USB-C

USB-C, or USB Type-C, is a 24-pin connector (not a protocol) that supersedes previous USB connectors and can carry audio, video and other data, e.g., to drive multiple displays or to store a backup to an external drive. It can also provide and receive power, such as powering a laptop or a mobile phone. It is applied not only by USB technology, but also by other protocols, including Thunderbolt, PCIe, HDMI, DisplayPort, and others. It is extensible to support future standards.

USB-C

Pins of the USB-C connector
Type	Digital audio / video / data / power – connector
Production history
Designer	USB Implementers Forum
Designed	11 August 2014 (published)^[1]
Superseded	All earlier USB connectors (Type-A and -B, and its different sizes: Standard, Mini, and Micro) DisplayPort Mini DisplayPort Lightning
General specifications
Pins	24

USB-C plug

USB-C (SuperSpeed USB 5Gbps) receptacle on an MSI laptop

Design for the USB-C connector was initially developed in 2012 by Apple Inc. and Intel.^[2] Type-C Specification 1.0 was published by the USB Implementers Forum (USB-IF) on August 11, 2014.^[3] In July 2016, it was adopted by the IEC as "IEC 62680-1-3".^[4]

The USB Type-C connector has 24 pins and is reversible.^[5][6] The designation "C" is to distinguish it from the various former USB connectors it replaced, all termed either Type-A or Type-B. Whereas earlier every USB cable had a host end A and a peripheral device end B, USB-C replaces both; a USB-C cable connects either way, and for older equipment a legacy cable has a Type-C plug at one end and either a Type-A (host) or a Type-B (peripheral device) plug at the other. The designation "C" refers only to the connector's physical configuration, or form factor, not to be confused with the connector's specific capabilities, such as Thunderbolt 3, DisplayPort 2.0, or USB 3.2 Gen 2x2. Based on the protocols supported by both devices, host and peripheral device, a USB-C connection normally provides (much) higher signaling and therefore data rates than the superseded connectors.

A device with a Type-C connector does not necessarily implement any USB transfer protocol, USB Power Delivery, or any of the Alternate Modes: the Type-C connector is common to several technologies while mandating only a few of them.^[7]

USB 3.2, released in September 2017, fully replaced the USB 3.1 specification. It preserves previously called USB 3.1 SuperSpeed and SuperSpeed+ data transfer modes and introduces two additional data transfer modes by newly applying two-lane operations, with signaling rates of 10 Gbit/s (SuperSpeed USB 10Gbps; nominal data rate: 1.212 GB/s) and 20 Gbit/s (SuperSpeed USB 20Gbps; nominal data rate: 2.422 GB/s). They are only applicable with Full-Featured USB-C Fabrics (connectors and cables) on both ends.

USB4, released in 2019, is the first USB transfer protocol standard that is only available exclusively via USB-C Fabrics.

Ease of use

The USB-C standard simplifies usage by specifying cables having identical plugs on both ends, which can be inserted without concern about orientation. When connecting two devices, the user can plug either end of the cable into either device. The plugs are flat, but will work if inserted right-side-up or upside-down.

The USB-C plugs have two-fold rotational symmetry because a plug may be inserted into a receptacle in either of two orientations. Electrically, USB-C plugs are not symmetric, as can be seen in the tables of pin layouts. Also the two ends of the USB-C are electrically different, as can be seen in the table of cable wiring. The illusion of symmetry results from how devices respond to the cable. Software makes the plugs and cables behave as though they are symmetric. According to the specifications, "Determination of this host-to-device relationship is accomplished through a Configuration Channel (CC) that is connected through the cable."^[8]

The USB-C standard attempts to eliminate the need to have different cables for other communication technologies, such as Thunderbolt, PCIe, HDMI, DisplayPort, and more. USB-C cables can contain circuit boards and processors giving them much more capability than simple circuit connections.

Overview

USB-C cables interconnect hosts and peripheral devices, replacing various other electrical cables and connectors, including all earlier (legacy) USB connectors, HDMI connectors, DisplayPort ports, and 3.5 mm audio jacks.^[9][10]

Name

USB Type-C and USB-C are trademarks of the USB Implementers Forum.^[11]

Connectors

 

USB-C port on MacBook Pro (middle port)

The 24-pin double-sided connector is slightly larger than the micro-B connector, with a USB-C receptacle measuring 8.4 millimetres (0.33 in) wide, 2.6 millimetres (0.10 in) high, and 6.65 millimetres (0.262 in) deep.

Cables

USB 3.1 cables are considered full-featured USB-C cables. They are electronically marked cables that contain a chip with an ID function based on the configuration channel and vendor-defined messages (VDM) from the USB Power Delivery 2.0 specification. Cable length should not exceed 2 metres (6 ft 7 in) for Gen 1, and 1 metre (3 ft 3 in) for Gen 2.^[12] The electronic ID chip provides information about product/vendor, cable connectors, USB signaling protocol (2.0, Gen 1, Gen 2), passive/active construction, use of V_CONN power, available V_BUS current, latency, RX/TX directionality, SOP controller mode, and hardware/firmware version.^[7]

USB-C cables that do not have shielded SuperSpeed pairs, sideband use pins, or additional wires for power lines can have increased cable length, up to 4 metres (13 ft). These USB-C cables only support USB 2.0 (up to 480 Mbit/s) and do not support Alternate Modes. Active cables (those with built-in repeaters) can support SuperSpeed USB 5Gbps (= USB 3.2 Gen 1x1 = USB 3.1 Gen 1 = USB 3.0) only over lengths up to 10 metres (33 ft).

All USB-C cables must be able to carry a minimum of 3 A current (at 5 V, for 15 W) but some can carry 5 A current (at 20 V, for 100 W).^[13] USB-C to USB-C cables supporting 5 A current must contain e-marker chips (also marketed as E-Mark chips) programmed to identify the cable and its current capabilities. USB charging ports should be clearly marked with power capability.^[14]

Full-featured USB-C cables that implement USB 3.1 Gen 2 can provide 10 Gbit/s (full duplex) signalling rate. They are marked with a SuperSpeed USB 10Gbps (previously marketed as SuperSpeed+) logo. There are also cables which can support only USB 2.0 with a nominal data rate of 480 Mbit/s (with maximal effective data rate of ~40MB/s). The USB Implementers Forum certifies valid cables so they can be marked accordingly and users can distinguish them from non-compliant products.^[15]

Hosts and peripheral devices

For any two pieces of equipment connecting over USB, one is a host (with a downstream-facing port, DFP) and the other is a peripheral device (with an upstream-facing port, UFP). Some products, such as mobile phones, can take either role, whichever is opposite that of the connected equipment. Such equipment is said to have Dual-Role-Data (DRD) capability, which was known as USB On-The-Go in the previous specification.^[16] With USB-C, when two such devices are connected, the roles are first randomly assigned, but a swap can be commanded from either end, although there are optional path and role detection methods that would allow equipment to select a preference for a specific role. Furthermore, Dual-Role equipment that implements USB Power Delivery may swap data and power roles independently using the Data Role Swap or Power Role Swap processes. This allows for charge-through hub or docking station applications such as a portable computer acting as a host to connect to peripherals but being powered by the dock, or a computer being powered by a display, through a single USB-C cable.^[7]

USB-C devices may optionally provide or consume bus power currents of 1.5 A and 3.0 A (at 5 V) in addition to baseline bus power provision; power sources can either advertise increased USB current through the configuration channel or implement the full USB Power Delivery specification using both the BMC-coded configuration line and the legacy BFSK-coded V_BUS line.^[7][14]

All older USB connectors (all Type-A and Type-B) are designated legacy. Connecting legacy and modern, USB-C equipment requires either a legacy cable assembly (a cable with any Type-A or Type-B plug on one end and a Type-C plug on the other) or, in very specific cases, a legacy adapter assembly.

