LP record

This article is about vinyl records. For music albums in general, see Album.

"Long Play" redirects here. For other uses, see Long Play (disambiguation).

"Long Player" redirects here. For the album by the Faces, see Long Player (album).

For the American singer-songwriter, see LP (singer).

The LP (from "long playing"^[1] or "long play") is an analog sound storage medium, a phonograph record format characterized by: a speed of 33+1⁄3 rpm; a 12- or 10-inch (30- or 25-cm) diameter; use of the "microgroove" groove specification; and a vinyl (a copolymer of vinyl chloride acetate) composition disk. Introduced by Columbia in 1948, it was soon adopted as a new standard by the entire record industry. Apart from a few relatively minor refinements and the important later addition of stereophonic sound, it remained the standard format for record albums (during a period in popular music known as the album era)^[2] until its gradual replacement from the 1980s to the early 2000s, first by cassettes, then by compact discs, and finally by digital music distribution. Beginning in the late 2000s, the LP has experienced a resurgence in popularity.^[3]

LP

A 12-inch LP vinyl record
Media type	Audio playback
Encoding	Analog groove modulation
Capacity	Originally 23 minutes per side, later increased by several minutes, much longer possible with very low signal level
Read mechanism	Microgroove stylus (maximum tip radius 0.001 in or 25 μm)
Developed by	Columbia Records
Dimensions	12 in (30 cm), 10 in (25 cm), 90–240 g (3.2–8.5 oz)
Usage	Audio storage
Released	1948

Format advantages

At the time the LP was introduced, nearly all phonograph records for home use were made of an abrasive shellac compound which resulted in noisy playback; they had much larger grooves, and played at approximately 78 RPM, limiting the playing time of a 12-inch diameter record to less than five minutes per side. The new product was a 12 or 10-inch (30 or 25 cm) fine-grooved disc made of PVC ("vinyl") and played with a smaller-tipped "microgroove" stylus at a speed of 33+1⁄3 rpm. Each side of a 12-inch LP can play for about 22 minutes.^[4][5] Only the microgroove standard was new, as both vinyl and the 33+1⁄3 rpm speed had been used for special purposes for many years, as well as in one unsuccessful earlier attempt by RCA Victor to introduce a long-playing record for home use.^[6]

Although the LP was suited to classical music because of its extended continuous playing time, it also allowed a collection of ten or more pop music recordings to be put on a single disc. Previously such collections, as well as longer classical music broken up into several parts, had been sold as sets of 78 rpm records in a specially imprinted "record album" consisting of individual record sleeves bound together in book form. The use of the word "album" persisted for the one-disc LP equivalent.^[5]

History

See also: Phonograph record

Soundtrack discs

 

Neumann lathe with SX-74 cutting head

 

Neumann lathe

The prototype of the LP was the soundtrack disc used by the Vitaphone motion picture sound system, developed by Western Electric and introduced in 1926. For soundtrack purposes, the less-than-five minutes of playing time of each side of a conventional 12-inch 78 rpm disc was not acceptable. The sound had to play continuously for at least 11 minutes, long enough to accompany a full 1,000-foot (300 m) reel of 35 mm film projected at 24 frames per second. The disc diameter was increased to 16 inches (40 cm) and the speed was reduced to 33+1⁄3 revolutions per minute. Unlike their microgooved LP descendants, they were made with the same large "standard groove" used by 78s.^[7]

Unlike conventional records, the groove started at the inside of the recorded area near the label and proceeded outward toward the edge.^[8] Like 78s, early soundtrack discs were pressed in an abrasive shellac compound and played with a single-use steel needle held in a massive electromagnetic pickup with a tracking force of 2 ounce-force (0.55 N). A new needle was used each time the film and disc were played.^[9]

By mid-1931 all motion picture studios were recording on optical soundtracks, but sets of soundtrack discs, mastered by dubbing from the optical tracks and scaled down to 12 inches to cut costs, were made as late as 1936 for distribution to theaters still equipped with disc-only sound projectors.^[10]

Radio transcription discs

From 1928 onward, syndicated radio programming was distributed on 78 rpm discs. The desirability of longer continuous playing time soon led to the adoption of the Vitaphone soundtrack disc format. Beginning in about 1930, 16-inch 33+1⁄3 rpm discs playing about 15 minutes per side were used for most of these "electrical transcriptions".^[11]

