No
USB 3.0 B SS	No	No	Only non- SuperSpeed	Yes	No	No	No	No	No	No
USB Mini-A	No	No	No	No	Yes	No	No	No	No	No
USB Mini-AB	No	No	No	No	Deprecated	Deprecated	No	No	No	No
USB Mini-B	No	No	No	No	No	Yes	No	No	No	No
USB Micro-AB	No	No	No	No	No	No	Yes	Yes	No	No
USB Micro-B	No	No	No	No	No	No	No	Yes	No	No
USB 3.0 Micro-B SS	No	No	No	No	No	No	No	Only non- SuperSpeed	Yes	No
USB-C	No	No	No	No	No	No	No	No	No	Yes
^1 No corresponding Micro-A receptacle was ever designed.

USB cables table

Plugs, each end	USB A	USB Mini-A	USB Micro-A	USB B	USB Mini-B	USB Micro-B	USB 3.0 Micro-B	USB-C
USB A	Proprietary, hazardous	Proprietary, hazardous	Proprietary, hazardous	Yes	Yes	Yes	Yes	Yes
USB Mini-A	Proprietary, hazardous	No	No	Deprecated	Deprecated	Non- standard	No	No
USB Micro-A	Proprietary, hazardous	No	No	Non- standard	Non- standard	Yes	No	No
USB B	Yes	Deprecated	Non- standard	No	No	No	No	Yes
USB Mini-B	Yes	Deprecated	Non- standard	No	OTG non- standard	OTG non- standard	No	Yes
USB Micro-B	Yes	Non- standard	Yes	No	OTG non- standard	OTG non- standard	No	Yes
USB 3.0 Micro-B	Yes	No	No	No	No	No	OTG non- standard	Yes
USB-C	Yes	No	No	Yes	Yes	Yes	Yes	Yes

  Proprietary, hazardous

Existing for specific proprietary purposes, not inter-operable with USB-IF compliant equipment and possibly damaging to both devices when plugged in. In addition to the above cable assemblies comprising two plugs, an "adapter" cable with a Micro-A plug and a standard-A receptacle is compliant with USB specifications.^[7] Other combinations of connectors are not compliant.

There do exist A-to-A assemblies, referred to as cables (such as the Easy Transfer Cable); however, these have a pair of USB devices in the middle, making them more than just cables.

  Non-standard

The USB standards do not exhaustively list all combinations with one Type-A and one Type-B connector, however, most such cables have good chances of working.

  OTG non-standard

Commonly available "OTG" cables that address widespread misuse of Micro-B and Mini-B receptacles for OTG devices, e.g. smartphones (as opposed to Micro-AB and Mini-AB, which accept either plug.) While not compliant with the USB standards, these cables at least do not provide a device damage hazard since Type-B ports on devices are unpowered by default.^[31]

  Deprecated

Some older devices and cables with Mini-A connectors have been certified by USB-IF. The Mini-A connector is obsolete: no new Mini-A connectors and neither Mini-A nor Mini-AB receptacles will be certified.^[11]

Note: Mini-B is not deprecated, although it is less and less used since the arrival of Micro-B. Micro-A and Micro-B have one more contact than Standard-A and Standard-B in order for hardware with a Micro-AB receptacle to discern Micro-A from Micro-B and behave as a host or device accordingly.

Proprietary connectors and formats

Manufacturers of personal electronic devices might not include a USB standard connector on their product for technical or marketing reasons.^[32] E.g. Olympus has been using a special cable called CB-USB8 one end of which has a special contact. Some manufacturers provide proprietary cables, such as Lightning, that permit their devices to physically connect to a USB standard port. Full functionality of proprietary ports and cables with USB standard ports is not assured; for example, some devices only use the USB connection for battery charging and do not implement any data transfer functions.^[33]

Cabling

 

A USB twisted pair, in which the Data+ and Data− conductors are twisted together in a double helix. The wires are enclosed in a further layer of shielding.

The D± signals used by low, full, and high speed are carried over a twisted pair (typically unshielded) to reduce noise and crosstalk. SuperSpeed uses separate transmit and receive differential pairs, which additionally require shielding (typically, shielded twisted pair but twinax is also mentioned by the specification). Thus, to support SuperSpeed data transmission, cables contain twice as many wires and are larger in diameter.^[34]

The USB 1.1 standard specifies that a standard cable can have a maximum length of 5 meters (16 ft 5 in) with devices operating at full speed (12 Mbit/s), and a maximum length of 3 meters (9 ft 10 in) with devices operating at low speed (1.5 Mbit/s).^[35][36][37]

USB 2.0 provides for a maximum cable length of 5 meters (16 ft 5 in) for devices running at high speed (480 Mbit/s). The primary reason for this limit is the maximum allowed round-trip delay of about 1.5 μs. If USB host commands are unanswered by the USB device within the allowed time, the host considers the command lost. When adding USB device response time, delays from the maximum number of hubs added to the delays from connecting cables, the maximum acceptable delay per cable amounts to 26 ns.^[37] The USB 2.0 specification requires that cable delay be less than 5.2 ns/m (1.6 ns/ft, 192000 km/s), which is close to the maximum achievable transmission speed for standard copper wire.