An older device can connect to a modern (USB-C) host by using a legacy cable, with a Standard-B, Mini-B, or Micro-B plug on the device end and a USB-C plug on the other. Similarly, a modern device can connect to a legacy host by using a legacy cable with a USB-C plug on the device end and a Standard-A plug on the host end. Legacy adapters with USB-C receptacles are "not defined or allowed" by the specification because they can create "many invalid and potentially unsafe" cable combinations (being any cable assembly with two A ends or two B ends). However, exactly two types of adapter with USB-C plugs are defined: one with a Standard-A receptacle (for connecting a legacy device (such as a flash drive—not a cable) to a modern host, and supporting up to USB 3.1), and one with a Micro-B receptacle (for connecting a modern device to a legacy host, and supporting up to USB 2.0).^[17]

Non-USB modes

Audio adapter accessory mode

A device with a USB-C port may support analog headsets through an audio adapter with a 3.5 mm jack, providing three analog audio channels (left and right output and microphone). The audio adapter may optionally include a USB-C charge-through port to allow 500 mA device charging. The engineering specification states that an analog headset shall not use a USB-C plug instead of a 3.5 mm plug. In other words, headsets with a USB-C plug should always support digital audio (and optionally the accessory mode).^[18]

Analog signals use the USB 2.0 differential pairs (Dp and Dn for Right and Left) and the two side-band use pairs for Mic and GND. The presence of the audio accessory is signaled through the configuration channel and V_CONN.

Alternate modes

See also: USB-C § Alternate Mode partner specifications

An Alternate Mode dedicates some of the physical wires in a USB-C cable for direct device-to-host transmission using non-USB data protocols, such as DisplayPort or Thunderbolt. The four high-speed lanes, two side-band pins, and (for dock, detachable device and permanent-cable applications only) five additional pins can be used for Alternate Mode transmission. The modes are configured using vendor-defined messages (VDM) through the configuration channel.

Specifications

USB Type-C cable and connector specifications

The USB Type-C specification 1.0 was published by the USB Implementers Forum (USB-IF) and was finalized in August 2014.^[10]

It defines requirements for cables and connectors.

• Rev 1.1 was published 2015-04-03^[19]
• Rev 1.2 was published 2016-03-25^[20]
• Rev 1.3 was published 2017-07-14^[21]
• Rev 1.4 was published 2019-03-29^[21]
• Rev 2.0 was published 2019-08-29^[22]
• Rev 2.1 was published 2021-05-25 (USB PD - Extended Power Range - 48 V - 5 A - 240 W)^[23]
• Rev 2.2 was published 2022-10-18, primarily for enabling USB4 Version 2.0 (80 Gbps) over USB Type-C connectors and cables.^[17]
• Rev 2.3 was published 2023-10-31.

Adoption as IEC specification:

• IEC 62680-1-3:2016 (2016-08-17, edition 1.0) "Universal serial bus interfaces for data and power – Part 1-3: Universal Serial Bus interfaces – Common components – USB Type-C cable and connector specification"^[24]
• IEC 62680-1-3:2017 (2017-09-25, edition 2.0) "Universal serial bus interfaces for data and power – Part 1-3: Common components – USB Type-C Cable and Connector Specification"^[25]
• IEC 62680-1-3:2018 (2018-05-24, edition 3.0) "Universal serial bus interfaces for data and power – Part 1-3: Common components – USB Type-C Cable and Connector Specification"^[26]

Receptacles

 

Type-C receptacle pinout (end-on view)

The receptacle features four power and four ground pins, two differential pairs (connected together on devices) for legacy USB 2.0 high-speed data, four shielded differential pairs for Enhanced SuperSpeed data (two transmit and two receive pairs), two Sideband Use (SBU) pins, and two Configuration Channel (CC) pins.

Type-C receptacle A pin layout

Pin	Name	Description
A1	GND	Ground return
A2	SSTXp1 ("TX1+")	SuperSpeed differential pair #1, transmit, positive
A3	SSTXn1 ("TX1-")	SuperSpeed differential pair #1, transmit, negative
A4	VBUS	Bus power
A5	CC1	Configuration channel
A6	D+	USB 2.0 differential pair, position 1, positive
A7	D-	USB 2.0 differential pair, position 1, negative
A8	SBU1	Sideband use (SBU)
A9	VBUS	Bus power
A10	SSRXn2 ("RX2-")	SuperSpeed differential pair #4, receive, negative
A11	SSRXp2 ("RX2+")	SuperSpeed differential pair #4, receive, positive
A12	GND	Ground return

Type-C receptacle B pin layout

Pin	Name	Description
B12	GND	Ground return
B11	SSRXp1 ("RX1+")	SuperSpeed differential pair #2, receive, positive
B10	SSRXn1 ("RX1-")	SuperSpeed differential pair #2, receive, negative
B9	VBUS	Bus power
B8	SBU2	Sideband use (SBU)
B7	D-	USB 2.0 differential pair, position 2, negative^[a]
B6	D+	USB 2.0 differential pair, position 2, positive^[a]
B5	CC2	Configuration channel
B4	VBUS	Bus power
B3	SSTXn2 ("TX2-")	SuperSpeed differential pair #3, transmit, negative
B2	SSTXp2 ("TX2+")	SuperSpeed differential pair #3, transmit, positive
B1	GND	Ground return

1. There is only a single non-SuperSpeed differential pair in the cable. This pin is not connected in the plug/cable.

Plugs

 

Type-C plug pinout (end-on view)

The plug has only one USB 2.0 high-speed differential pair, and one of the CC pins (CC2) is replaced by V_CONN, to power optional electronics in the cable, and the other is used to actually carry the Configuration Channel (CC) signals. These signals are used to determine the orientation of the cable, as well as to carry USB Power Delivery communications.

Cables

Although plugs have 24 pins, cables have only 18 wires. In the following table, the "No." column shows the wire number.