Longer programs, which required several disc sides, pioneered the system of recording odd-numbered sides inside-out and even-numbered sides outside-in so that the sound quality would match from the end of one side to the start of the next. Although a pair of turntables was used to avoid any pauses for disc-flipping, the sides had to be pressed and arranged so that no disc being played had to be turned over to play the next side in the sequence. For example, a three-disc set designed for manual sequencing would have the sides labeled 1–2, 3–4 and 5–6, and the listener would manually flip each disc as the side ended; for an automatic record changer turntable, the sequencing would be 1–6, 2–5 and 3–4, with the listener flipping over the stack of discs once the third side ended; with broadcast sequence, the ordering would be 1–4, 2–5 and 3–6 so that the studio engineer could play side 1 on one turntable, segue directly into side 2 on a second turntable, and then queue up side 3 on the first turntable.^[12]

Some transcriptions were recorded with a vertically modulated "hill and dale" groove, also known as vertical cut recording. This was found to allow deeper bass (because turntable rumble was laterally modulated in early radio station turntables) and also an extension of the high-end frequency response.^[13]

Initially, transcription discs were pressed only in shellac, but by 1932 pressings in RCA Victor's vinyl-based "Victrolac" were appearing. Other plastics were sometimes used. By the late 1930s, vinyl was standard for nearly all kinds of pressed discs except ordinary commercial 78s, which continued to be made of shellac.^{[citation needed]}

Beginning in the mid-1930s, one-off 16-inch 33+1⁄3 rpm lacquer discs were used by radio networks to archive recordings of their live broadcasts, and by local stations to delay the broadcast of network programming or to prerecord their own productions.^{[citation needed]}

In the late 1940s, magnetic tape recorders were adopted by the networks to pre-record shows or repeat them for airing in different time zones, but 16-inch vinyl pressings continued to be used into the early 1960s for non-network distribution of prerecorded programming. Use of the LP microgroove standard began in the late 1950s, and in the 1960s the size of discs was reduced to 12 inches, becoming physically indistinguishable from ordinary LPs.^{[citation needed]}

Unless the quantity required was very small, pressed discs were a more economical medium for distributing high-quality audio than tape, and CD mastering was, in the early years of that technology, very expensive, so the use of LP-format transcription discs continued into the 1990s. The King Biscuit Flower Hour is a late example, as are Westwood One's The Beatle Years and Doctor Demento programs, which were sent to stations on LP at least through 1992.^[14]

RCA Victor

RCA Victor introduced an early version of a long-playing record for home use in September 1931. These "Program Transcription" discs, as Victor called them, played at 33+1⁄3 rpm and used a somewhat finer and more closely spaced groove than typical 78s. They were to be played with a special "Chromium Orange" chrome-plated steel needle. The 10-inch discs, mostly used for popular and light classical music, were normally pressed in shellac, but the 12-inch discs, mostly used for "serious" classical music, were pressed in Victor's new vinyl-based "Victrolac" compound, which provided a much quieter playing surface. These records could hold up to 15 minutes per side. Beethoven's Fifth Symphony, performed by the Philadelphia Orchestra under Leopold Stokowski, was the first 12-inch recording issued.^[15][16][17] Compton Pakensham, reviewing the event in The New York Times wrote, "What we were not prepared for was the quality of reproduction...incomparably fuller."^[16]

However, many of the subsequent issues were not new recordings but simply dubs made from existing 78 rpm record sets. The dubs were audibly inferior to the original 78s. Two-speed turntables with the 33+1⁄3 rpm speed were included only on expensive high-end machines, which sold in very small numbers, and most people had little money to spend on groceries, let alone phonograph records in the depths of the Great Depression. Record sales in the US had dropped from a high of 105.6 million records sold in 1921 to 5.5 million in 1933 because of competition from radio and the effects of the Depression. Few if any new Program Transcriptions were recorded after 1933, and two-speed turntables soon disappeared from RCA Victor's phonographs. Except for a few recordings of background music for funeral parlors, the last of the issued titles had been purged from the Victor record catalog by the end of the decade. The failure of the new product left RCA Victor with a low opinion of the prospects for any sort of long-playing record, influencing product development decisions during the coming decade.^{[citation needed]}

Columbia

CBS Laboratories head research scientist Peter Goldmark led Columbia's team to develop a phonograph record that would hold at least 20 minutes per side.^[18] Although Goldmark was the chief scientist who selected the team, he delegated most of the experimental work to William S. Bachman, whom Goldmark had lured from General Electric, and Howard H. Scott.^[19]