The USB 3.0 standard does not directly specify a maximum cable length, requiring only that all cables meet an electrical specification: for copper cabling with AWG 26 wires the maximum practical length is 3 meters (9 ft 10 in).^[38]

Power

See also: USB hub § Power

Upstream USB connectors supply power at a nominal 5 V DC via the V_BUS pin to downstream USB devices.

Voltage tolerance and limits

 

Worst-case voltage drop topology of a USB 2.0 host to low-power device chain, at steady state

The tolerance on V_BUS at an upstream (or host) connector was originally ±5% (i.e. could lie anywhere in the range 4.75 V to 5.25 V). With the release of the USB Type-C specification in 2014 and its 3 A power capability, the USB-IF elected to increase the upper voltage limit to 5.5 V to combat voltage droop at higher currents.^[39] The USB 2.0 specification (and therefore implicitly also the USB 3.x specifications) was also updated to reflect this change at that time.^[40] A number of extensions to the USB Specifications have progressively further increased the maximum allowable V_BUS voltage: starting with 6.0V with USB BC 1.2,^[41] to 21.5 V with USB PD 2.0^[42] and 50.9 V with USB PD 3.1,^[42] while still maintaining backwards compatibility with USB 2.0 by requiring various forms of handshake before increasing the nominal voltage above 5 V.

USB PD continues the use of the bilateral 5% tolerance, with allowable voltages of PDO ±5% ±0.5 V (eg. for a PDO of 9.0 V, the maximum and minimum limits are 9.95 V and 8.05 V, respectively).^[42]

There are several minimum allowable voltages defined at different locations within a chain of connectors, hubs, and cables between an upstream host (providing the power) and a downstream device (consuming the power). To allow for voltage drops, the voltage at the host port, hub port, and device are specified to be at least 4.75 V, 4.4 V, and 4.35 V respectively by USB 2.0 for low-power devices,^[a] but must be at least 4.75 V at all locations for high-power^[b] devices (however, high-power devices are required to operate as a low-powered device so that they may be detected and enumerated if connected to a low-power upstream port). The USB 3.x specifications require that all devices must operate down to 4.00 V at the device port.

Unlike USB 2.0 and USB 3.2, USB4 does not define its own VBUS-based power model. Power for USB4 operation is established and managed as defined in the USB Type-C Specification and the USB PD Specification.

1. Low-power devices are those which draw less than 1 unit load. 1 unit load is 100 mA for USB 2.0
2. High-power devices in USB 2.0 are those draw more than one unit load (up to a maximum of 5 unit loads). 1 unit load is 100mA.

 

Worst-case voltage drop topology of a USB 3.x host to device chain, at steady state. Note that under transient conditions the supply at the device can momentarily drop from 4.0 V to 3.67 V.

Allowable current draw

USB power standards

Specification	Current	Voltage	Power (max.)
Low-power device	100 mA	5 V	0.50 W
Low-power SuperSpeed (USB 3.0) device	150 mA	5 V	0.75 W
High-power device	500 mA^[a]	5 V	2.5 W
High-power SuperSpeed (USB 3.0) device	900 mA^[b]	5 V	4.5 W
Battery Charging (BC) 1.2	1.5 A	5 V	7.5 W
Single-lane SuperSpeed+ (USB 3.2 Gen2x1, and former USB 3.1 Gen2) device	1.5 A^[c]	5 V	7.5 W
USB-C (single-lane)	1.5 A^[c]	5 V	7.5 W
USB-C (multi-lane)	3 A	5 V	15 W
Power Delivery 1.0/2.0/3.0 Type-C	5 A^[d]	20 V	100 W
Power Delivery 3.1 Type-C	5 A^[d]	48 V^[e]	240 W
Up to 5 unit loads; with non-SuperSpeed devices, one unit load is 100 mA. Up to 6 unit loads; with SuperSpeed devices, one unit load is 150 mA. Up to 6 unit loads; with multi-lane devices, one unit load is 250 mA. >3 A (>60 W) operation requires an electronically marked cable rated at 5 A. >20 V (>60 W) operation requires an electronically marked Extended Power Range (EPR) cable.

The limit to device power draw is stated in terms of a unit load which is 100 mA for USB 2.0, or 150 mA for SuperSpeed (i.e. USB 3.x) devices. Low-power devices may draw at most 1 unit load, and all devices must act as low-power devices before they are configured. A high-powered device must be configured, after which it may draw up to 5 unit loads (500 mA), or 6 unit loads (900 mA) for SuperSpeed devices, as specified in its configuration because the maximum power may not always be available from the upstream port.^{[43][44][45][46]}

A bus-powered hub is a high-power device providing low-power ports. It draws 1 unit load for the hub controller and 1 unit load for each of at most 4 ports. The hub may also have some non-removable functions in place of ports. A self-powered hub is a device that provides high-power ports by supplementing the power supply from the host with its own external supply. Optionally, the hub controller may draw power for its operation as a low-power device, but all high-power ports must draw from the hub's self-power.