Full-Featured USB 3.2 and 2.0 Type-C cable wiring

Plug 1, USB Type-C		USB Type-C cable					Plug 2, USB Type-C
Pin	Name	Wire color	No.	Name	Description	2.0^[a]	Pin	Name
Shell	Shield	Braid	Braid	Shield	Cable external braid		Shell	Shield
A1, B12, B1, A12	GND	Tin-plated	1	GND_PWRrt1	Ground for power return		A1, B12, B1, A12	GND
			16	GND_PWRrt2
A4, B9, B4, A9	VBUS	Red	2	PWR_VBUS1	VBUS power		A4, B9, B4, A9	VBUS
			17	PWR_VBUS2
B5	VCONN	Yellow	18	PWR_VCONN	VCONN power, for powered cables^[b]		B5	VCONN
A5	CC	Blue	3	CC	Configuration channel		A5	CC
A6	D+	Green	4	UTP_Dp^[c]	Unshielded twisted pair, positive		A6	D+
A7	D-	White	5	UTP_Dn^[c]	Unshielded twisted pair, negative		A7	D-
A8	SBU1	Red	14	SBU_A	Sideband use A		B8	SBU2
B8	SBU2	Black	15	SBU_B	Sideband use B		A8	SBU1
A2	SSTXp1	Yellow^[d]	6	SDPp1	Shielded differential pair #1, positive		B11	SSRXp1
A3	SSTXn1	Brown^[d]	7	SDPn1	Shielded differential pair #1, negative		B10	SSRXn1
B11	SSRXp1	Green^[d]	8	SDPp2	Shielded differential pair #2, positive		A2	SSTXp1
B10	SSRXn1	Orange^[d]	9	SDPn2	Shielded differential pair #2, negative		A3	SSTXn1
B2	SSTXp2	White^[d]	10	SDPp3	Shielded differential pair #3, positive		A11	SSRXp2
B3	SSTXn2	Black^[d]	11	SDPn3	Shielded differential pair #3, negative		A10	SSRXn2
A11	SSRXp2	Red^[d]	12	SDPp4	Shielded differential pair #4, positive		B2	SSTXp2
A10	SSRXn2	Blue^[d]	13	SDPn4	Shielded differential pair #4, negative		B3	SSTXn2

1. USB 2.0 Type-C cables do not include wires for SuperSpeed or sideband use.
2. V_CONN must not traverse end-to-end through the cable. Some isolation method must be used.
3. There is only a single differential pair for non-SuperSpeed data in the cable, which is connected to A6 and A7. Contacts B6 and B7 should not be present in the plug.
4. Wire colors for differential pairs are not mandated.

Related USB-IF specifications

USB Type-C Locking Connector Specification

The USB Type-C Locking Connector Specification was published 2016-03-09. It defines the mechanical requirements for USB-C plug connectors and the guidelines for the USB-C receptacle mounting configuration to provide a standardized screw lock mechanism for USB-C connectors and cables.^[27]

USB Type-C Port Controller Interface Specification

The USB Type-C Port Controller Interface Specification was published 2017-10-01. It defines a common interface from a USB-C Port Manager to a simple USB-C Port Controller.^[28]

USB Type-C Authentication Specification

Adopted as IEC specification: IEC 62680-1-4:2018 (2018-04-10) "Universal Serial Bus interfaces for data and power - Part 1-4: Common components - USB Type-C Authentication Specification"^[29]

USB 2.0 Billboard Device Class Specification

USB 2.0 Billboard Device Class is defined to communicate the details of supported Alternate Modes to the computer host OS. It provides user readable strings with product description and user support information. Billboard messages can be used to identify incompatible connections made by users. They optionally appear to negotiate multiple Alternate Modes and must appear when negotiation fails between the host (source) and device (sink).

USB Audio Device Class 3.0 Specification

USB Audio Device Class 3.0 defines powered digital audio headsets with a USB-C plug.^[7] The standard supports the transfer of both digital and analog audio signals over the USB port.^[30]

USB Power Delivery Specification

Main article: USB Power Delivery

While it is not necessary for USB-C compliant devices to implement USB Power Delivery, for USB-C DRP/DRD (Dual-Role-Power/Data) ports, USB Power Delivery introduces commands for altering a port's power or data role after the roles have been established when a connection is made.^[31]

USB 3.2 Specification

USB 3.2, released in September 2017, replaces the USB 3.1 standard. It preserves existing USB 3.1 SuperSpeed and SuperSpeed+ data modes and introduces two new SuperSpeed+ transfer modes over the USB-C connector using two-lane operation, doubling the data rates to 10 and 20 Gbit/s (1 and ~2.4 GB/s). USB 3.2 is only supported by USB-C, making micro-USB connectors obsolete.

USB4 Specification

The USB4 specification released in 2019 is the first USB data transfer specification to exclusively use the Type-C connector.

Alternate Mode partner specifications

As of 2018,^[update] five system-defined Alternate Mode partner specifications exist. Additionally, vendors may support proprietary modes for use in dock solutions. Alternate Modes are optional; Type-C features and devices are not required to support any specific Alternate Mode. The USB Implementers Forum is working with its Alternate Mode partners to make sure that ports are properly labelled with respective logos.^[32]

List of Alternate Mode partner specifications

Logo	Name	Date	Protocol	Status
	Thunderbolt Alternate Mode	Announced in June 2015^[33]	USB-C is the native (and only) connector for Thunderbolt 3 and later Thunderbolt 3 (also carries 4× PCI Express 3.0, DisplayPort 1.2, DisplayPort 1.4, USB 3.1 Gen 2),^[33]^[34]^[35]^[36] Thunderbolt 4 (also carries 4× PCI Express 3.0, DisplayPort 2.0, USB4), Thunderbolt 5 (also carries 4× PCI Express 4.0, DisplayPort 2.1, USB4)	Current
	DisplayPort Alternate Mode	Published in September 2014	DisplayPort 1.2, DisplayPort 1.4,^[37]^[38] DisplayPort 2.0^[39]	Current
	Mobile High-Definition Link (MHL) Alternate Mode	Announced in November 2014^[40]	MHL 1.0, 2.0, 3.0 and superMHL 1.0^[41]^[42]^[43]^[44]	Current
	HDMI Alternate Mode	Announced in September 2016^[45]	HDMI 1.4b^[46]^[47]^[48]^[49]	Not being updated
	VirtualLink Alternate Mode	Announced in July 2018^[50]	VirtualLink 1.0^[51]	Abandoned

Other protocols like Ethernet^[52] have been proposed, although Thunderbolt 3 and later are also capable of 10 Gigabit Ethernet networking.^[53]

All Thunderbolt 3 controllers support both Thunderbolt Alternate Mode and DisplayPort Alternate Mode.^[54] Because Thunderbolt can encapsulate DisplayPort data, every Thunderbolt controller can either output DisplayPort signals directly over DisplayPort Alternative Mode or encapsulated within Thunderbolt in Thunderbolt Alternate Mode. Low-cost peripherals mostly connect via DisplayPort Alternate Mode while some docking stations tunnel DisplayPort over Thunderbolt.^[55]

DisplayPort Alternate Mode 2.0: DisplayPort 2.0 can run directly over USB-C alongside USB4. DisplayPort 2.0 can support 8K resolution at 60 Hz with HDR10 color and can use up to 80 Gbps, which is double the amount available to USB data.^[56]

