Nitrocellulose

"Flash paper" redirects here. For the Adobe virtual printer software discontinued in 2008, see FlashPaper.

Nitrocellulose (also known as cellulose nitrate, flash paper, flash cotton, guncotton, pyroxylin and flash string, depending on form) is a highly flammable compound formed by nitrating cellulose through exposure to a mixture of nitric acid and sulfuric acid. One of its first major uses was as guncotton, a replacement for gunpowder as propellant in firearms. It was also used to replace gunpowder as a low-order explosive in mining and other applications. In the form of collodion it was also a critical component in an early photographic emulsion, the use of which revolutionized photography in the 1860s.

Nitrocellulose^[1]

Names
Other names Cellulose nitrate; Flash paper; Flash cotton; Flash string; Gun cotton; Collodion; Pyroxylin
Identifiers
CAS Number	9004-70-0^Y
ChemSpider	none
UNII	KYR8BR2X6O^Y
Properties
Chemical formula	(C 6H 9(NO 2)O 5) n (mononitrocellulose) (C 6H 8(NO 2) 2O 5) n (dinitrocellulose) (C 6H 7(NO 2) 3O 5) n (trinitrocellulose, pictured in structures above)
Appearance	Yellowish white cotton-like filaments
Melting point	160 to 170 °C (320 to 338 °F; 433 to 443 K) (ignites)
Hazards
NFPA 704 (fire diamond)	2 3 3
Flash point	4.4 °C (39.9 °F; 277.5 K)
Lethal dose or concentration (LD, LC):
LD50 (median dose)	10 mg/kg (mouse, IV)
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa). N verify (what is ^YN ?) Infobox references

Production

The process uses a mixture of nitric acid and sulfuric acid to convert cellulose into nitrocellulose.^[2] The quality of the cellulose is important. Hemicellulose, lignin, pentosans, and mineral salts give inferior nitrocelluloses. In precise chemical terms, nitrocellulose is not a nitro compound, but a nitrate ester. The glucose repeat unit (anhydroglucose) within the cellulose chain has three OH groups, each of which can form a nitrate ester. Thus, nitrocellulose can denote mononitrocellulose, dinitrocellulose, and trinitrocellulose, or a mixture thereof. With fewer OH groups than the parent cellulose, nitrocelluloses do not aggregate by hydrogen bonding. The overarching consequence is that the nitrocellulose is soluble in organic solvents such as acetone and esters, e.g ethyl acetate, methyl acetate, ethyl carbonate.^[3] Most lacquers are prepared from the dinitrate whereas explosives are mainly the trinitrate.^[4][5]

The chemical equation for the formation of the trinitrate is:

3 HNO₃ + C₆H₇(OH)₃O₂ H₂SO₄→ C₆H₇(ONO₂)₃O₂ + 3 H₂O

The yields are about 85%, with losses attributed to complete oxidation of the cellulose to oxalic acid.

Use

The principal uses of cellulose nitrate is for the production of lacquers and coatings, explosives, and celluloid.^[6]

In terms of lacquers and coatings, nitrocellulose dissolves readily in organic solvents, which upon evaporation leave a colorless, transparent, flexible film.^[4] Nitrocellulose lacquers have been used as a finish on furniture and musical instruments.^[7] used nitrocellulose both as a clear finish over wood-stained guitars and as Guncotton, dissolved at about 25% in acetone, forms a lacquer used in preliminary stages of wood finishing to develop a hard finish with a deep lustre.^[8] It is normally the first coat applied, sanded and followed by other coatings that bond to it.

The explosive applications are diverse. Relative to coatings applications, the nitrate content is higher for propellant applications typically.^[6] For space flight, nitrocellulose was used by Copenhagen Suborbitals on several missions as a means of jettisoning components of the rocket/space capsule and deploying recovery systems. However, after several missions and flights, it proved not to have the desired explosive properties in a near vacuum environment.^[9] In 2014, the Philae comet lander failed to deploy its harpoons due to its 0.3 grams of nitrocellulose propulsion charges failing to fire during the landing.

Nail polish is made from nitrocellulose lacquer as it is inexpensive, dries quickly, and is not damaging to skin.^[10]

Other uses

Collodion, a solution of nitrocellulose is used today in topical skin applications, such as liquid skin and in the application of salicylic acid, the active ingredient in Compound W wart remover.