Where devices (for example, high-speed disk drives) require more power than a high-power device can draw,^[47] they function erratically, if at all, from bus power of a single port. USB provides for these devices as being self-powered. However, such devices may come with a Y-shaped cable that has two USB plugs (one for power and data, the other for only power), so as to draw power as two devices.^[48] Such a cable is non-standard, with the USB compliance specification stating that "use of a 'Y' cable (a cable with two A-plugs) is prohibited on any USB peripheral", meaning that "if a USB peripheral requires more power than allowed by the USB specification to which it is designed, then it must be self-powered."^[49]

USB battery charging

USB Battery Charging (BC) defines a charging port, which may be a charging downstream port (CDP), with data, or a dedicated charging port (DCP) without data. Dedicated charging ports can be found on USB power adapters to run attached devices and battery packs. Charging ports on a host with both kinds will be labeled.^[50]

The charging device identifies a charging port by non-data signaling on the D+ and D− terminals. A dedicated charging port places a resistance not exceeding 200 Ω across the D+ and D− terminals.^{[50]: § 1.4.7; table 5-3}

Per the base specification, any device attached to a standard downstream port (SDP) must initially be a low-power device, with high-power mode contingent on later USB configuration by the host. Charging ports, however, can immediately supply between 0.5 and 1.5 A of current. The charging port must not apply current limiting below 0.5 A, and must not shut down below 1.5 A or before the voltage drops to 2 V.^[50]

Since these currents are larger than in the original standard, the extra voltage drop in the cable reduces noise margins, causing problems with High Speed signaling. Battery Charging Specification 1.1 specifies that charging devices must dynamically limit bus power current draw during High Speed signaling;^[51] 1.2 specifies that charging devices and ports must be designed to tolerate the higher ground voltage difference in High Speed signaling.

Revision 1.2 of the specification was released in 2010. It made several changes, and increased limits including allowing 1.5 A on charging downstream ports for unconfigured devices—allowing High Speed communication while having a current up to 1.5 A. Also, support was removed for charging port detection via resistive mechanisms.^[52]

Before the Battery Charging Specification was defined, there was no standardized way for the portable device to inquire how much current was available. For example, Apple's iPod and iPhone chargers indicate the available current by voltages on the D− and D+ lines. When D+ = D− = 2.0 V, the device may pull up to 900 mA. When D+ = 2.0 V and D− = 2.8 V, the device may pull up to 1 A of current.^[53] When D+ = 2.8 V and D− = 2.0 V, the device may pull up to 2 A of current.^[54]

Accessory charging adapters (ACA)

Portable devices having a USB On-The-Go port may want to charge and access a USB peripheral simultaneously, yet having only a single port (both due to On-The-Go and space requirement) prevents this. Accessory charging adapters (ACA) are devices that provide portable charging power to an On-The-Go connection between host and peripheral.

ACAs have three ports: the OTG port for the portable device, which is required to have a Micro-A plug on a captive cable; the accessory port, which is required to have a Micro-AB or type-A receptacle; and the charging port, which is required to have a Micro-B receptacle, or type-A plug or charger on a captive cable. The ID pin of the OTG port is not connected within plug as usual, but to the ACA itself, where signals outside the OTG floating and ground states are used for ACA detection and state signaling. The charging port does not pass data, but does use the D± signals for charging port detection. The accessory port acts as any other port. When appropriately signaled by the ACA, the portable device can charge from the bus power as if there were a charging port present; any OTG signals over bus power are instead passed to the portable device via the ID signal. Bus power is also provided to the accessory port from the charging port transparently.^[50]

USB Power Delivery

 

The USB Type-C Charging logo (USB4 20 Gbps port)

USB PD Rev. 1.0 source profiles^[55]

Profile	+5 V	+12 V	+20 V
0	Reserved
1	2.0 A, 10 W^[a]	—	—
2		1.5 A, 18 W
3		3.0 A, 36 W
4			3.0 A, 60 W
5		5.0 A, 60 W	5.0 A, 100 W
Default start-up profile

USB Power Delivery rev. 2.0/3.x power rules

Power (W)	Minimum USB‑C cable required	Current (A), at:
		+5 V	+9 V	+15 V	+20 V	+28 V	+36 V	+48 V
0.5–15	Any^[A]^[56]^[57]^[58]	0.1–3.0	—	—	—	—	—	—
15–27		—	1.67–3.0
27–45			—	1.8–3.0
45–60				—	2.25–3.0
60–100	5 A, or 100 W^[B]	—	—	—	3.0–5.0	—	—	—
100–140^[C]	240 W^[D]^[B]^[58]	—	—	—	—	3.57–5.0	—	—
140–180^[C]						—	3.89–5.0
180–240^[C]							—	3.75–5.0
60 W label required on both plug bodies by current standard, not required on older cables Electronically marked USB PD Extended Power Range 240 W label required on both plug bodies

 

Power rule of USB Power Delivery Revision 3.0, Version 1.2

In July 2012, the USB Promoters Group announced the finalization of the USB Power Delivery (USB-PD) specification (USB PD rev. 1), an extension that specifies using certified PD aware USB cables with standard USB Type-A and Type-B connectors to deliver increased power (more than 7.5 W maximum allowed by the previous USB Battery Charging specification) to devices with greater power demands. (USB-PD A and B plugs have a mechanical mark while Micro plugs have a resistor or capacitor attached to the ID pin indicating the cable capability.) USB-PD Devices can request higher currents and supply voltages from compliant hosts—up to 2 A at 5 V (for a power consumption of up to 10 W), and optionally up to 3 A or 5 A at either 12 V (36 W or 60 W) or 20 V (60 W or 100 W).^[59] In all cases, both host-to-device and device-to-host configurations are supported.^[60]