Research began in 1939, was suspended during World War II, and then resumed in 1945.^[20] Columbia Records unveiled the LP at a press conference in the Waldorf Astoria on June 18, 1948, in two formats: 10 inches (25 centimetres) in diameter, matching that of 78 rpm singles, and 12 inches (30 centimetres) in diameter.^[20][21][22] The initial release of 101 recordings were: 58 12-inch classical LPs (ML 4001 to 4057, ML 4071), 12 10-inch classics (ML 2001 to 2012), twelve 12-inch light classic /ML 4058 - 4067, ML 4069, ML 4070/, eight 10-inch light classic /ML 2013 - ML 2019/ and eleven 10-inch popular numbers (CL 6001 to 6011). According to the Columbia's Initial LP Catalog, published in Billboard on 3.07.1948, all classical LPs were organized in alphabetical order of composers. So, this list is opened by ML 4002 with Bach's Concerto in D minor for 2 violins and orchestra by Adolf Busch and Frances Magnes, with the Busch Chamber Players and Concerto No. 2 in E major by Adolf Busch, with the Busch Chamber Players. Columbia may have planned for the album ML 4001 to be the LP opening the initial list of 101 LPs. However, Bach's A minor Violin Concerto by Tibor Varga, foreseen for Side A, could not be released on LP, because of some contractual reasons, probably. So, without Bach, with Mendelssohn, ML 4001 landed in alphabetical list under M like Mendelsson.

Public reception

When the LP was introduced in 1948, the 78 was the conventional format for phonograph records. By 1952, 78s still accounted for slightly more than half of the units sold in the United States, and just under half of the dollar sales. The 45, oriented toward the single song, accounted for just over 30% of unit sales and just over 25% of dollar sales. The LP represented not quite 17% of unit sales and just over 26% of dollar sales.^[23]

Ten years after their introduction, the share of unit sales for LPs in the US was almost 25%, and of dollar sales 58%. Most of the remainder was taken up by the 45; 78s accounted for only 2% of unit sales and 1% of dollar sales.^[24]

The popularity of the LP ushered in the "Album Era" of English-language popular music, beginning in the late 1950s, as performers took advantage of the longer playing time to create coherent themes or concept albums. "The rise of the LP as a form—as an artistic entity, as they used to say—has complicated how we perceive and remember what was once the most evanescent of the arts", Robert Christgau wrote in Christgau's Record Guide: Rock Albums of the Seventies (1981). "The album may prove a '70s totem—briefer configurations were making a comeback by decade's end. But for the '70s it will remain the basic musical unit, and that's OK with me. I've found over the years that the long-playing record, with its twenty-minute sides and four-to-six compositions/performances per side, suits my habits of concentration perfectly."^[25]

Although the popularity of LPs began to decline in the late 1970s with the advent of Compact Cassettes, and later compact discs, the LP survives as a format to the present day. Vinyl LP records enjoyed a resurgence in the early 2010s.^[26] Vinyl sales in the UK reached 2.8 million in 2012.^[27] US vinyl sales in 2017 reached 15.6 million and 27 million for 2020.^[28]

Competing formats

The LP was soon confronted by the "45", a 7-inch (180 mm) diameter fine-grooved vinyl record playing at 45 rpm, introduced by RCA Victor in 1949. To compete with the LP, boxed album sets of 45s were issued, along with EP (extended play) 45s, which squeezed two or even three selections onto each side. Despite intense marketing efforts by RCA Victor, the 45 ultimately succeeded only in replacing the 78 as the preferred format for singles.^{[citation needed]}

The "last hurrah" for the 78 rpm record in the US was the microgroove 78 series pressed for the Audiophile label (Ewing Nunn, Saukville, Wis.) in the early 1950s. This series was labeled AP-1 through about AP-40, pressed on grainless red vinyl. Today AP-1 through AP-5 are very scarce. By very tightly packing the fine groove, a playing time of 17 minutes per side was achieved. Within a couple of years Audiophile switched to 33+1⁄3.^{[citation needed]}

Reel-to-reel magnetic tape recorders posed a new challenge to the LP in the 1950s, but the higher cost of pre-recorded tapes was one of several factors that confined tape to a niche market. Cartridge and cassette tapes were more convenient and less expensive than reel-to-reel tapes, and they became popular for use in automobiles beginning in the mid-1960s. The LP was not seriously challenged as the primary medium for listening to recorded music at home until the 1970s, however, when the audio quality of the cassette was greatly improved by better tape formulations and noise-reduction systems. By 1983, cassettes were outselling LPs in the US.^[29]

The Compact Disc (CD) was introduced in 1982. It offered a recording that was, theoretically, completely noiseless and not audibly degraded by repeated playing or slight scuffs and scratches. At first, the much higher prices of CDs and CD players limited their target market to affluent early adopters and audiophiles; but prices came down, and by 1988 CDs outsold LPs. The CD became the top-selling format, over cassettes, in 1992.^[29]