Laboratory uses

• Membrane filters made of a mesh of nitrocellulose threads with various porosity are used in laboratory procedures for particle retention and cell capture in liquid or gaseous solutions and, reversely, obtaining particle-free filtrates.^[11]
• A nitrocellulose slide, nitrocellulose membrane, or nitrocellulose paper is a sticky membrane used for immobilizing nucleic acids in Southern blots and northern blots. It is also used for immobilization of proteins in western blots and atomic force microscopy^[12] for its nonspecific affinity for amino acids. Nitrocellulose is widely used as support in diagnostic tests where antigen-antibody binding occurs, e.g., pregnancy tests, U-albumin tests and CRP. Glycine and chloride ions make protein transfer more efficient.
• Radon tests for alpha track etches use nitrocellulose.
• Adolph Noé developed a method of peeling coal balls using nitrocellulose.^[13]
• It is used to coat playing cards and to bind staples together in office staplers.

Hobbies

• In 1851, Frederick Scott Archer invented the wet collodion process as a replacement for albumen in early photographic emulsions, binding light-sensitive silver halides to a glass plate.^[14]
• Magicians' flash papers are sheets of paper or cloth made from nitrocellulose, which burn almost instantly with a bright flash, leaving no ash.
• As a medium for cryptographic one-time pads, they make the disposal of the pad complete, secure, and efficient.
• Nitrocellulose lacquer is spin-coated onto aluminium or glass discs, then a groove is cut with a lathe, to make one-off phonograph records, used as masters for pressing or for play in dance clubs. They are referred to as acetate discs.
• Depending on the manufacturing process, nitrocellulose is esterified to varying degrees. Table tennis balls, guitar picks, and some photographic films have fairly low esterification levels and burn comparatively slowly with some charred residue.

 

Table tennis ball, prepared from nitrocellulose (Celluloid)

• In 1846, nitrated cellulose was found to be soluble in ether and alcohol. The solution was named collodion and was soon used as a dressing for wounds.^[15][16]

Historical uses

Early work on nitration of cellulose

 

Pure nitrocellulose

 

Workman operating a guncotton press behind a protective rope screen, 1909

Deflagration test of nitrocellulose in slow motion

In 1832 Henri Braconnot discovered that nitric acid, when combined with starch or wood fibers, would produce a lightweight combustible explosive material, which he named xyloïdine.^[17] A few years later in 1838, another French chemist, Théophile-Jules Pelouze (teacher of Ascanio Sobrero and Alfred Nobel), treated paper and cardboard in the same way.^[18] Jean-Baptiste Dumas obtained a similar material, which he called nitramidine.^[19]

Guncotton

Around 1846 Christian Friedrich Schönbein, a German-Swiss chemist, discovered a more practical formulation.^[20] As he was working in the kitchen of his home in Basel, he spilled a mixture of nitric acid (HNO₃) and sulfuric acid (H₂SO₄) on the kitchen table. He reached for the nearest cloth, a cotton apron, and wiped it up. He hung the apron on the stove door to dry, and as soon as it was dry, a flash occurred as the apron ignited. His preparation method was the first to be widely used. The method was to immerse one part of fine cotton in 15 parts of an equal blend of sulfuric acid and nitric acid. After two minutes, the cotton was removed and washed in cold water to set the esterification level and to remove all acid residue. The cotton was then slowly dried at a temperature below 40 °C (104 °F). Schönbein collaborated with the Frankfurt professor Rudolf Christian Böttger, who had discovered the process independently in the same year.

By coincidence, a third chemist, the Brunswick professor F. J. Otto had also produced guncotton in 1846 and was the first to publish the process, much to the disappointment of Schönbein and Böttger.^{[21][full citation needed]}

The patent rights for the manufacture of guncotton were obtained by John Hall & Son in 1846, and industrial manufacture of the explosive began at a purpose-built factory at Marsh Works in Faversham, Kent, a year later. The manufacturing process was not properly understood and few safety measures were put in place. A serious explosion that July killed almost two dozen workers, resulting in the immediate closure of the plant. Guncotton manufacture ceased for over 15 years until a safer procedure could be developed.^[22]