The intent is to permit uniformly charging laptops, tablets, USB-powered disks and similarly higher-power consumer electronics, as a natural extension of existing European and Chinese mobile telephone charging standards. This may also affect the way electric power used for small devices is transmitted and used in both residential and public buildings.^[61][62] The standard is designed to coexist with the previous USB Battery Charging specification.^[63]

The first Power Delivery specification (Rev. 1.0) defined six fixed power profiles for the power sources. PD-aware devices implement a flexible power management scheme by interfacing with the power source through a bidirectional data channel and requesting a certain level of electrical power, variable up to 5 A and 20 V depending on supported profile. The power configuration protocol can use BMC coding over the CC (configuration channel) wire if one is present, or a 24 MHz BFSK-coded transmission channel on the V_BUS line.^[62]

The USB Power Delivery specification revision 2.0 (USB PD Rev. 2.0) has been released as part of the USB 3.1 suite.^[56][64][65] It covers the USB-C cable and connector with a separate configuration channel, which now hosts a DC coupled low-frequency BMC-coded data channel that reduces the possibilities for RF interference.^[66] Power Delivery protocols have been updated to facilitate USB-C features such as cable ID function, Alternate Mode negotiation, increased V_BUS currents, and V_CONN-powered accessories.

As of USB Power Delivery specification revision 2.0, version 1.2, the six fixed power profiles for power sources have been deprecated.^[67] USB PD Power Rules replace power profiles, defining four normative voltage levels at 5 V, 9 V, 15 V, and 20 V. Instead of six fixed profiles, power supplies may support any maximum source output power from 0.5 W to 100 W.

The USB Power Delivery specification revision 3.0 defines an optional Programmable Power Supply (PPS) protocol that allows granular control over V_BUS output, allowing a voltage range of 3.3 to 21 V in 20 mV steps, and a current specified in 50 mA steps, to facilitate constant-voltage and constant-current charging. Revision 3.0 also adds extended configuration messages and fast role swap and deprecates the BFSK protocol.^{[57]: Table 6.26 [68][69]}

 

The Certified USB Fast Charger logo for USB Type-C charging ports

On January 8, 2018, USB-IF announced "Certified USB Fast Charger" logo for chargers that use "Programmable Power Supply" (PPS) protocol from the USB Power Delivery 3.0 specification.^[70]

In May 2021, the USB PD promoter group launched revision 3.1 of the specification.^[58] Revision 3.1 adds Extended Power Range (EPR) mode which allows higher voltages of 28, 36, and 48 V, providing up to 240 W of power (48 V at 5 A), and the "Adjustable Voltage Supply" (AVS) protocol which allows specifying the voltage from a range of 15 to 48 V in 100 mV steps.^[71][72] Higher voltages require electronically marked EPR cables that support 5 A operation and incorporate mechanical improvements required by the USB Type-C standard rev. 2.1; existing power modes are retroactively renamed Standard Power Range (SPR). In October 2021 Apple introduced a 140 W (28 V 5 A) GaN USB PD charger with new Macbooks,^[73] and in June 2023 Framework introduced a 180 W (36 V 5 A) GaN USB PD charger with the Framework 16.^[74]

In October 2023, the USB PD promoter group launched revision 3.2 of the specification. The AVS protocol now works with the old standard power range (SPR), down to a minimum of 9 V.^{[75]: §10.2.2}

Prior to Power Delivery, mobile phone vendors used custom protocols to exceed the 7.5 W cap on the USB Battery Charging Specification (BCS). For example, Qualcomm's Quick Charge 2.0 is able to deliver 18 W at a higher voltage, and VOOC delivers 20 W at the normal 5 V.^[76] Some of these technologies, such as Quick Charge 4, eventually became compatible with USB PD again.^[77]

Charge controllers

As of Q1, 2024 mainstream USB PD charging controllers support up to 100w through a single port, with a few up to 140w^[78][79] and custom built up to 180w.^[80]

Sleep-and-charge ports

 

A yellow USB port denoting sleep-and-charge

Sleep-and-charge USB ports can be used to charge electronic devices even when the computer that hosts the ports is switched off. Normally, when a computer is powered off the USB ports are powered down. This feature has also been implemented on some laptop docking stations allowing device charging even when no laptop is present.^[81] On laptops, charging devices from the USB port when it is not being powered from AC drains the laptop battery; most laptops have a facility to stop charging if their own battery charge level gets too low.^[82]

On Dell, HP and Toshiba laptops, sleep-and-charge USB ports are marked with the standard USB symbol with an added lightning bolt or battery icon on the right side.^[83] Dell calls this feature PowerShare,^[84] and it needs to be enabled in the BIOS. Toshiba calls it USB Sleep-and-Charge.^[85] On Acer Inc. and Packard Bell laptops, sleep-and-charge USB ports are marked with a non-standard symbol (the letters USB over a drawing of a battery); the feature is called Power-off USB.^[86] Lenovo calls this feature Always On USB.^[87]