The USB SuperSpeed protocol is similar to DisplayPort and PCIe/Thunderbolt, in using packetized data transmitted over differential LVDS lanes with embedded clock using comparable bit rates, so these Alternate Modes are easier to implement in the chipset.^[37]

Alternate Mode hosts and sinks can be connected with either regular Full-Featured Type-C cables, or with converter cables or adapters:

USB 3.1 Type-C to Type-C Full-Featured cable

DisplayPort, Mobile High-Definition Link (MHL), HDMI and Thunderbolt (20 Gbit/s, or 40 Gbit/s with cable length up to 0.5 m^{[citation needed]}) Alternate Mode Type-C ports can be interconnected with standard passive Full-Featured USB Type-C cables. These cables are only marked with standard "trident" SuperSpeed USB logo (for Gen 1 cables) or the SuperSpeed+ USB 10 Gbit/s logo (for Gen 2 cables) on both ends.^[57] Cable length should be 2.0 m or less for Gen 1 and 1.0 m or less for Gen 2.

Thunderbolt Type-C to Type-C active cable

Thunderbolt 3 (40 Gbit/s) Alternate Mode with cables longer than 0.8 m requires active Type-C cables that are certified and electronically marked for high-speed Thunderbolt 3 transmission, similarly to high-power 5 A cables.^[33][36] These cables are marked with a Thunderbolt logo on both ends. They do not support USB 3 backwards compatibility, only USB 2 or Thunderbolt. Cables can be marked for both Thunderbolt and 5 A power delivery at the same time.^[58]

Active cables and adapters contain powered electronics to allow for longer cables or to perform protocol conversion. The adapters for video Alternate Modes may allow conversion from native video stream to other video interface standards (e.g., DisplayPort, HDMI, VGA or DVI).

Using Full-Featured Type-C cables for Alternate Mode connections provides some benefits. Alternate Mode does not employ USB 2.0 lanes and the configuration channel lane, so USB 2.0 and USB Power Delivery protocols are always available. In addition, DisplayPort and MHL Alternate Modes can transmit on one, two, or four SuperSpeed lanes, so two of the remaining lanes may be used to simultaneously transmit USB 3.1 data.^[59]

Alternate Mode protocol support matrix for Type-C cables and adapters

Mode	USB 3.1 Type-C cable^[a]							Adapter cable or adapter					Construction
	USB^[b]	DisplayPort		Thunderbolt		superMHL	HDMI	HDMI		DVI-D		Component video
	3.1	1.2	1.4	20 Gbit/s	40 Gbit/s		1.4b	1.4b	2.0b	Single-link	Dual-link	(YPbPr, VGA/DVI-A)
DisplayPort	Yes	Yes		Does not appear				No					Passive
	Does not appear	Optional						Yes		Yes		Yes	Active
Thunderbolt	Yes^[c]	Yes^[c]		Yes	Yes^[d]	Does not appear		No					Passive
	Does not appear	Optional		Optional	Yes			Yes		Yes		Yes	Active
MHL	Yes	Does not appear				Yes	Does not appear	Yes	No	Yes	No	No	Passive
	Does not appear					Optional		Does not appear	Yes	Does not appear		Yes	Active
HDMI	Does not appear						Yes	Yes	No	Yes	No	No	Passive
							Optional	Does not appear				Yes	Active

1. USB 2.0 and USB Power Delivery are available at all times in a Type-C cable
2. USB 3.1 can be transmitted simultaneously when the video signal bandwidth requires two or fewer lanes.
3. Is only available in Thunderbolt 3 DisplayPort mode
4. Thunderbolt 3 40 Gbit/s passive cables are only possible <0.8 m due to limitations of current cable technology.

USB-C receptacle pin usage in different modes

The diagrams below depict the pins of a USB-C receptacle in different use cases.

USB 2.0/1.1

A simple USB 2.0/1.1 device mates using one pair of D+/D− pins. Hence, the source (host) does not require any connection management circuitry, but it lacks the same physical connector so therefore USB-C is not backward compatible. V_BUS and GND provide 5 V up to 500 mA of current.

However, to connect a USB 2.0/1.1 device to a USB-C host, use of Rd^[60] on the CC pins is required, as the source (host) will not supply V_BUS until a connection is detected through the CC pins.

This means many USB-A–to–USB-C cables will only work in the A to C direction (connecting to a USB-C devices, e.g. for charging) as they do not include the termination resistors needed to work in the C to A direction (from a USB-C host). Adapters or cables from USB-C to a USB-A receptacle usually do work as they include the required termination resistor.

GND	TX1+	TX1−	VBUS	CC1	D+	D−	SBU1	VBUS	RX2−	RX2+	GND
GND	RX1+	RX1−	VBUS	SBU2	D−	D+	CC2	VBUS	TX2−	TX2+	GND

USB Power Delivery

The USB Power Delivery specification uses one of CC1 or CC2 pins for power negotiation between source device and sink device, up to 20 V at 5 A. It is transparent to any data transmission mode, and can therefore be used together with any of them as long as the CC pins are intact.

An extension to the specification has added 28V, 36V and 48V to support up to 240W of power for laptops, monitors, hard disks and other peripherals.^[61]

GND	TX1+	TX1−	VBUS	CC1	D+	D−	SBU1	VBUS	RX2−	RX2+	GND
GND	RX1+	RX1−	VBUS	SBU2	D−	D+	CC2	VBUS	TX2−	TX2+	GND

USB 3.0/3.1/3.2

In the USB 3.0/3.1/3.2 mode, two or four high speed links are used in TX/RX pairs to provide 5, 10, or 20 Gbit/s (only by USB 3.2 x2 two-lane operations) signalling rates respectively. One of the CC pins is used to negotiate the mode.

V_BUS and GND provide 5 V up to 900 mA, in accordance with the USB 3.1 specification. A specific USB-C mode may also be entered, where 5 V at nominal either 1.5 A or 3 A is provided.^[62] A third alternative is to establish a USB Power Delivery (USB-PD) contract.

In single-lane mode, only the differential pairs closest to the CC pin are used for data transmission. For dual-lane data transfers, all four differential pairs are in use.

The D+/D− link for USB 2.0/1.1 is typically not used when USB 3.x connection is active, but devices like hubs open simultaneous 2.0 and 3.x uplinks in order to allow operation of both types of devices connected to it. Other devices may have the ability to fall back to 2.0, in case the 3.x connection fails.

GND	TX1+	TX1−	VBUS	CC1	D+	D−	SBU1	VBUS	RX2−	RX2+	GND
GND	RX1+	RX1−	VBUS	SBU2	D−	D+	CC2	VBUS	TX2−	TX2+	GND

Alternate Modes

In Alternate Modes one of up to four high speed links are used in whatever direction is needed. SBU1, SBU2 provide an additional lower speed link. If two high speed links remain unused, then a USB 3.0/3.1 link can be established concurrently to the Alternate Mode.^[38] One of the CC pins is used to perform all the negotiation. An additional low band bidirectional channel (other than SBU) may share that CC pin as well.^[38][46] USB 2.0 is also available through D+/D− pins.