The British chemist Frederick Augustus Abel developed the first safe process for guncotton manufacture, which he patented in 1865. The washing and drying times of the nitrocellulose were both extended to 48 hours and repeated eight times over. The acid mixture was changed to two parts sulfuric acid to one part nitric. Nitration can be controlled by adjusting acid concentrations and reaction temperature. Nitrocellulose is soluble in a mixture of ethanol and ether until nitrogen concentration exceeds 12%. Soluble nitrocellulose, or a solution thereof, is sometimes called collodion.^[23]

Guncotton containing more than 13% nitrogen (sometimes called insoluble nitrocellulose) was prepared by prolonged exposure to hot, concentrated acids^[23] for limited use as a blasting explosive or for warheads of underwater weapons such as naval mines and torpedoes.^[24] Safe and sustained production of guncotton began at the Waltham Abbey Royal Gunpowder Mills in the 1860s, and the material rapidly became the dominant explosive, becoming the standard for military warheads, although it remained too potent to be used as a propellant. More-stable and slower-burning collodion mixtures were eventually prepared using less concentrated acids at lower temperatures for smokeless powder in firearms. The first practical smokeless powder made from nitrocellulose, for firearms and artillery ammunition, was invented by French chemist Paul Vieille in 1884.

Jules Verne viewed the development of guncotton with optimism. He referred to the substance several times in his novels. His adventurers carried firearms employing this substance. In his From the Earth to the Moon, guncotton was used to launch a projectile into space.

Because of their fluffy and nearly white appearance, nitrocellulose products are often referred to as cottons, e.g. lacquer cotton, celluloid cotton, and gun cotton.^[4]

Guncotton was originally made from cotton (as the source of cellulose) but contemporary methods use highly processed cellulose from wood pulp. While guncotton is dangerous to store, the hazards it presents can be minimized by storing it dampened with various liquids, such as alcohol. For this reason, accounts of guncotton usage dating from the early 20th century refer to "wet guncotton."

 

Jam tin grenades were made in World War I using gun cotton

The power of guncotton made it suitable for blasting. As a projectile driver, it had around six times the gas generation of an equal volume of black powder and produced less smoke and less heating.

Artillery shells filled with gun cotton were widely used during the American Civil War, and its use was one of the reasons the conflict was seen as the "first modern war."^[25] In combination with breech-loading artillery, such high explosive shells could cause greater damage than previous solid cannonballs.

During the first World War, British authorities were slow to introduce grenades, with soldiers at the front improvising by filling ration tin cans with gun cotton, scrap and a basic fuse.^[26]

Further research indicated the importance of washing the acidified cotton. Unwashed nitrocellulose (sometimes called pyrocellulose) may spontaneously ignite and explode at room temperature, as the evaporation of water results in the concentration of unreacted acid.^[24]

Film

See also: Film base § Nitrate

 

Nitrocellulose film on a light box, showing deterioration, from Library and Archives Canada collection

In 1855, the first man-made plastic, nitrocellulose (branded Parkesine, patented in 1862), was created by Alexander Parkes from cellulose treated with nitric acid and a solvent. In 1868, American inventor John Wesley Hyatt developed a plastic material he named Celluloid, improving on Parkes' invention by plasticizing the nitrocellulose with camphor so that it could be processed into a photographic film. This was used commercially as "celluloid", a highly flammable plastic that until the mid-20th century formed the basis for lacquers and photographic film.^[8]

On May 2, 1887, Hannibal Goodwin filed a patent for "a photographic pellicle and process of producing same ... especially in connection with roller cameras", but the patent was not granted until September 13, 1898.^[27] In the meantime, George Eastman had already started production of roll-film using his own process.

Nitrocellulose was used as the first flexible film base, beginning with Eastman Kodak products in August 1889. Camphor is used as a plasticizer for nitrocellulose film, often called nitrate film. Goodwin's patent was sold to Ansco, which successfully sued Eastman Kodak for infringement of the patent and was awarded $5,000,000 in 1914 to Goodwin Film.^[28]

Nitrate film fires

Disastrous fires related to celluloid or "nitrate film" became regular occurrences in the motion picture industry throughout the silent era and for many years after the arrival of sound film.^[29] Projector fires and spontaneous combustion of nitrate footage stored in studio vaults and in other structures were often blamed during the early to mid 20th century for destroying or heavily damaging cinemas, inflicting many serious injuries and deaths, and for reducing to ashes the master negatives and original prints of tens of thousands of screen titles,^[30] turning many of them into lost films. Even on the occasions when nitrate stock did not start a devastating blaze, once flames from other sources spread to large nearby film collections, the resulting combustion greatly intensified the fires and substantially increased the scope of their damage.