Mobile device charger standards

Main article: Universal charger

In China

As of 14 June 2007^[update], all new mobile phones applying for a license in China are required to use a USB port as a power port for battery charging.^[88][89] This was the first standard to use the convention of shorting D+ and D− in the charger.^[90]

OMTP/GSMA Universal Charging Solution

In September 2007, the Open Mobile Terminal Platform group (a forum of mobile network operators and manufacturers such as Nokia, Samsung, Motorola, Sony Ericsson, and LG) announced that its members had agreed on Micro-USB as the future common connector for mobile devices.^[91][92]

The GSM Association (GSMA) followed suit on February 17, 2009,^{[93][94][95][96]} and on April 22, 2009, this was further endorsed by the CTIA – The Wireless Association,^[97] with the International Telecommunication Union (ITU) announcing on October 22, 2009, that it had also embraced the Universal Charging Solution as its "energy-efficient one-charger-fits-all new mobile phone solution," and added: "Based on the Micro-USB interface, UCS chargers will also include a 4-star or higher efficiency rating—up to three times more energy-efficient than an unrated charger."^[98]

EU smartphone power supply standard

In June 2009, the European Commission organized a voluntary Memorandum of Understanding (MoU) to adopt micro-USB as a common standard for charging smartphones marketed in the European Union. The specification was called the common external power supply. The MoU lasted until 2014. The common EPS specification (EN 62684:2010) references the USB Battery Charging Specification and is similar to the GSMA/OMTP and Chinese charging solutions.^[99][100] In January 2011, the International Electrotechnical Commission (IEC) released its version of the (EU's) common EPS standard as IEC 62684:2011.^[101]

In 2022, the Radio Equipment Directive 2022/2380 made USB-C compulsory as a mobile phone charging standard from 2024, and for laptops from 2026.^[102]

Faster-charging standards

A variety of (non-USB) standards support charging devices faster than the USB Battery Charging standard. When a device doesn't recognize the faster-charging standard, generally the device and the charger fall back to the USB battery-charging standard of 5 V at 1.5 A (7.5 W). When a device detects it is plugged into a charger with a compatible faster-charging standard, the device pulls more current or the device tells the charger to increase the voltage or both to increase power (the details vary between standards).^[103]

Such standards include:^[103][104]

• Anker PowerIQ
• Google fast charging
• Huawei SuperCharge
• MediaTek Pump Express
• Motorola TurboPower
• Oppo Super VOOC Flash Charge, are also known as Dash Charge or Warp Charge on OnePlus devices and Dart Charge on Realme devices
• Qualcomm Quick Charge (QC)
• Samsung Adaptive Fast Charging

Non-standard devices

Some USB devices require more power than is permitted by the specifications for a single port. This is common for external hard and optical disc drives, and generally for devices with motors or lamps. Such devices can use an external power supply, which is allowed by the standard, or use a dual-input USB cable, one input of which is for power and data transfer, the other solely for power, which makes the device a non-standard USB device. Some USB ports and external hubs can, in practice, supply more power to USB devices than required by the specification but a standard-compliant device may not depend on this.

In addition to limiting the total average power used by the device, the USB specification limits the inrush current (i.e., the current used to charge decoupling and filter capacitors) when the device is first connected. Otherwise, connecting a device could cause problems with the host's internal power. USB devices are also required to automatically enter ultra low-power suspend mode when the USB host is suspended. Nevertheless, many USB host interfaces do not cut off the power supply to USB devices when they are suspended.^[105]

Some non-standard USB devices use the 5 V power supply without participating in a proper USB network, which negotiates power draw with the host interface. Examples include USB-powered keyboard lights, fans, mug coolers and heaters, battery chargers, miniature vacuum cleaners, and even miniature lava lamps. In most cases, these items contain no digital circuitry, and thus are not standard-compliant USB devices. This may cause problems with some computers, such as drawing too much current and damaging circuitry. Prior to the USB Battery Charging Specification, the USB specification required that devices connect in a low-power mode (100 mA maximum) and communicate their current requirements to the host, which then permits the device to switch into high-power mode.

Some devices, when plugged into charging ports, draw even more power (10 watts) than the Battery Charging Specification allows—the iPad is one such device;^[106] it negotiates the current pull with data pin voltages.^[53] Barnes & Noble Nook Color devices also require a special charger that runs at 1.9 A.^[107]

PoweredUSB

Main article: PoweredUSB

PoweredUSB is a proprietary extension that adds four pins supplying up to 6 A at 5 V, 12 V, or 24 V. It is commonly used in point of sale systems to power peripherals such as barcode readers, credit card terminals, and printers.

