Strontium titanate

Strontium titanate is an oxide of strontium and titanium with the chemical formula SrTiO₃. At room temperature, it is a centrosymmetric paraelectric material with a perovskite structure. At low temperatures it approaches a ferroelectric phase transition with a very large dielectric constant ~10⁴ but remains paraelectric down to the lowest temperatures measured as a result of quantum fluctuations, making it a quantum paraelectric.^[1] It was long thought to be a wholly artificial material, until 1982 when its natural counterpart—discovered in Siberia and named tausonite—was recognised by the IMA. Tausonite remains an extremely rare mineral in nature, occurring as very tiny crystals. Its most important application has been in its synthesized form wherein it is occasionally encountered as a diamond simulant, in precision optics, in varistors, and in advanced ceramics.

Strontium titanate

Names
Other names Strontium titanium oxide Tausonite STO
Identifiers
CAS Number	12060-59-2^Y
3D model (JSmol)	Interactive image Interactive image
ChemSpider	74801^Y
ECHA InfoCard	100.031.846
EC Number	235-044-1
MeSH	Strontium+titanium+oxide
PubChem CID	82899
UNII	OLH4I98373^Y
CompTox Dashboard (EPA)	DTXSID70893688
InChI InChI=1S/3O.Sr.Ti/q;2*-1;+2;^Y Key: VEALVRVVWBQVSL-UHFFFAOYSA-N^Y InChI=1/3O.Sr.Ti/q;2*-1;+2;/rO3Ti.Sr/c1-4(2)3;/q-2;+2 Key: VEALVRVVWBQVSL-VUHNDFTMAE
SMILES [Sr++].[O-][Ti]([O-])=O [Sr+2].[O-][Ti]([O-])=O
Properties
Chemical formula	SrTiO 3
Molar mass	183.49 g/mol
Appearance	White, opaque crystals
Density	5.11 g/cm^3
Melting point	2,080 °C (3,780 °F; 2,350 K)
Solubility in water	insoluble
Refractive index (nD)	2.394
Structure
Crystal structure	Cubic Perovskite
Space group	Pm3m, No. 221
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa). Y verify (what is ^YN ?) Infobox references

The name tausonite was given in honour of Lev Vladimirovich Tauson (1917–1989), a Russian geochemist. Disused trade names for the synthetic product include strontium mesotitanate, Diagem, and Marvelite. This product is currently being marketed for its use in jewelry under the name Fabulite.^[2] Other than its type locality of the Murun Massif in the Sakha Republic, natural tausonite is also found in Cerro Sarambi, Concepción department, Paraguay; and along the Kotaki River of Honshū, Japan.^[3][4]

Properties

 

Atomic resolution image of SrTiO₃ acquired using a Scanning Transmission Electron Microscope (STEM) and a high angle annular dark field (HAADF) detector. Brighter spots are columns of atoms containing Sr, and darker spots contain Ti. Columns containing only O atoms are not visible.

 

Structure of SrTiO₃. The red spheres are oxygens, blue are Ti⁴⁺ cations, and the green ones are Sr²⁺.

SrTiO₃ has an indirect band gap of 3.25 eV and a direct gap of 3.75 eV ^[5] in the typical range of semiconductors. Synthetic strontium titanate has a very large dielectric constant (300) at room temperature and low electric field. It has a specific resistivity of over 10⁹ Ω-cm for very pure crystals.^[6] It is also used in high-voltage capacitors. Introducing mobile charge carriers by doping leads to Fermi-liquid metallic behavior already at very low charge carrier densities.^[7] At high electron densities strontium titanate becomes superconducting below 0.35 K and was the first insulator and oxide discovered to be superconductive.^[8]

Strontium titanate is both much denser (specific gravity 4.88 for natural, 5.13 for synthetic) and much softer (Mohs hardness 5.5 for synthetic, 6–6.5 for natural) than diamond. Its crystal system is cubic and its refractive index (2.410—as measured by sodium light, 589.3 nm) is nearly identical to that of diamond (at 2.417), but the dispersion (the optical property responsible for the "fire" of the cut gemstones) of strontium titanate is 4.3x that of diamond, at 0.190 (B–G interval). This results in a shocking display of fire compared to diamond and diamond simulants such as YAG, GAG, GGG, Cubic Zirconia, and Moissanite.^[3][4]