Along with phonograph records in other formats, some of which were made of other materials, LPs are now widely referred to simply as "vinyl". Since the late 1990s there has been a vinyl revival.^[30] Demand has increased in niche markets, particularly among audiophiles, DJs, and fans of indie music, but most music sales as of 2018 came from online downloads and online streaming because of their availability, convenience, and price.^[28]

Playing time

With the advent of sound film or "talkies", the need for greater storage space made 33+1⁄3 rpm records more appealing. Soundtracks – played on records synchronized to movie projectors in theatres – could not fit onto the mere five minutes per side that 78s offered. When initially introduced, 12-inch LPs played for a maximum of about 23 minutes per side, 10-inch records for around 15.^{[citation needed]} They were not an immediate success, however, as they were released during the height of the Great Depression, and seemed frivolous to the many impoverished of the time. It wasn't until "microgroove" was developed by Columbia Records in 1948 that Long Players (LPs) reached their maximum playtime, which has continued to modern times.^[31]

Economics and tastes initially determined which kind of music was available on each format. Recording company executives believed upscale classical music fans would be eager to hear a Beethoven symphony or a Mozart concerto without having to flip over multiple, four-minute-per-side 78s, and that pop music fans, who were used to listening to one song at a time, would find the shorter time of the 10-inch LP sufficient. As a result, the 12-inch format was reserved solely for higher-priced classical recordings and Broadway shows. Popular music continued to appear only on 10-inch records.^{[citation needed]}

Their beliefs were wrong. By the mid-1950s, the 10-inch LP, like its similarly sized 78 rpm cousin, lost the format war and was discontinued. Ten-inch records briefly reappeared as mini-LPs in the late 1970s and early 1980s in the United States and Australia as a marketing alternative.^[32]

Exceptions

See also: Unusual types of gramophone records § Unusually long playing times

In 1952, Columbia Records introduced "extended-play" LPs that played for as long as 52 minutes, or 26 minutes per side.^{[citation needed]} These were used mainly for the original cast albums of Broadway musicals, such as Kiss Me, Kate and My Fair Lady, or to fit an entire play, such as the 1950 production of Don Juan in Hell, onto two LPs. The 52-minute playing time remained rare, however, because of mastering limitations, and most LPs continued to be issued with a 30- to 45-minute playing time.^{[citation needed]}

A small number of albums exceeded the 52-minute limit. These records had to be cut with much narrower spacing between the grooves, which allowed for a smaller dynamic range on the records, and meant that playing the record with a worn needle could damage the record. It also resulted in a much quieter sound with increased surface noise. The list of long-playing vinyl records includes the 90-minute 1976 LP 90 Minutes with Arthur Fiedler and the Boston Pops, made by Radio Shack;^[33] Genesis' Duke, with each side exceeding 27 minutes; Bob Dylan's 1976 album Desire, with side two lasting almost thirty minutes; Def Leppard's 1987 album Hysteria, with each side exceeding 30 minutes; Iron Maiden's 1984 release Powerslave and its follow up Somewhere in Time both required this special manufacturing, as each surpassed the 52 minute maximum; Todd Rundgren's 1975 album Initiation, totaling 67 min 32 s over two sides; Paul's Boutique by the Beastie Boys; and André Previn's Previn Plays Gershwin, with the London Symphony Orchestra, whose sides each exceeded 30 minutes;^[34] side two of Pink Floyd's Atom Heart Mother and both sides of the Division Bell and Wings' Greatest all exceed 28 minutes. Finally, several recordings of Beethoven's Ninth Symphony were reissued on single discs; these LPs contained about 35 minutes on each side, with the third movement split into two parts.^{[citation needed]}

Spoken word and comedy albums require a smaller dynamic range compared to musical records. Therefore, they can be cut with narrower spaces between the grooves. The Comic Strip, released by Springtime Records in 1981, has a side A lasting 38 min 4 s, and a side B lasting 31 min 8 s, for a total of 69 min 12 s.^{[citation needed]}

Changers

Turntables called automatic record changers could play records stacked vertically on a spindle. This arrangement encouraged the production of multiple-record sets in automatic sequence. A two-record set had Side 1 and Side 4 on one record, and Side 2 and Side 3 on the other, so the first two sides could play in a changer without the listener's intervention. An alternative type of record changer pushed the played disc off the turntable into a hopper, instead of having discs drop on top of each other. Then the stack was flipped over. Larger boxed sets used appropriate automatic sequencing (1–8, 2–7, 3–6, 4–5) to allow continuous playback, but this created difficulties when searching for an individual track.^[35]