In regard to power, the devices are supposed to negotiate a Power Delivery contract before an Alternate Mode is entered.^[63]

GND	TX1+	TX1−	VBUS	CC1	D+	D−	SBU1	VBUS	RX2−	RX2+	GND
GND	RX1+	RX1−	VBUS	SBU2	D−	D+	CC2	VBUS	TX2−	TX2+	GND

Debug Accessory Mode

The external device test system (DTS) signals to the target system (TS) to enter debug accessory mode via CC1 and CC2 both being pulled down with an Rd resistor value or pulled up as Rp resistor value from the test plug (Rp and Rd defined in Type-C specification).

After entering debug accessory mode, optional orientation detection via the CC1 and CC2 is done via setting CC1 as a pullup of Rd resistance and CC2 pulled to ground via Ra resistance (from the test system Type-C plug). While optional, orientation detection is required if USB Power Delivery communication is to remain functional.

In this mode, all digital circuits are disconnected from the connector, and the 14 bold pins can be used to expose debug related signals (e.g. JTAG interface). USB IF requires for certification that security and privacy consideration and precaution has been taken and that the user has actually requested that debug test mode be performed.

GND	TX1+	TX1−	VBUS	CC1	D+	D−	SBU1	VBUS	RX2−	RX2+	GND
GND	RX1+	RX1−	VBUS	SBU2	D−	D+	CC2	VBUS	TX2−	TX2+	GND

If a reversible Type-C cable is required but Power Delivery support is not, the test plug will need to be arranged as below, with CC1 and CC2 both being pulled down with an Rd resistor value or pulled up as Rp resistor value from the test plug:

GND	TS1	TS2	VBUS	CC1	TS6	TS7	TS5	VBUS	TS4	TS3	GND
GND	TS3	TS4	VBUS	TS5	TS7	TS6	CC2	VBUS	TS2	TS1	GND

This mirroring of test signals will only provide 7 test signals for debug usage instead of 14, but with the benefit of minimizing extra parts count for orientation detection.

Audio Adapter Accessory Mode

In this mode, all digital circuits are disconnected from the connector, and certain pins become reassigned for analog outputs or inputs. The mode, if supported, is entered when both CC pins are shorted to GND. D− and D+ become audio output left L and right R, respectively. The SBU pins become a microphone pin MIC, and the analog ground AGND, the latter being a return path for both outputs and the microphone. Nevertheless, the MIC and AGND pins must have automatic swap capability, for two reasons: firstly, the USB-C plug may be inserted either side; secondly, there is no agreement, which TRRS rings shall be GND and MIC, so devices equipped with a headphone jack with microphone input must be able to perform this swap anyway.^[64]

This mode also allows concurrent charging of a device exposing the analog audio interface (through V_BUS and GND), however only at 5 V and 500 mA, as CC pins are unavailable for any negotiation.

GND	TX1+	TX1−	VBUS	CC1	R	L	MIC	VBUS	RX2−	RX2+	GND
GND	RX1+	RX1−	VBUS	AGND	L	R	CC2	VBUS	TX2−	TX2+	GND

Plug insertions detection is performed by the TRRS plug's physical plug detection switch. On plug insertions, this will pull down both CC and VCONN in the plug (CC1 and CC2 in the receptacle). This resistance must be less than 800 ohms which is the minimum "Ra" resistance specified in the USB Type-C specification). This is essentially a direct connection to USB digital ground.

TRRS rings wiring to Type-C plug (Figure A-2 of USB Type-C Cable and Connector Specification Release 1.3)

TRRS socket	Analog audio signal	USB Type-C plug
Tip	L	D−
Ring 1	R	D+
Ring 2	Microphone/ground	SBU1 or SBU2
Sleeve	Microphone/ground	SBU2 or SBU1
DETECT1	Plug presence detection switch	CC, VCONN
DETECT2	Plug presence detection switch	GND

Software support

• Android from version 6.0 "Marshmallow" onwards works with USB 3.1 and USB-C.^[65]
• ChromeOS, starting with the Chromebook Pixel 2015, supports USB 3.1, USB-C, Alternate Modes, Power Delivery, and USB Dual-Role support.^[66]
• FreeBSD released the Extensible Host Controller Interface, supporting USB 3.0, with release 8.2^[67]
• iOS from version 12.1 (iPad Pro 3rd generation or later, iPad Air 4th generation or later, iPad Mini 6th generation, iPad 10th generation, iPhone 15) onwards works with USB-C.
• NetBSD began supporting USB 3.0 with release 7.2^[68]
• Linux has supported USB 3.0 since kernel version 2.6.31 and USB version 3.1 since kernel version 4.6.
• OpenBSD began supporting USB 3.0 in version 5.7^[69]
• OS X Yosemite (macOS version 10.10.2), starting with the MacBook Retina early 2015, supports USB 3.1, USB-C, Alternate Modes, and Power Delivery.^[70]
• Windows 8.1 added USB-C and billboard support in an update.^[71]
• Windows 10 and Windows 10 Mobile support USB 3.1, USB-C, alternate modes, billboard device class, Power Delivery and USB Dual-Role.^[72][73]

Authentication

USB Type-C Authentication is an extension to the USB-C protocol which can add security to the protocol.^[74][75][76]

Hardware support

 

A Samsung Galaxy S8 plugged into a DeX docking station: The monitor is displaying the PowerPoint and Word Android applications.

USB-C devices

An increasing number of motherboards, notebooks, tablet computers, smartphones, hard disk drives, USB hubs and other devices released from 2014 onwards include the USB-C receptacles. However, the initial adoption of USB-C was limited by the high cost of USB-C cables^[77] and the wide use of Micro-USB chargers.^{[citation needed]}

Video output

Currently, DisplayPort is the most widely implemented alternate mode, and is used to provide video output on devices that do not have standard-size DisplayPort or HDMI ports, such as smartphones and laptops. All Chromebooks with a USB-C port are required to support DisplayPort alternate mode in Google's hardware requirements for manufacturers.^[78] A USB-C multiport adapter converts the device's native video stream to DisplayPort/HDMI/VGA, allowing it to be displayed on an external display, such as a television set or computer monitor.

It is also used on USB-C docks designed to connect a device to a power source, external display, USB hub, and optional extra (such as a network port) with a single cable. These functions are sometimes implemented directly into the display instead of a separate dock,^[79] meaning a user connects their device to the display via USB-C with no other connections required.