Synthetics are usually transparent and colourless, but can be doped with certain rare earth or transition metals to give reds, yellows, browns, and blues. Natural tausonite is usually translucent to opaque, in shades of reddish brown, dark red, or grey. Both have an adamantine (diamond-like) lustre. Strontium titanate is considered extremely brittle with a conchoidal fracture; natural material is cubic or octahedral in habit and streaks brown. Through a hand-held (direct vision) spectroscope, doped synthetics will exhibit a rich absorption spectrum typical of doped stones. Synthetic material has a melting point of ca. 2080 °C (3776 °F) and is readily attacked by hydrofluoric acid.^[3][4] Under extremely low oxygen partial pressure, strontium titanate decomposes via incongruent sublimation of strontium well below the melting temperature.^[9]

At temperatures lower than 105 K, its cubic structure transforms to tetragonal.^[10] Its monocrystals can be used as optical windows and high-quality sputter deposition targets.

 

Strontium titanate single crystal substrates (5x5x0.5mm). The transparent substrate (left) is pure SrTiO₃ and the black substrate is doped with 0.5% (weight) of niobium

SrTiO₃ is an excellent substrate for epitaxial growth of high-temperature superconductors and many oxide-based thin films. It is particularly well known as the substrate for the growth of the lanthanum aluminate-strontium titanate interface. Doping strontium titanate with niobium makes it electrically conductive, being one of the only conductive commercially available single crystal substrates for the growth of perovskite oxides. Its bulk lattice parameter of 3.905Å makes it suitable as the substrate for the growth of many other oxides, including the rare-earth manganites, titanates, lanthanum aluminate (LaAlO₃), strontium ruthenate (SrRuO₃) and many others. Oxygen vacancies are fairly common in SrTiO₃ crystals and thin films. Oxygen vacancies induce free electrons in the conduction band of the material, making it more conductive and opaque. These vacancies can be caused by exposure to reducing conditions, such as high vacuum at elevated temperatures.

High-quality, epitaxial SrTiO₃ layers can also be grown on silicon without forming silicon dioxide, thereby making SrTiO₃ an alternative gate dielectric material. This also enables the integration of other thin film perovskite oxides onto silicon.^[11]

SrTiO₃ has been shown to possess persistent photoconductivity where exposing the crystal to light will increase its electrical conductivity by over 2 orders of magnitude. After the light is turned off, the enhanced conductivity persists for several days, with negligible decay.^[12][13]

Due to the significant ionic and electronic conduction of SrTiO₃, it is potent to be used as the mixed conductor.^[14]

Synthesis

 

A plate cut out of synthetic SrTiO₃ crystal

Synthetic strontium titanate was one of several titanates patented during the late 1940s and early 1950s; other titanates included barium titanate and calcium titanate. Research was conducted primarily at the National Lead Company (later renamed NL Industries) in the United States, by Leon Merker and Langtry E. Lynd. Merker and Lynd first patented the growth process on February 10, 1953; a number of refinements were subsequently patented over the next four years, such as modifications to the feed powder and additions of colouring dopants.

A modification to the basic Verneuil process (also known as flame-fusion) is the favoured method of growth. An inverted oxy-hydrogen blowpipe is used, with feed powder mixed with oxygen carefully fed through the blowpipe in the typical fashion, but with the addition of a third pipe to deliver oxygen—creating a tricone burner. The extra oxygen is required for successful formation of strontium titanate, which would otherwise fail to oxidize completely due to the titanium component. The ratio is ca. 1.5 volumes of hydrogen for each volume of oxygen. The highly purified feed powder is derived by first producing titanyl double oxalate salt (SrTiO(C₂O₄)₂ · 2 H₂O) by reacting strontium chloride (SrCl₂) and oxalic acid ((COOH)₂ · 2 H₂O) with titanium tetrachloride (TiCl₄). The salt is washed to completely eliminate chloride, heated to 1000 °C in order to produce a free-flowing granular powder of the required composition, and is then ground and sieved to ensure all particles are between 0.2–0.5 micrometres in size.^[15]