See also

• USB adapter
• USB communications

References

1. . June 6, 2011. p. 531. Archived from the original on December 30, 2013. Retrieved April 28, 2019.
2. (PDF). October 20, 2000. Archived from the original (PDF) on April 12, 2015. Retrieved April 28, 2019 – via www.usb.org.
3. "USB connector guide". C2G. from the original on 21 April 2014. Retrieved 2 December 2013.
4. (PDF). USB implementers forum. August 2007. Archived from the original (PDF) on June 11, 2014. Retrieved April 28, 2019.
5. Howse, Brett. "USB Type-C Connector Specifications Finalized". AnandTech. from the original on March 18, 2017. Retrieved April 24, 2017.
6. . usbpinout.net. Archived from the original on 17 June 2014. Retrieved 28 April 2019.
7. "Universal Serial Bus Micro-USB Cables and Connectors Specification" (PDF). USB Implementers Forum. April 4, 2007. (PDF) from the original on November 15, 2015. Retrieved January 31, 2015.
8. . Usb.org. Archived from the original (ZIP) on 19 May 2014. Retrieved 28 April 2019.
9. Quinnell, Richard A (October 24, 1996). "USB: a neat package with a few loose ends". EDN Magazine. Reed. from the original on May 23, 2013. Retrieved February 18, 2013.
10. "What is the Difference between USB Type A and USB Type B Plug/Connector?". from the original on February 7, 2017.
11. (PDF) (Press release). USB Implementers Forum. 27 May 2007. Archived from the original (PDF) on 6 March 2009. Retrieved 13 January 2009.
12. "ID Pin Resistance on Mini B-plugs and Micro B-plugs Increased to 1 Mohm". USB IF Compliance Updates. December 2009. from the original on 20 July 2011. Retrieved 1 March 2010.
13. Universal Serial Bus Cables and Connectors Class Document (PDF), Revision 2.0, USB Implementers Forum, August 2007, p. 6, (PDF) from the original on April 27, 2015, retrieved August 17, 2014
14. "Mobile phones to adopt new, smaller USB connector" (PDF) (Press release). USB Implementers Forum. 4 January 2007. (PDF) from the original on 8 January 2007. Retrieved 8 January 2007.
15. "Micro-USB pinout and list of compatible smartphones and other devices". pinoutsguide.com. from the original on October 10, 2013.
16. . USB Implementers Forum. April 7, 2007. Archived from the original (Zip) on February 7, 2012. Retrieved November 18, 2010. Section 1.3: Additional requirements for a more rugged connector that is durable past 10,000 cycles and still meets the USB 2.0 specification for mechanical and electrical performance was also a consideration. The Mini-USB could not be modified and remain backward compatible to the existing connector as defined in the USB OTG specification.
17. . Open Mobile Terminal Platform. September 17, 2007. Archived from the original on October 15, 2008. Retrieved February 11, 2009.
18. "Universal phone charger standard approved—One-size-fits-all solution will dramatically cut waste and GHG emissions". ITU (press release). Pressinfo. 22 October 2009. from the original on 5 November 2009. Retrieved 4 November 2009.
19. "Commission welcomes new EU standards for common mobile phone charger". Press Releases. Europa. December 29, 2010. from the original on March 19, 2011. Retrieved May 22, 2011.
20. New EU standards for common mobile phone charger (press release), Europa, from the original on 3 January 2011
21. The following 10 biggest mobile phone companies have signed the MoU: Apple, LG, Motorola, NEC, Nokia, Qualcomm, Research In Motion, Samsung, Sony Ericsson, Texas Instruments (press release), Europa, from the original on July 4, 2009
22. "Nice Micro-USB adapter Apple, now sell it everywhere", Giga om, 5 October 2011, from the original on 26 August 2012
23. "Apple's Lightning to Micro-USB adapter now available in US, not just Europe anymore", Engadget, 3 November 2012, from the original on 26 June 2017
24. Howse, Brett (August 12, 2014). "USB Type-C Connector Specifications Finalized". from the original on December 28, 2014. Retrieved December 28, 2014.
25. Hruska, Joel (13 March 2015). "USB-C vs. USB 3.1: What's the difference?". ExtremeTech. from the original on 11 April 2015. Retrieved 9 April 2015.
26. Ngo, Dong (August 22, 2014). . c|net. Archived from the original on March 7, 2015. Retrieved December 28, 2014.
27. . Archived from the original on December 29, 2014. Retrieved December 29, 2014.
28. Smith, Ryan (September 22, 2014). "DisplayPort Alternate Mode for USB Type-C Announced - Video, Power, & Data All Over Type-C". AnandTech. from the original on December 18, 2014. Retrieved December 28, 2014.
29. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.1 (April 3, 2015), section 2.2, page 20
30. Universal Serial Bus Type-C Cable and Connector Specification, Release 2.2. USB Implementers Forum (Technical report). USB 3.0 Promoter Group. October 2022. Retrieved April 12, 2023.
31. "On-The-Go and Embedded Host Supplement to the USB Revision 3.0 Specification" (PDF). USB.org. Revision 1.1. May 10, 2012.