Compatibility issues

Power issues with cables

Many cables claiming to support USB-C are actually not compliant to the standard. Using these cables would have a potential consequence of damaging devices that they are connected to.^[80][81][82] There are reported cases of laptops being destroyed due to the use of non-compliant cables.^[83]

Some non-compliant cables with a USB-C connector on one end and a legacy USB-A plug or Micro-B receptacle (receptacles also being invalid on cables) on the other end incorrectly terminate the Configuration Channel (CC) with a 10 kΩ pull-up to V_BUS instead of the specification mandated 56 kΩ pull-up,^[84] causing a device connected to the cable to incorrectly determine the amount of power it is permitted to draw from the cable. Cables with this issue may not work properly with certain products, including Apple and Google products, and may even damage power sources such as chargers, hubs, or PC USB ports.^[85][86]

When a defective USB-C cable or power source is used, the voltage seen by a USB-C device can be different from the voltage expected by the device. This may result in an overvoltage on the VBUS pin. Also due to the fine pitch of the USB-C receptacle, the VBUS pin from the cable may contact with the CC pin of the USB-C receptacle resulting in a short-to-VBUS electrical issue due to the fact that the VBUS pin is rated up to 20 V while the CC pins are rated up to 5.5 V. To overcome these issues, USB Type-C port protection must be used between a USB-C connector and a USB-C Power Delivery controller.^[87]

Compatibility with audio adapters

The USB-C port can be used to connect wired accessories such as headphones.

There are two modes of audio output from devices: digital and analog. There are primarily two types of USB-C audio adapters: active, e.g. those with digital-to-analog converters (DACs), and passive, without electronics.^[88][89]

When an active set of USB-C headphones or adapter is used, digital audio is sent through the USB-C port. The conversion by the DAC and amplifier is done inside of the headphones or adapter, instead of on the phone. The sound quality is dependent on the headphones/adapter's DAC. Active adapters with a built-in DAC have near-universal support for devices that output digital and analog audio, adhering to the Audio Device Class 3.0 and Audio Adapter Accessory Mode specifications.

Examples of such active adapters include external USB sound cards and DACs that do not require special drivers,^[90] and USB-C to 3.5 mm headphone jack adapters by Apple, Google, Essential, Razer, HTC, and Samsung.^[91]

On the other hand, when a passive adapter is used, digital-to-analog conversion is done on the host device and analog audio is sent through the USB-C port. The sound quality is dependent on the phone's onboard DAC. Passive adapters are only compatible with devices that output analog audio, adhering to the Audio Adapter Accessory Mode specification.

USB-C to 3.5 mm audio adapters and USB sound cards compatibility

Output mode	Specification	Devices	USB-C adapters
			Active	Passive, without DACs
Digital audio	Audio Device Class 3.0 (digital audio)	Apple iPhone 15, Google Pixel 2, HTC U11, Essential Phone, Razer Phone, Samsung Galaxy Note 10, Samsung Galaxy S10 Lite, Sharp Aquos S2, Asus ZenFone 3, Bluedio T4S, Lenovo Tab 4, GoPro, MacBook etc.	No conversion	Conversion unavailable
Analog audio	Audio Device Class 3.0 (digital audio) Audio Adapter Accessory Mode (analog audio)	Apple iPhone 15, Moto Z/Z Force, Moto Z2/Z2 Force/Z2 Play, Moto Z3/Z3 Play, Sony Xperia XZ2, Huawei Mate 10 Pro, Huawei P20/P20 Pro, Honor Magic2, LeEco, Xiaomi phones, OnePlus 6T, OnePlus 7/7 Pro/7T/7T Pro, Oppo Find X/Oppo R17/R17 Pro, ZTE Nubia Z17/Z18 etc.	Conversion by adapter	Pass-through

Compatibility with other fast-charging technology

In 2016, Benson Leung, an engineer at Google, pointed out that Quick Charge 2.0 and 3.0 technologies developed by Qualcomm are not compatible with the USB-C standard.^[92] Qualcomm responded that it is possible to make fast-charge solutions fit the voltage demands of USB-C and that there are no reports of problems; however, it did not address the standard compliance issue at that time.^[93] Later in the year, Qualcomm released Quick Charge 4, which it claimed was – as an advancement over previous generations – "USB Type-C and USB PD compliant".^[94]

Regulations for compatibility

Further information: Radio Equipment Directive (2022)

In 2021, the European Commission proposed the use of USB-C as a universal charger.^[95][96][97] On 4 October 2022, the European Parliament voted in favor of the new law, Radio Equipment Directive 2022/2380, with 602 votes in favor, 13 against and 8 abstentions.^[98] The regulation requires that all new mobile phones, tablets, cameras, headphones, headsets, handheld video game consoles, portable speakers, e-readers, keyboards, mice, portable navigation systems, and earbuds sold in the European Union and supporting wired charging, would have to be equipped with a USB-C port and charge with a standard USB-C to USB-C cable by the end of 2024. Additionally, if these devices support fast charging, they must support USB Power Delivery. These regulations will extend to laptops by early 2026.^[99] To comply with these regulations, Apple Inc. replaced its proprietary Lightning connector with USB-C beginning with the iPhone 15 and AirPods Pro second generation, released in 2023.^[100]

See also

• USB hardware § Host and device interface receptacles
• Thunderbolt (interface)
• HDMI Version 2.1