The feed powder falls through the oxyhydrogen flame, melts, and lands on a rotating and slowly descending pedestal below. The height of the pedestal is constantly adjusted to keep its top at the optimal position below the flame, and over a number of hours the molten powder cools and crystallises to form a single pedunculated pear or boule crystal. This boule is usually no larger than 2.5 centimetres in diameter and 10 centimetres long; it is an opaque black to begin with, requiring further annealing in an oxidizing atmosphere in order to make the crystal colourless and to relieve strain. This is done at over 1000 °C for 12 hours.^[15]

Thin films of SrTiO₃ can be grown epitaxially by various methods, including pulsed laser deposition, molecular beam epitaxy, RF sputtering and atomic layer deposition. As in most thin films, different growth methods can result in significantly different defect and impurity densities and crystalline quality, resulting in a large variation of the electronic and optical properties.

Use as a diamond simulant

Its cubic structure and high dispersion once made synthetic strontium titanate a prime candidate for simulating diamond. Beginning c. 1955, large quantities of strontium titanate were manufactured for this sole purpose. Strontium titanate was in competition with synthetic rutile ("titania") at the time, and had the advantage of lacking the unfortunate yellow tinge and strong birefringence inherent to the latter material. While it was softer, it was significantly closer to diamond in likeness. Eventually, however, both would fall into disuse, being eclipsed by the creation of "better" simulants: first by yttrium aluminium garnet (YAG) and followed shortly after by gadolinium gallium garnet (GGG); and finally by the (to date) ultimate simulant in terms of diamond-likeness and cost-effectiveness, cubic zirconia.^[16]

Despite being outmoded, strontium titanate is still manufactured and periodically encountered in jewellery. It is one of the most costly of diamond simulants, and due to its rarity collectors may pay a premium for large i.e. >2 carat (400 mg) specimens. As a diamond simulant, strontium titanate is most deceptive when mingled with melée i.e. <0.20 carat (40 mg) stones and when it is used as the base material for a composite or doublet stone (with, e.g., synthetic corundum as the crown or top of the stone). Under the microscope, gemmologists distinguish strontium titanate from diamond by the former's softness—manifested by surface abrasions—and excess dispersion (to the trained eye), and occasional gas bubbles which are remnants of synthesis. Doublets can be detected by a join line at the girdle ("waist" of the stone) and flattened air bubbles or glue visible within the stone at the point of bonding.^[17][18][19]

Use in radioisotope thermoelectric generators

Due to its high melting point and insolubility in water, strontium titanate has been used as a strontium-90-containing material in radioisotope thermoelectric generators (RTGs), such as the US Sentinel and Soviet Beta-M series.^[20][21] As strontium-90 has a high fission product yield and is easily extracted from spent nuclear fuel, Sr-90 based RTGs can in principle be produced cheaper than those based on plutonium-238 or other radionuclides which have to be produced in dedicated facilities. However, due to the lower power density (~0.45W _thermal per gram of Strontium-90-Titanate) and half life, space based applications, which put a particular premium on low weight, high reliability and longevity prefer Plutonium-238. Terrestrial off-grid applications of RTGs meanwhile have been largely phased out due to concern over orphan sources and the decreasing price and increasing availability of solar panels, small wind turbines, chemical battery storage and other off-grid power solutions.

Use in solid oxide fuel cells

Strontium titanate's mixed conductivity has attracted attention for use in solid oxide fuel cells (SOFCs). It demonstrates both electronic and ionic conductivity which is useful for SOFC electrodes because there is an exchange of gas and oxygen ions in the material and electrons on both sides of the cell.