Disadvantages

Vinyl records are vulnerable to dust, heat warping, scuffs, and scratches. Dust in the groove is usually heard as noise and may be ground into the vinyl by the passing stylus, causing lasting damage. A warp can cause a regular "wow" or fluctuation of musical pitch, and if substantial it can make a record physically unplayable. A scuff will be heard as a swishing sound. A scratch will create an audible tick or pop once each revolution when the stylus encounters it. A deep scratch can throw the stylus out of the groove; if it jumps to a place farther inward, part of the recording is skipped; if it jumps outward to a part of the groove it just finished playing, it can get stuck in an infinite loop, playing the same bit over and over until someone stops it. This last type of mishap, which in the era of brittle shellac records was more commonly caused by a crack, spawned the simile "like a broken record" to refer to annoying and seemingly endless repetition.^{[citation needed]}

Records used in radio stations can suffer cue burn, which results from disc jockeys placing the needle at the beginning of a track, turning the record back and forth to find the exact start of the music, then backing up about a quarter turn, so that when it is released the music will start immediately after the fraction of a second needed for the disc to come up to full speed. When this is done repeatedly, the affected part of the groove is heavily worn and a hissing sound will be noticeable at the start of the track.^{[citation needed]}

The process of playing a vinyl record with a stylus is by its very nature to some degree a destructive process. Wear to either the stylus or the vinyl results in diminished sound quality. Record wear can be reduced significantly by the use of a high-quality, correctly adjusted turntable and tonearm, a high-compliance magnetic cartridge with a high-end stylus in good condition, and careful record handling, with non-abrasive removal of dust before playing and other cleaning if necessary. Wear from playback is eliminated by using an optical record player, as no needle comes into contact with the record.^{[citation needed]}

Groove

The average LP has about 1,500 feet (460 m; 0.28 mi) of groove on each side. The average tangential needle speed relative to the disc surface is approximately 1 mile per hour (1.6 km/h; 0.45 m/s). It travels fastest on the outside edge, unlike audio CDs, which change their speed of rotation to provide constant linear velocity (CLV). (By contrast, CDs play from the inner radius outward, the reverse of phonograph records.)^{[citation needed]}

Thin, closely spaced spiral grooves that allowed for increased playing time on a 33+1⁄3 rpm microgroove LP led to a faint pre-echo warning of upcoming loud sounds. The cutting stylus unavoidably transferred some of the subsequent groove wall's impulse signal into the previous groove wall. It was discernible by some listeners throughout certain recordings but a quiet passage followed by a loud sound would allow anyone to hear a faint pre-echo of the loud sound occurring 1.8 seconds ahead of time.^[36] This problem could also appear as post-echo, with a ghost of the sound arriving 1.8 seconds after its main impulse. Pre- and post-echo can be avoided by the use of direct metal mastering.^{[citation needed]}

The first LP records introduced used fixed pitch grooves just like their 78 predecessors. The use of magnetic tape for the production of the master recordings allowed the introduction of variable pitch grooves. The magnetic tape reproducer used to transfer the recording to the master disc was equipped with an auxiliary playback head positioned ahead of the main head by a distance equal to one revolution of the disc. The sole purpose of this head was to monitor the amplitude of the recording. If the sound level from both the auxiliary and main magnetic heads was loud, the cutting head on the disc recording lathe was driven at its normal speed. If the sound level from both magnetic heads was quieter, however, then the disc cutting head could be driven at a lower speed reducing the groove pitch with no danger of the adjacent grooves colliding with each other. The playing time of the disc was therefore increased by an amount dependent on the duration of quieter passages.^{[citation needed]}

The record manufacturers had also realised that by reducing the amplitude of the lower frequencies recorded in the groove, it was possible to decrease the spacing between the grooves and further increase the playing time. These low frequencies were then restored to their original level on playback. Furthermore, if the amplitude of the high frequencies was artificially boosted on recording the disc and then subsequently reduced to their original level on playback, the noise introduced by the disc would be reduced by a similar amount. This gave rise to an equalization frequency response applied during record coupled with an inverse of the response applied on playback. Each disc manufacturer applied its own version of an equalization curve (mostly because each manufacturer's equalization curve was protected by interlocking patents). Low-end reproduction equipment applied a compromise playback equalization that reproduced most discs reasonably well. By contrast, amplifiers for audiophile equipment were equipped with an equalization selector with a position for most, if not all, disc manufacturers. The net effect of equalization is to allow longer playing time and lower background noise while maintaining full fidelity of music or other content.^{[citation needed]}