References

1. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.3 (14 July 2017), Revision History, page 14.
2. Weintaub, Seth (2015). "Did Apple invent USB Type-C? Maybe a little bit".{{cite news}}: CS1 maint: url-status (link)
3. "Universal Serial Bus Type-C Cable and Connector Specification" (PDF). USB 3.0 Promoter Group. 2014.
4. "IEC Formally Adopts USB Type-C, USB Power Delivery and USB 3.1 Specifications" (Press release). 2016-07-13. from the original on 2021-01-30. Retrieved 2022-09-10.
5. "USB Type-C Cable and Connector : Language Usage Guidelines from USB-IF" (PDF). Usb.org. (PDF) from the original on 2018-11-05. Retrieved 2018-12-15.
6. Hruska, Joel (2015-03-13). "USB-C vs. USB 3.1: What's the difference?". ExtremeTech. from the original on 2015-04-11. Retrieved 2015-04-09.
7. (PDF). usb.org. USB-IF. 2016-10-20. Archived from the original (PDF) on 2016-12-20.
8. "Universal Serial Bus Type-C Cable and Connector Specification" (PDF). August 2019. p. 30. Retrieved 2023-12-23.
9. Ngo, Dong. "USB Type-C: One cable to connect them all". CNET. from the original on 2017-05-11. Retrieved 2015-06-18.
10. Howse, Brett (2014-08-12). "USB Type-C Connector Specifications Finalized". from the original on 2014-12-28. Retrieved 2014-12-28.
11. "USB Type-C Cable and Connector Specification". USB Implementers Forum, Inc. from the original on 2018-11-03. Retrieved 2019-12-19.
12. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.2 (25 March 2016), table 3–1, page 37.
13. (PDF). 2014-08-12. Archived from the original (PDF) on 2014-08-14.
14. (PDF). usb.org. USB-IF. 2016-10-20. Archived from the original (PDF) on 2017-08-16. Retrieved 2018-01-03.
15. (PDF). usb.org. USB-IF. 2016-10-20. Archived from the original (PDF) on 2016-12-20.
16. "Transition existing products from USB 2.0 OTG to USB Type-C" (PDF). (PDF) from the original on 2017-10-24. Retrieved 2017-10-23.
17. "Universal Serial Bus Type-C Cable and Connector Specification, Release 2.2, October 2022". from the original on 2023-10-02. Retrieved 2023-10-04.
18. Universal Serial Bus Type-C Cable and Connector Specification Release 1.3 (14 July 2017), section A.1, page 213.
19. "USB Type-C Specification Release 1.1" (PDF). GitHub. 2015-07-13. (PDF) from the original on 2019-07-11. Retrieved 2018-11-03.
20. "USB Type-C Connectors and Cable Assemblies Compliance Document, v1.2 | USB-IF". usb.org. from the original on 2020-03-19. Retrieved 2019-05-02.
21. "USB Type-C Cable and Connector Specification Revision 1.4, March 29, 2019" (PDF). (PDF) from the original on 2020-03-20. Retrieved 2020-03-20.
22. "Universal Serial Bus Type-C Cable and Connector Specification, September 21, 2019" (PDF). (PDF) from the original on 2019-09-14. Retrieved 2019-09-21.
23. "USB Type-C Cable and Connector Specification Revision 2.1, May, 2021". from the original on 2021-05-27. Retrieved 2021-05-27.
24. "IEC 62680-1-3:2016 | IEC Webstore | energy, multimedia, cable, USB, LVDC". webstore.iec.ch. from the original on 2018-11-04. Retrieved 2018-11-03.
25. "IEC 62680-1-3:2017 | IEC Webstore | energy, multimedia, cable, USB, LVDC". webstore.iec.ch. from the original on 2018-11-04. Retrieved 2018-11-03.
26. "IEC 62680-1-3:2018 | IEC Webstore | energy, multimedia, cable, USB, LVDC". webstore.iec.ch. from the original on 2022-05-01. Retrieved 2018-11-03.
27. "USB Type-C Locking Connector Specification | USB-IF". www.usb.org. from the original on 2018-11-03. Retrieved 2018-11-03.
28. "USB Type-C Port Controller Interface Specification | USB-IF". www.usb.org. from the original on 2018-11-03. Retrieved 2018-11-03.
29. "IEC 62680-1-4:2018 | IEC Webstore". webstore.iec.ch. from the original on 2022-05-01. Retrieved 2018-11-03.
30. Shilov, Anton. "USB-IF Publishes Audio over USB Type-C Specifications". from the original on 2018-12-09. Retrieved 2018-11-03.
31. Universal Serial Bus Type-C Cable and Connector Specification Release 1.3 (14 July 2017), section 4.5.2, page 144.
32. Cunningham, Andrew (2015-01-09). "USB 3.1 and Type-C: The only stuff at CES that everyone is going to use | Ars Technica UK". ArsTechnica.co.uk. from the original on 2015-06-18. Retrieved 2015-06-18.
33. "Thunderbolt 3 – The USB-C That Does It All | Thunderbolt Technology Community". Thunderbolttechnology.net. from the original on 2015-09-05. Retrieved 2015-06-18.
34. "One port to rule them all: Thunderbolt 3 and USB Type-C join forces". from the original on 2015-06-02. Retrieved 2015-06-02.
35. "Thunderbolt 3 is twice as fast and uses reversible USB-C". 2015-06-02. from the original on 2015-06-03. Retrieved 2015-06-02.
36. Anthony, Sebastian (2015-06-02). "Thunderbolt 3 embraces USB Type-C connector, doubles bandwidth to 40Gbps". Ars Technica UK. from the original on 2015-06-03. Retrieved 2015-06-02.
37. "VESA Brings DisplayPort to New USB Type-C Connector". DisplayPort. 2014-09-22. from the original on 2015-10-05. Retrieved 2015-06-18.
38. (PDF). usb.org. USB-IF. 2016-10-20. Archived from the original (PDF) on 2016-12-20.
39. "VESA Releases Updated DisplayPort Alt Mode Spec to Bring DisplayPort 2.0 Performance to USB4 and New USB Type-C Devices". VESA - Interface Standards for The Display Industry. 2020-04-29. from the original on 2021-11-23. Retrieved 2020-10-01.
40. "MHL – Expand Your World". MHLTech.org. from the original on 2015-10-02. Retrieved 2015-06-18.
41. "MHL Alternate Mode reference design for superMHL over USB Type-C". AnandTech.com. 2016-03-15. from the original on 2017-06-04. Retrieved 2015-06-18.
42. "MHL Releases Alternate Mode for New USB Type-C Connector". MHLTech.org. 2014-11-17. from the original on 2014-11-29. Retrieved 2015-06-18.
43. "MHL Alternate Mode over USB Type-C to support superMHL". www.mhltech.org. 2015-01-06. from the original on 2016-11-15. Retrieved 2016-11-15.
44. (PDF). usb.org. MHL, LLC. 2015-11-18. Archived from the original (PDF) on 2016-09-14.
45. "HDMI Press Release: HDMI Releases Alternate Mode for USB Type-C Connector". hdmi.org. from the original on 2018-12-24. Retrieved 2016-09-10.
46. (PDF). usb.org. HDMI LLC. 2016-10-20. Archived from the original (PDF) on 2017-02-18.
47. "HDMI Alt Mode for USB Type-C Announced". anandtech.com. from the original on 2016-09-15. Retrieved 2016-09-10.
48. "A new standard will allow your USB-C devices to connect to HDMI". neowin.net. from the original on 2016-09-24. Retrieved 2016-09-10.
49. "HDMI Alt Mode for USB Type-C Connector". hdmi.org. from the original on 2016-09-19. Retrieved 2016-09-10.
50. "New Open Industry Standard Introduced for Connecting Next-Generation VR Headsets to PCs, Other Devices". GlobeNewswire News Room (Press release). 2018-07-17. from the original on 2019-02-20. Retrieved 2019-03-12.
51. Smith, Ryan (2018-07-17). "VirtualLink USB-C Alt Mode Announced: Standardized Connector for VR Headsets". AnandTech. from the original on 2018-08-21. Retrieved 2018-08-21.