${\displaystyle {\ce {H2 + O^2- -> H2O + 2e-}}}$  (anode)

${\displaystyle {\ce {1/2O2 + 2e- -> O^2-}}}$  (cathode)

Strontium titanate is doped with different materials for use on different sides of a fuel cell. On the fuel side (anode), where the first reaction occurs, it is often doped with lanthanum to form lanthanum-doped strontium titanate (LST). In this case, the A-site, or position in the unit cell where strontium usually sits, is sometimes filled by lanthanum instead, this causes the material to exhibit n-type semiconductor properties, including electronic conductivity. It also shows oxygen ion conduction due to the perovskite structure tolerance for oxygen vacancies. This material has a thermal coefficient of expansion similar to that of the common electrolyte yttria-stabilized zirconia (YSZ), chemical stability during the reactions which occur at fuel cell electrodes, and electronic conductivity of up to 360 S/cm under SOFC operating conditions.^[22] Another key advantage of these LST is that it shows a resistance to sulfur poisoning, which is an issue with the currently used nickel - ceramic (cermet) anodes.^[23]

Another related compound is strontium titanium ferrite (STF) which is used as a cathode (oxygen-side) material in SOFCs. This material also shows mixed ionic and electronic conductivity which is important as it means the reduction reaction which happens at the cathode can occur over a wider area.^[24] Building on this material by adding cobalt on the B-site (replacing titanium) as well as iron, we have the material STFC, or cobalt-substituted STF, which shows remarkable stability as a cathode material as well as lower polarization resistance than other common cathode materials such as lanthanum strontium cobalt ferrite. These cathodes also have the advantage of not containing rare earth metals which make them cheaper than many of the alternatives.^[25]