In 1954, the Recording Industry Association of America (RIAA) introduced a standard equalization curve to be used by all record manufacturers. Consequently, both low-quality and audiophile reproducers alike could replay any recording with the correct equalization. There are two versions of the reproduction RIAA equalization curve. The first curve is the inverse of the recording curve designed for cheaper equipment using crystal or ceramic reproduction cartridges. The second curve is intended for equipment fitted with magnetic reproduction cartridges where the output voltage is dependent on the frequency of the recorded signal (the voltage output is directly proportional to the frequency of the recorded signal; that is: the voltage doubles as the recorded frequency doubles).^{[citation needed]}

Fidelity and formats

 

 

LPs pressed in multicolored vinyl (Sotano Beat: A Todo Color, a various-artists compilation) and clear yellow vinyl – (Rock On Elvis by Tulsa McLean) both from Argentina.

The audio quality of LPs has increased greatly since their 1948 inception. While early LP recordings were monophonic, stereophony had been demonstrated in 1881 and Alan Blumlein had patented Stereophonic sound in 1931. Unsuccessful attempts were made to create stereophonic records starting in the 1920s, including Emory Cook's 1952 "binaural" LPs using two precisely spaced tracks on the record (one track for each channel) that had to be played with two monaural pick-ups on a tuning-fork-shaped tonearm. The modern system ultimately released by Audio Fidelity Records in November 1957 uses two modulation angles, equal and opposite 45 degrees from vertical (and so perpendicular to each other.) It can also be thought of as using traditional horizontal modulation for the sum of left and right channels (mono), making it essentially compatible with simple mono recordings, and vertical-plane modulation for the difference of the two channels.^{[citation needed]}

The following are some significant advances in the format:

• Helium-cooled cutting heads that could withstand higher levels of high frequencies (Neumann SX68); previously, the cutting engineer had to reduce the HF content of the signal sent to the record cutting head, otherwise the delicate coils could burn out
• Elliptical stylus marketed by several manufacturers at the end of the 1960s
• Cartridges that operate at lower tracking forces (2.0 grams / 20 mN), beginning from the mid-1960s
• Half-speed and one-third-speed record cutting, which extends the usable bandwidth of the record
• Longer-lasting, antistatic record compounds (e.g.: RCA Dynaflex, Q-540)
• More advanced stylus tip shapes (Shibata, Van den Hul, MicroLine, etc.)
• Direct metal mastering
• Noise-reduction (CX encoding, dbx encoding), starting from 1973
• In the 1970s, quadraphonic sound (four-channel) records became available in both discrete and matrix formats. These did not achieve the popularity of stereo records due to the expense of consumer playback equipment, competing and incompatible quad recording standards, and a lack of quality in quad-remix releases.^[37] Quad never escaped the reputation of being a gimmick, and the various (mutually incompatible) discrete surround solutions required an ultrasonic carrier signal that was technically difficult to capture and suffered degradation with playing. With the advent of DVD-Audio and Super Audio CD, multi-channel recordings once favored and championed by artists like Leopold Stokowski and Glenn Gould^[38] have made a modest comeback. In addition, new surround recordings have been made for these formats and Blu-ray Audio.
• In the later 1970s, engineers Gerry Block and Burgess Macneal devised a preview system of mastering vinyl that allowed about 10–20% more music per disc while not sacrificing dynamic range. The preview tape head was positioned far enough before the program tape head to allow the disk computer enough time to measure the peaks in low frequency and thereby expand the feed appropriately for the greater excursions of groove modulation they produce. The Compudisk system was unveiled at the 1980 AES Convention, alongside the Zuma Disk Computer (made by John W. Bittner) and the Neumann VMS-80 lathe, which had its own advanced disk computer.^{[citation needed]}

The composition of vinyl used to press records (a blend of polyvinyl chloride and polyvinyl acetate) has varied considerably over the years. Virgin vinyl is preferred, but during the 1970s energy crisis, it became commonplace to use recycled vinyl. Sound quality suffered, with increased ticks, pops, and other surface noises.^[39] Other experiments included reducing the thickness of LPs, leading to warping and increased susceptibility to damage. Using a biscuit of 130 grams of vinyl had been the standard. Compare these to the original Columbia 12-inch LPs (ML 4001) at around 220 grams each. Besides the standard black vinyl, specialty records are also pressed on different colors of PVC/A or picture discs with a card picture sandwiched between two clear sides. Records in different novelty shapes have also been produced.^{[citation needed]}