During the year 1914—the same year that Goodwin Film was awarded $5,000,000 from Kodak for patent infringement—nitrate film fires incinerated a significant portion of the United States' early cinematic history. In that year alone, five very destructive fires occurred at four major studios and a film-processing plant. Millions of feet of film burned on March 19 at the Eclair Moving Picture Company in Fort Lee, New Jersey.^[31] Later that same month, many more reels and film cans of negatives and prints also burned at Edison Studios in New York City, in the Bronx; then again, on May 13, a fire at Universal Pictures' Colonial Hall "film factory" in Manhattan consumed another extensive collection.^[32][33] Yet again, on June 13 in Philadelphia, a fire and a series of explosions ignited inside the 186-square-meter (2,000-square-foot) film vault of the Lubin Manufacturing Company and quickly wiped out virtually all of that studio's pre-1914 catalogue.^[34] Then a second fire hit the Edison Company at another location on December 9, at its film-processing complex in West Orange, New Jersey. That fire, a catastrophic one, started inside a film-inspection building and caused over $7,000,000 in property damages ($189,000,000 today).^[35] Even after film technology changed, archives of older films remained vulnerable; the 1965 MGM vault fire burned many films that were decades old.

 

Lubin film vault custodian Stanley Lowry (foreground) surveys the rubble after fire and explosions, June 1914.

The use of volatile nitrocellulose film for motion pictures led many cinemas to fireproof their projection rooms with wall coverings made of asbestos. Those additions intended to prevent or at least delay the migration of flames beyond the projection areas. A training film for projectionists included footage of a controlled ignition of a reel of nitrate film, which continued to burn even when fully submerged in water.^[36] Once burning, it is extremely difficult to extinguish. Unlike most other flammable materials, nitrocellulose does not need a source of air to continue burning, since it contains sufficient oxygen within its molecular structure to sustain a flame. For this reason, immersing burning film in water may not extinguish it, and could actually increase the amount of smoke produced.^[37][38] Owing to public safety precautions, London Underground forbade transport of movies on its system until well past the introduction of safety film.

Cinema fires caused by the ignition of nitrocellulose film stock commonly occurred as well. In Ireland in 1926, it was blamed for the Dromcolliher cinema tragedy in County Limerick in which 48 people died. Then in 1929 at the Glen Cinema in Paisley, Scotland, a film-related fire killed 69 children. Today, nitrate film projection is rare and normally highly regulated and requires extensive precautions, including extra health-and-safety training for projectionists. A special projector certified to run nitrate films has many modifications, among them the chambering of the feed and takeup reels in thick metal covers with small slits to allow the film to run through them. The projector is additionally modified to accommodate several fire extinguishers with nozzles aimed at the film gate. The extinguishers automatically trigger if a piece of film near the gate starts to burn. While this triggering would likely damage or destroy a significant portion of the projector's components, it would contain a fire and prevent far greater damage. Projection rooms may also be required to have automatic metal covers for the projection windows, preventing the spread of fire to the auditorium. Today, the Dryden Theatre at the George Eastman Museum is one of a few theaters in the world that is capable of safely projecting nitrate films and regularly screens them to the public.^[39][40]

The use of nitrate film and the looming threat of its fiery potential were certainly not issues limited to the realm of motion pictures or to commercial still photography. The film was also used for many years in the field of medicine, where its hazardous nature was most acute, especially in its application to X-ray photography.^[8] In 1929, several tons of stored X-ray film were ignited by steam from a broken heating pipe at the Cleveland Clinic in Ohio. That tragedy claimed 123 lives during the fire and additional fatalities several days later, when hospitalized victims died due to inhaling excessive amounts of smoke from the burning film, which was laced with toxic gases such as sulfur dioxide and hydrogen cyanide.^[41][42] Related fires in other medical facilities prompted the growing disuse of nitrocellulose stock for X-rays by 1933, nearly two decades before its use was discontinued for motion-picture films in favour of cellulose acetate film, more commonly known as "safety film".

 

Decayed nitrate film, EYE Film Institute Netherlands

Nitrocellulose decomposition and new "safety" stocks

Nitrocellulose was found to gradually decompose, releasing nitric acid and further catalyzing the decomposition (eventually into a flammable powder). Decades later, storage at low temperatures was discovered as a means of delaying these reactions indefinitely. The great majority of films produced during the early 20th century are thought to have been lost either through this accelerating, self-catalyzed disintegration or through studio warehouse fires. Salvaging old films is a major problem for film archivists (see film preservation).