See also

• Calcium copper titanate

References

1. K. A. Muller & H. Burkard (1979). "SrTiO₃: An intrinsic quantum paraelectric below 4 K". Phys. Rev. B. 19 (7): 3593–3602. Bibcode:1979PhRvB..19.3593M. doi:10.1103/PhysRevB.19.3593.
2. Mottana, Annibale (March 1986). "Una brillante sintesi". Scienza e Dossier (in Italian). Giunti. 1 (1): 9.
3. "Tausonite". Webmineral. Retrieved 2009-06-06.
4. "Tausonite". Mindat. Retrieved 2009-06-06.
5. K. van Benthem, C. Elsässer and R. H. French (2001). "Bulk electronic structure of SrTiO₃: Experiment and theory". Journal of Applied Physics. 90 (12): 6156. Bibcode:2001JAP....90.6156V. doi:10.1063/1.1415766. S2CID 54065614.
6. . ESPI Metals. ESPICorp. Archived from the original on 2015-09-24.
7. Xiao Lin, Benoît Fauqué, Kamran Behnia (2015). "Scalable T² resistivity in a small single-component Fermi surface". Science. 349 (6251): 945–8. arXiv:1508.07812. Bibcode:2015Sci...349..945L. doi:10.1126/science.aaa8655. PMID 26315430. S2CID 148360.{{cite journal}}: CS1 maint: multiple names: authors list (link)
8. Koonce, C. S.; Cohen, Marvin L. (1967). "Superconducting Transition Temperatures of Semiconducting SrTiO3". Phys. Rev. 163 (2): 380. Bibcode:1967PhRv..163..380K. doi:10.1103/PhysRev.163.380.
9. C. Rodenbücher; P. Meuffels; W. Speier; M. Ermrich; D. Wrana; F. Krok; K. Szot (2017). "Stability and Decomposition of Perovskite-Type Titanates upon High-Temperature Reduction". Phys. Status Solidi RRL. 11 (9): 1700222. Bibcode:2017PSSRR..1100222R. doi:10.1002/pssr.201700222. S2CID 102882984.
10. L. Rimai & G. A. deMars (1962). "Electron Paramagnetic Resonance of Trivalent Gadolinium Ions in Strontium and Barium Titanates". Phys. Rev. 127 (3): 702. Bibcode:1962PhRv..127..702R. doi:10.1103/PhysRev.127.702.
11. R. A. McKee; F. J. Walker & M. F. Chisholm (1998). "Crystalline Oxides on Silicon: The First Five Monolayers". Phys. Rev. Lett. 81 (14): 3014. Bibcode:1998PhRvL..81.3014M. doi:10.1103/PhysRevLett.81.3014.
12. Tarun, Marianne C.; Selim, Farida A.; McCluskey, Matthew D. (2013). "Persistent Photoconductivity in Strontium Titanate". Physical Review Letters. Department of Physics and Astronomy, Washington State University, Pullman, Washington. 111 (18): 187403. Bibcode:2013PhRvL.111r7403T. doi:10.1103/PhysRevLett.111.187403. PMID 24237562. Retrieved 2013-11-18.
13. "Light Exposure Increases Crystal's Electrical Conductivity 400-fold [VIDEO]". Nature World News. Retrieved 2013-11-18.
14. "Mixed conductors". Max Planck institute for solid state research. Retrieved 16 September 2016.
15. H. J. Scheel & P. Capper (2008). Crystal growth technology: from fundamentals and simulation to large-scale production. Wiley-VCH. p. 431. ISBN 978-3-527-31762-2.
16. R. W. Hesse (2007). Jewelrymaking through history: an encyclopedia. Greenwood Publishing Group. p. 73. ISBN 978-0-313-33507-5.
17. Nassau, K. (1980). Gems made by man. Santa Monica, California: Gemological Institute of America. pp. 214–221. ISBN 0-87311-016-1.
18. O'Donoghue, M. (2002). Synthetic, imitation & treated gemstones. Great Britain: Elsevier Butterworth-Heinemann. pp. 34, 65. ISBN 0-7506-3173-2.
19. Read, P. G. (1999). Gemmology, second edition. Great Britain: Butterworth-Heinemann. pp. 173, 176, 177, 293. ISBN 0-7506-4411-7.
20. "Power Sources for Remote Arctic Applications" (PDF). Washington, DC: U.S. Congress, Office of Technology Assessment. June 1994. OTA-BP-ETI-129.
21. Standring, WJF; Selnæs, ØG; Sneve, M; Finne, IE; Hosseini, A; Amundsen, I; Strand, P (2005), (PDF), Østerås: Norwegian Radiation Protection Authority, archived from the original (PDF) on 2016-03-03, retrieved 2013-12-04
22. Marina, O (2002). "Thermal, electrical, and electrocatalytical properties of lanthanum-doped strontium titanate". Solid State Ionics. 149 (1–2): 21–28. doi:10.1016/S0167-2738(02)00140-6.
23. Gong, Mingyang; Liu, Xingbo; Trembly, Jason; Johnson, Christopher (2007). "Sulfur-tolerant anode materials for solid oxide fuel cell application". Journal of Power Sources. 168 (2): 289–298. Bibcode:2007JPS...168..289G. doi:10.1016/j.jpowsour.2007.03.026.
24. Jung, WooChul; Tuller, Harry L. (2009). "Impedance study of SrTi1−xFexO3−δ (x=0.05 to 0.80) mixed ionic-electronic conducting model cathode". Solid State Ionics. 180 (11–13): 843–847. doi:10.1016/j.ssi.2009.02.008.
25. Zhang, Shan-Lin; Wang, Hongqian; Lu, Matthew Y.; Zhang, Ai-Ping; Mogni, Liliana V.; Liu, Qinyuan; Li, Cheng-Xin; Li, Chang-Jiu; Barnett, Scott A. (2018). "Cobalt-substituted SrTi _0.3 Fe _0.7 O _3−δ : a stable high-performance oxygen electrode material for intermediate-temperature solid oxide electrochemical cells". Energy & Environmental Science. 11 (7): 1870–1879. doi:10.1039/C8EE00449H. hdl:11336/99985.

External links

• An electron micrograph of strontium titanate, as artwork entitled "Strontium" at the DeYoung Museum in San Francisco 2013-10-22 at the Wayback Machine