32. . anythingbutipod.com. 30 April 2008. Archived from the original on 13 November 2013. Retrieved 29 October 2013.
33. Lex Friedman (25 February 2013). "Review: Logitech's Ultrathin mini keyboard cover makes the wrong tradeoffs". macworld.com. from the original on 3 November 2013. Retrieved 29 October 2013.
34. . Hantat. May 18, 2009. Archived from the original on December 11, 2011. Retrieved December 12, 2011.
35. (PDF). cablesplususa.com. November 3, 2010. Archived from the original (PDF) on October 11, 2014. Retrieved February 2, 2014.
36. "What is the Maximum Length of a USB Cable?". Techwalla.com. from the original on December 1, 2017. Retrieved November 18, 2017.
37. . USB.org. Archived from the original on January 15, 2014. Retrieved May 22, 2023.
38. Axelson, Jan. "USB 3.0 Developers FAQ". from the original on December 20, 2016. Retrieved October 20, 2016.
39. "USB Type-C Revision 1.0" (PDF). USB 3.0 Promoter Group. March 1, 2021. (PDF) from the original on November 3, 2021. Retrieved November 3, 2021.
40. "USB ECN USB 2.0 VBUS Max Limit". USB-IF. November 3, 2021. from the original on November 3, 2021. Retrieved November 3, 2021.
41. "Battery Charging v1.2 Spec and Adopters Agreement" (PDF (Zipped)). USB.org. March 15, 2015. Table 5-1 Voltages. (PDF (Zipped)) from the original on November 3, 2021. Retrieved November 3, 2021.
42. "USB Power Delivery Specifications 2.0 and 3.1" (PDF (Zipped)). USB.org. October 26, 2021. (PDF (Zipped)) from the original on November 3, 2021. Retrieved November 3, 2021.
43. "USB.org". USB.org. from the original on 19 June 2012. Retrieved 22 June 2010.
44. "Universal Serial Bus 1.1 Specification" (PDF). cs.ucr.edu. 23 September 1998. pp. 150, 158. (PDF) from the original on 2 January 2015. Retrieved 24 November 2014.
45. "Universal Serial Bus 2.0 Specification, Section 7.2.1.3 Low-power Bus-powered Functions" (ZIP). usb.org. 27 April 2000. from the original on 10 September 2013. Retrieved 11 January 2014.
46. "Universal Serial Bus 2.0 Specification, Section 7.2.1.4 High-power Bus-powered Functions" (ZIP). usb.org. 27 April 2000. from the original on 10 September 2013. Retrieved 11 January 2014.
47. . xbitlabs.com. 16 June 2010. Archived from the original on 28 June 2010. Retrieved 9 July 2010.
48. . hitachigst.com. Archived from the original on 15 February 2011. Retrieved 30 March 2012.
49. "USB-IF Compliance Updates". Compliance.usb.org. 1 September 2011. from the original on 3 February 2014. Retrieved 22 January 2014.
50. "Battery Charging Specification, Revision 1.2". USB Implementers Forum. 15 March 2012. from the original on 10 March 2021. Retrieved 13 August 2021.
51. . USB Implementers Forum. April 15, 2009. Archived from the original on March 29, 2014. Retrieved September 23, 2009.
52. "Battery Charging v1.2 Spec and Adopters Agreement" (Zip). USB Implementers Forum. March 15, 2012. from the original on October 6, 2014. Retrieved May 13, 2021.
53. . Lady Ada. 17 May 2011. Archived from the original on 28 March 2012.
54. "Modify a cheap USB charger to feed an iPod, iPhone". 5 October 2011. from the original on 7 October 2011.
55. "PD_1.0" (PDF). (PDF) from the original on April 4, 2016. Retrieved April 27, 2016.
56. "10 Power Rules", Universal Serial Bus Power Delivery Specification revision 2.0, version 1.2, USB Implementers Forum, 25 March 2016, archived from the original on 1 June 2012, retrieved 9 April 2016
57. "10 Power Rules", Universal Serial Bus Power Delivery Specification revision 3.0, version 1.1, USB Implementers Forum, archived from the original on June 1, 2012, retrieved September 5, 2017
58. "10 Power Rules", Universal Serial Bus Power Delivery Specification revision 3.1, version 1.0, USB Implementers Forum, retrieved September 5, 2017
59. Burgess, Rick (April 22, 2013). "USB 3.0 SuperSpeed Update to Eliminate Need for Chargers". TechSpot.
60. "USB 3.0 Promoter Group Announces Availability of USB Power Delivery Specification" (PDF). July 18, 2012. (PDF) from the original on January 20, 2013. Retrieved January 16, 2013.
61. "Edison's revenge". The Economist. October 19, 2013. from the original on October 22, 2013. Retrieved October 23, 2013.
62. "USB Power Delivery — Introduction" (PDF). July 16, 2012. (PDF) from the original on January 23, 2013. Retrieved January 6, 2013.
63. "USB Power Delivery".
64. "USB 3.1 Specification". from the original on June 19, 2012. Retrieved November 11, 2014.
65. "USB Power Delivery v2.0 Specification Finalized - USB Gains Alternate Modes". AnandTech.com.
66. "USB Future Specifications Industry Reviews" (PDF). (PDF) from the original on July 29, 2014. Retrieved August 10, 2014.
67. , Universal Serial Bus Power Delivery Specification revision 2.0, version 1.2, USB Implementers Forum, 25 March 2016, archived from the original on 12 April 2016, retrieved 9 April 2016