In 2018, an Austrian startup, Rebeat Innovation GmBH, received US$4.8 million in funding to develop high definition vinyl records that purport to contain longer play times, louder volumes and higher fidelity than conventional vinyl LPs.^[40] Rebeat Innovation, headed by CEO Günter Loibl, has called the format 'HD Vinyl'.^[41] The HD process works by converting audio to a digital 3D topography map that is then inscribed onto the vinyl stamper via lasers, resulting in less loss of information. Many critics have expressed skepticism regarding the cost and quality of HD records.^[42]

In May 2019, at the Making Vinyl conference in Berlin, Loibl unveiled the Perfect Groove software for creating 3D topographic audio data files.^[43] This is a critical step in the production of HD Vinyl stampers, as they provide the map for subsequent laser-engraving. The audio engineering software was created with mastering engineers Scott Hull and Darcy Proper, a four-time Grammy winner. The demonstration offered the first simulations of what HD Vinyl records are likely to sound like, ahead of actual HD vinyl physical record production. Loibl discussed the Perfect Groove software at a presentation titled "Vinyl 4.0 The next generation of making records" before offering demonstrations to attendees.^[44]

Use by disc jockeys

Disc jockeys (or DJs) in clubs still frequently use vinyl records, as cueing tracks from cassette tapes is too slow and CDs did not allow creative playback options until the advent of the CDJ-1000 turntable in 2001. The term "DJ", which had always meant a person who played various pieces of music on the radio (originally 78s, then 45s, then tape cartridges and reels; now cuts from CDs or tracks on a computer) – a play on the horse-racing term "jockey" – has also come to encompass all kinds of skills in "scratching" (record playback manipulation) and mixing dance music, rapping over the music or even playing musical instruments, but the original dance club (non-radio) definition was simply somebody who played records, alternating between two turntables. The skill came in subtly matching beats or instruments from one song to the next, providing a consistent dance tempo. DJs also made occasional announcements and chatted on the side with patrons while songs were playing to take requests, similar to what radio disc jockeys have been doing since the 1940s.^{[citation needed]}