52. "[802.3_DIALOG] USB-C Ethernet Alternate Mode". ieee. 2015-03-26. from the original on 2016-10-03. Retrieved 2015-11-06.
53. "Thunderbolt - the USB-C that does it all". from the original on 2022-09-10. Retrieved 2021-01-17.
54. "TECHNOLOGY BRIEF Thunderbolt 3" (PDF). 2018-09-21. (PDF) from the original on 2018-12-24. Retrieved 2018-09-20.
55. "Node Pro". 2018-09-21. from the original on 2018-09-21. Retrieved 2018-09-20.
56. "VESA RELEASES UPDATED DISPLAYPORT ALT MODE SPEC TO BRING DISPLAYPORT 2.0 PERFORMANCE TO USB4 AND NEW USB TYPE-C DEVICES". Vesa. 2020-04-29. from the original on 2021-11-23. Retrieved 2021-08-09.
57. (PDF). usb.org. USB-IF. 2016-03-11. Archived from the original (PDF) on 2016-12-20.
58. "CalDigit USB-C Cable". 2018-09-21. from the original on 2018-09-21. Retrieved 2018-09-21.
59. "VESA Brings DisplayPort to New USB Type-C Connector". www.vesa.org. from the original on 2017-02-02. Retrieved 2016-12-11.
60. "Termination Resistors Required for the USB Type-C Connector – KBA97180". 2015-04-17. from the original on 2019-07-19. Retrieved 2019-07-19.
61. "USB Charger (USB Power Delivery) | USB-IF".
62. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.3 (14 July 2017), section 2.4, page 26.
63. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.3 (14 July 2017), section 5.1.2, page 203.
64. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.3 (14 July 2017), section A, page 213.
65. "Android – Marshmallow". from the original on 2019-06-09. Retrieved 2015-10-12.
66. "Charge your Chromebook Pixel (2015)". from the original on 2019-07-11. Retrieved 2015-10-31.
67. "FreeBSD 8.2 Release Notes". www.freebsd.org. 2011-04-22. from the original on 2018-02-17. Retrieved 2018-02-05.
68. "NetBSD 7.2 Released". from the original on 2019-01-15. Retrieved 2019-01-14.
69. "OpenBSD 5.7". from the original on 2018-09-27. Retrieved 2019-06-27.
70. "Using the USB-C port and adapters on your MacBook (Retina, 12-inch, Early 2015) - Apple Support". Support.Apple.com. 2015-05-28. from the original on 2015-09-19. Retrieved 2015-06-18.
71. Microsoft. "Update for USB Type-C billboard support and Kingston thumb drive is enumerated incorrectly in Windows". from the original on 2015-12-10. Retrieved 2015-12-08.
72. Microsoft. "Windows support for USB Type-C connectors". Microsoft MSDN. from the original on 2017-06-24. Retrieved 2015-09-30.
73. "USB Dual Role Driver Stack Architecture - Windows drivers". docs.microsoft.com. from the original on 2018-11-01. Retrieved 2019-06-21.
74. Shilov, Anton. "USB-C Authentication Tech to Restrict Usage of Uncertified USB-C Accessories and Cables". AnandTech. Retrieved 2022-06-12.
75. Hollister, Sean (2022-06-06). "Apple will make USB-C accessories ask for your permission to pass data". The Verge. Retrieved 2022-06-12.
76. Li, Abner (2019-01-02). "USB-C Authentication Program could let OEMs clampdown on 'non-compliant' USB chargers". 9to5Google. Retrieved 2022-06-12.
77. Burke, Steve (2019-03-25). "Why USB 3.1 Type-C Isn't on More Cases & Cable Factory Tour in Dongguan, China". Gamers Nexus. from the original on 2019-06-26. Retrieved 2019-06-26.
78. "Are all USB-C ports for both charging and data?". 2019-09-15. from the original on 2022-09-10. Retrieved 2022-05-07.
79. "DisplayPort over USB-C". DisplayPort. from the original on 2019-11-27. Retrieved 2019-10-28.
80. Mills, Chris (2015-11-16). "A Google Engineer Is Publicly Shaming Crappy USB-C Cables". from the original on 2017-10-24. Retrieved 2017-10-23.
81. Opam, Kwame (2015-11-05). "A Google Engineer is Testing USB Type-C Cables So You Don't Have To". The Verge. from the original on 2017-10-24. Retrieved 2017-10-23.
82. "Be careful about which USB-C cables you buy off the Internet". TechnoBuffalo. 2015-11-16. from the original on 2019-12-16. Retrieved 2019-12-16.
83. Bohn, Dieter (2016-02-04). "Laptops are getting destroyed by cheap USB-C cables". The Verge. from the original on 2017-10-24. Retrieved 2017-10-23.
84. Universal Serial Bus Type-C Cable and Connector Specification Revision 1.1 (3 April 2015), page 60, table 3–13, note 1.
85. Leswing, Kif (2015-11-05). "Google Engineer Reviews Defective USB Cables on Amazon - Fortune". Fortune. from the original on 2017-05-02. Retrieved 2015-11-08.
86. "In response to the Type-C cable discussions". OnePlus Community. from the original on 2019-12-16. Retrieved 2019-12-16.
87. "TCPP01-M12 Type-C Port Protection" (PDF). (PDF) from the original on 2019-12-03. Retrieved 2019-12-03.
88. "USB-C audio: Everything you need to know". Android Central. 2018-05-02. from the original on 2019-02-24. Retrieved 2019-02-24.
89. "Bring back the headphone jack: Why USB-C audio still doesn't work". PCWorld. 2018-09-10. from the original on 2019-03-02. Retrieved 2019-03-12.
90. T, Nick (2015-02-26). "Android 5.0 Lollipop supports USB DAC audio devices, we go ears-on". Phone Arena. from the original on 2019-02-25. Retrieved 2019-02-25.
91. Schoon, Ben (2018-11-01). "Hands-on: Apple's new USB-C headphone adapter is your cheapest option for analog audio on Pixel". from the original on 2019-02-25. Retrieved 2019-02-25.
92. "Google engineer warns USB-C, Qualcomm Quick Charge are incompatible - ExtremeTech". 2016-04-25. from the original on 2017-10-26. Retrieved 2017-10-23.
93. "Qualcomm says it's fine to fast-charge your phone over USB-C". Engadget. 2016-04-25. from the original on 2017-10-24. Retrieved 2017-10-23.
94. "Qualcomm Quick Charge 4: Five minutes of charging for five hours of battery life". Qualcomm. 2016-11-17. from the original on 2017-10-24. Retrieved 2017-10-23.
95. "Apple opposes EU plans to make common charger port for all devices". The Guardian. 2021-09-23. from the original on 2021-10-18. Retrieved 2021-10-19.
96. Peltier, Elian (2021-09-23). "In a setback for Apple, the European Union seeks a common charger for all phones". The New York Times. from the original on 2022-09-10. Retrieved 2021-10-19.
97. "One common charging solution for all". Internal Market, Industry, Entrepreneurship and SMEs - European Commission. 2016-07-05. from the original on 2021-10-19. Retrieved 2021-10-19.
98. Riley, Duncan (2022-10-04). "European Parliament votes to compel USB-C charging on all portable devices". SiliconANGLE. Retrieved 2022-10-06.
99. "Long-awaited common charger for mobile devices will be a reality in 2024". European Parliament News. European Parliament. 2022-10-04. Retrieved 2022-10-06.
100. Porter, Jon (2022-10-04). "When will the iPhone be forced to use USB-C?". The Verge. The Verge. Retrieved 2022-10-06.

External links

 

Wikimedia Commons has media related to USB-C.

• The Universal Serial Bus Type-C Cable and Connector Specification is included in a set of USB documents which can be downloaded from USB.org.
• Introduction to USB Type-C, by Andrew Rogers, Microchip Technology, 2015