68. (PDF). usb.org. USB-IF. October 20, 2016. Archived from the original (PDF) on December 20, 2016.
69. Waters, Deric (July 14, 2016). "USB Power Delivery 2.0 vs 3.0". E2E.TI.com. from the original on July 30, 2017. Retrieved July 30, 2017.
70. "USB-IF Introduces Fast Charging to Expand its Certified USB Charger Initiative" (Press release). January 9, 2018. Retrieved January 10, 2018.
71. USB-PD boosts USB-C power delivery to 240W at 48V. Nick Flaherty, EENews. May 28, 2021
72. USB-C Power Delivery Hits 240W with Extended Power Range. Ganesh T S, Anandtech. May 28, 2021
73. "Teardown of Brand New Apple 140W USB-C GaN Charger". October 30, 2021. Retrieved November 15, 2021.
74. "Framework Laptop 16 Deep Dive - 180W Power Adapter". Framework. Retrieved February 28, 2024.
75. Universal Serial Bus Power Delivery Specification revision 3.2, version 1.0, USB Implementers Forum, retrieved February 13, 2023
76. "How fast can a fast-charging phone charge if a fast-charging phone can charge really fast?". CNet. Retrieved December 4, 2016.
77. "Qualcomm Announces Quick Charge 4: Supports USB Type-C Power Delivery". AnandTech. Retrieved December 13, 2016.
78. "Teardown of Anker 140W PD3.1 USB-C GaN Charger (717 Charger)". October 26, 2022.
79. 140W PD 3.1 Power Adapters, the future of USB C Power Delivery, retrieved March 8, 2024
80. "Framework Laptop 16 Deep Dive - 180W Power Adapter". Framework. Retrieved March 8, 2024.
81. "ThinkPad Ultra Dock". lenovo.com. from the original on September 17, 2016. Retrieved September 16, 2016.
82. "Toshiba NB200 User Manual" (PDF). UK. 1 March 2009. (PDF) from the original on 19 February 2014. Retrieved 26 January 2014.
83. "USB PowerShare Feature". dell.com. 15 September 2019. Retrieved 15 June 2020.
84. "USB PowerShare Feature". dell.com. 5 June 2013. from the original on 8 November 2013. Retrieved 4 December 2013.
85. "USB Sleep-and-Charge Ports". toshiba.com. from the original on 14 December 2014. Retrieved 21 December 2014.
86. "USB Charge Manager". packardbell.com. Retrieved April 25, 2014.
87. "How to configure the system to charge devices over USB port when it is off - idea/Lenovo laptops - NL". support.lenovo.com. Retrieved April 7, 2020.
88. Cai Yan (31 May 2007). "China to enforce universal cell phone charger". EE Times. from the original on 29 September 2007. Retrieved 25 August 2007.
89. The Chinese technical standard: (PDF). Dian yuan (in Chinese). Archived from the original (PDF) on 15 May 2011.
90. Lam, Crystal; Liu, Harry (October 22, 2007). "How to conform to China's new mobile phone interface standards". Wireless Net DesignLine. from the original on May 14, 2014. Retrieved June 22, 2010.
91. "Pros Seem to Outdo Cons in New Phone Charger Standard". News.com. September 20, 2007. Retrieved November 26, 2007.
92. (Press release). OTMP. September 17, 2007. Archived from the original on June 29, 2009. Retrieved November 26, 2007.
93. (Press release). GSM World. Archived from the original on 17 February 2009.
94. . Open Mobile Terminal Platform. February 11, 2009. Archived from the original on March 29, 2009. Retrieved February 11, 2009.
95. . GSM world. Archived from the original on June 26, 2010. Retrieved June 22, 2010.
96. "Meeting the challenge of the universal charge standard in mobile phones". Planet Analog. Archived from the original on September 9, 2012. Retrieved June 22, 2010.
97. (Press release). CTIA. 22 April 2009. Archived from the original on 14 December 2010. Retrieved 22 June 2010.
98. (Press release). ITU. October 22, 2009. Archived from the original on March 27, 2010. Retrieved May 22, 2023.
99. . EU: EC. 29 June 2009. Archived from the original on 23 October 2009. Retrieved 22 June 2010.
100. "Europe gets universal cellphone charger in 2010". Wired. June 13, 2009. from the original on August 18, 2010. Retrieved June 22, 2010.
101. "One size-fits-all mobile phone charger: IEC publishes first globally relevant standard". International Electrotechnical Commission. February 1, 2011. from the original on January 3, 2012. Retrieved February 20, 2012.
102. . European Parliament. April 20, 2022. Archived from the original on April 22, 2022. Retrieved April 20, 2022.
103. Kumar, Ajay; Winkelman, Steven; LeClair, Dave (July 27, 2022). "What Is Fast Charging?". PCMag. Retrieved May 21, 2023.
104. Hill, Simon; Revilla, Andre; Chandler, Simon (July 1, 2021). "How does fast charging work? Here's every single standard compared". Digital Trends. Retrieved August 20, 2022.
105. "Part 2 - Electrical". MQP Electronics. from the original on December 24, 2014. Retrieved December 29, 2014.
106. "Watt to Know About iPhone & iPad Power Adapters | Analysis". The Mac Observer. from the original on December 10, 2011. Retrieved December 12, 2011.
107. . barnesandnoble.com. July 3, 2011. Archived from the original on February 11, 2012.