See also

•  Record production portal

• Album cover
• Conservation and restoration of vinyl discs

References

1. "Origin of LP". merriam-webster.com.
2. Zipkin, Michele (April 8, 2020). "Best albums from the last decade, according to critics". Stacker. Retrieved June 3, 2020.
3. "Infographic: The LP is Back!". Statista Infographics. Retrieved July 16, 2017.
4. "Full-length LP records on 150 and 180 gram vinyl". Standard Vinyl. Standard Vinyl. Retrieved December 18, 2018.
5. Jenkins, Amanda (April 13, 2019). "Inside the Archival Box: The First Long-Playing Disc". Now See Hear! The National Audio-Visual Conservation Center Blog. Library of Congress. Retrieved September 12, 2022.
6. Parmenter, Jamie; SouthFloridaReporter.com (October 23, 2019). "5 Facts You Didn't Know About Vinyl Records". Vinyl Chapters. Retrieved September 12, 2022.
7. Grayson, Eric. "Grayson on Film: Sounds and Silences", Classic Images. September 2022
8. Rider, John Francis (1941). Automatic Record Changers and Recorders. New York: J. F. Rider Inc. p. 31 – via HathiTrust.
9. "AES Section Meeting Reports » New York - September 15, 2009". www.aes.org. Retrieved September 12, 2022. Ron also showed an 16-inch Viatphone transcription disc which had been recorded at 33-1/3 rpm to yield a playing time of ten minutes. This matched the length of one 35mm film reel. He then passed around a massive oil-damped tone arm from a Vitaphone playback turntable. It required a tracking force on the order of two ounces and a steel needle which had to be replaced after each use.
10. "Frequently Asked Questions". The Vitaphone Project. Retrieved August 12, 2011.
11. Barnett, Kyle (2021). Record Cultures: The Transformation of the U.S. Recording Industry. Ann Arbor, Michigan: University of Michigan Press. pp. 168–169. ISBN 978-0-472-13103-7. OCLC 1119740862.
12. Hougen, Jim (July 1999). "OTR for the Digital Age: Recovery of Old Program Material, Part 1" (PDF). Return with Us Now... Radio Historical Association of Colorado. 24 (12): 5–6.
13. Russo, Alexander (2010). Points on the Dial: Golden Age Radio Beyond the Networks. Durham, North Carolina: Duke University Press. pp. 92–93. ISBN 978-0-8223-4517-6. OCLC 436866946.
14. "Rand's Esoteric OTR: Types of transcriptions and radio recordings". Randsesotericotr.podbean.com. Retrieved August 12, 2011.
15. "Phonograph Disks Run for Half-Hour". The New York Times. September 18, 1931. p. 48. from the original on June 22, 2022. Retrieved June 22, 2022.
16. Compton Pakenham (September 20, 1931). "Newly Recorded Music". The New York Times. p. X10. Retrieved June 22, 2022.{{cite news}}: CS1 maint: url-status (link)
17. "Not So New" (PDF). The Billboard. June 5, 1948. p. 17. (PDF) from the original on January 27, 2021. Retrieved June 22, 2022 – via World Radio History.
18. Goldmark, Peter. Maverick inventor; My Turbulent Years at CBS. New York: Saturday Review Press, 1973.
19. Ben Sisario (October 6, 2012). "Howard H. Scott, a Developer of the LP, Dies at 92". The New York Times. Retrieved October 8, 2012. Howard H. Scott, who was part of the team at Columbia Records that introduced the long-playing vinyl record in 1948 before going on to produce albums with the New York Philharmonic, Glenn Gould, Isaac Stern and many other giants of classical music, died on Sept. 22 in Reading, Pa. He was 92. ...
20. "Columbia Diskery, CBS Show Microgroove Platters to Press; Tell How It Began" (PDF). Billboard. June 26, 1948. p. 3. (PDF) from the original on January 22, 2021. Retrieved June 22, 2022..
21. The First Long-Playing Disc Library of Congress (Congress.gov) (accessdate June 21, 2021)
22. Marmorstein, Gary. The Label: The Story of Columbia Records. New York: Thunder's Mouth Press; p. 165.
23. "78 Speed On Way Out; LP-45 Trend Gaining", The Billboard, August 2, 1952, p. 47.
24. Robert Shelton (March 16, 1958). "Happy Tunes on Cash Registers". The New York Times. p. XX14.
25. Christgau, Robert (1981). "The Criteria". Christgau's Record Guide: Rock Albums of the Seventies. Ticknor & Fields. ISBN 978-0899190259. Retrieved April 6, 2019 – via robertchristgau.com.
26. Kornelis, Chris (January 27, 2015). "Why CDs May Actually Sound Better Than Vinyl". L.A. Weekly.
27. 1 What a record! The UK album chart reaches its 1,000th No1... and counting, Express, Adrian Lee, November 26, 2013
28. RIAA 2018 Year-End Music Industry Revenue Report
29. . riaa.com. Archived from the original on December 10, 1997. Retrieved December 31, 2016.
30. McGeehan, Patrick (December 7, 2009). "Vinyl Records and Turntables Are Gaining Sales". The New York Times. Retrieved May 11, 2010.
31. "Why Do Records Spin at 33 1/3 RPM?". The Sound of Vinyl Blog. June 12, 2017.
32. "10-inch LP (1948 – 1980s) – Museum Of Obsolete Media". www.obsoletemedia.org. November 23, 2013.
33. 90 Minutes with Arthur Fiedler and the Boston Pops, Radio Shack/Realistic Cat. No. 50-2040, 1976 (copyright 1974, 1976, Polydor Records)
34. London Symphony Orchestra, Previn Plays Gershwin, André Previn, pianist and conductor (featuring Rhapsody in Blue, An American in Paris and the Concerto in F for Piano and Orchestra), Angel SFO 36810, circa 1979.
35. Rider (1941), pp. 47–48.
36. . Audacity Forum. Archived from the original (Forum Discussion) on June 9, 2009.
37. "Analog Quadraphonic Formats". Retrieved April 8, 2015.
38. Gould Radio Portrait of Stokowski for CBC
39. Adrian Hope (January 24, 1980). "Pressing Problems for a Record Future". New Scientist. p. 229 ff.
40. Hogan, Marc (April 11, 2018). "'High Definition Vinyl' Is Happening, Possibly as Early as Next Year". Pitchfork. Retrieved December 17, 2018.
41. Rose, Brent (April 20, 2018). "What Is HD Vinyl and Is It Legit?". Gizmodo. Retrieved May 1, 2019.
42. Seppala, Timothy J. (April 26, 2018). "HD vinyl is a promise, not a product". Endgadget. Retrieved December 17, 2018.
43. "HD Vinyl Takes Next Step with Debut of 3D Topography Software Perfect Groove". Making Vinyl. April 4, 2019. Retrieved May 14, 2019.
44. " "Making Vinyl Europe – Program – Meistersaal, Berlin". Making Vinyl. May 2, 2019. Retrieved May 14, 2019.

External links

 

Wikimedia Commons has media related to LP records.

• "The History Of The LP Record". Classical33.co.uk