Nitrocellulose film base manufactured by Kodak can be identified by the presence of the word "nitrate" in dark letters along one edge; the word only in clear letters on a dark background indicates derivation from a nitrate base original negative or projection print, but the film in hand itself may be a later print or copy negative, made on safety film. Acetate film manufactured during the era when nitrate films were still in use was marked "Safety" or "Safety Film" along one edge in dark letters. 8, 9.5, and 16 mm film stocks, intended for amateur and other nontheatrical use, were never manufactured with a nitrate base in the west, but rumors exist of 16 mm nitrate film having been produced in the former Soviet Union and China.^[43]

Nitrate dominated the market for professional-use 35 mm motion picture film from the industry's origins to the early 1950s. While cellulose acetate-based safety film, notably cellulose diacetate and cellulose acetate propionate, was produced in the gauge for small-scale use in niche applications (such as printing advertisements and other short films to enable them to be sent through the mails without the need for fire safety precautions), the early generations of safety film base had two major disadvantages relative to nitrate: it was much more expensive to manufacture, and considerably less durable in repeated projection. The cost of the safety precautions associated with the use of nitrate was significantly lower than the cost of using any of the safety bases available before 1948. These drawbacks were eventually overcome with the launch of cellulose triacetate base film by Eastman Kodak in 1948.^[44] Cellulose triacetate superseded nitrate as the film industry's mainstay base very quickly. While Kodak had discontinued some nitrate film stocks earlier, it stopped producing various nitrate roll films in 1950 and ceased production of nitrate 35 mm motion picture film in 1951.^[45]

The crucial advantage cellulose triacetate had over nitrate was that it was no more of a fire risk than paper (the stock is often referred to as "non-flam": this is true—but it is combustible, just not in as volatile or as dangerous a way as nitrate), while it almost matched the cost and durability of nitrate. It remained in almost exclusive use in all film gauges until the 1980s, when polyester/PET film began to supersede it for intermediate and release printing.^[46]

Polyester is much more resistant to polymer degradation than either nitrate or triacetate. Although triacetate does not decompose in as dangerous a way as nitrate does, it is still subject to a process known as deacetylation, often nicknamed "vinegar syndrome" (due to the acetic acid smell of decomposing film) by archivists, which causes the film to shrink, deform, become brittle and eventually unusable.^[47] PET, like cellulose mononitrate, is less prone to stretching than other available plastics.^[46] By the late 1990s, polyester had almost entirely superseded triacetate for the production of intermediate elements and release prints.

Triacetate remains in use for most camera negative stocks because it can be "invisibly" spliced using solvents during negative assembly, while polyester film is usually spliced using adhesive tape patches, which leave visible marks in the frame area. However, ultrasonic splicing in the frame line area can be invisible. Also, polyester film is so strong, it will not break under tension and may cause serious damage to expensive camera or projector mechanisms in the event of a film jam, whereas triacetate film breaks easily, reducing the risk of damage. Many were opposed to the use of polyester for release prints for this reason, and because ultrasonic splicers are very expensive, beyond the budgets of many smaller theaters. In practice, though, this has not proved to be as much of a problem as was feared. Rather, with the increased use of automated long-play systems in cinemas, the greater strength of polyester has been a significant advantage in lessening the risk of a film performance being interrupted by a film break.^{[citation needed]}

Despite its self-oxidizing hazards, nitrate is still regarded highly as the stock is more transparent than replacement stocks, and older films used denser silver in the emulsion. The combination results in a notably more luminous image with a high contrast ratio.^[48]

Fabric

The solubility of nitrocellulose was the basis for the first "artificial silk" by Georges Audemars in 1855, which he called "Rayon".^{[citation needed]}. However, Hilaire de Chardonnet was the first to patent a nitrocellulose fiber marketed as "artificial silk" at the Paris Exhibition of 1889.^[49] Commercial production started in 1891, but the result was flammable and more expensive than cellulose acetate or cuprammonium rayon. Because of this predicament, production ceased early in the 1900s. Nitrocellulose was briefly known as "mother-in-law silk".^[50]

Frank Hastings Griffin invented the double-godet, a special stretch-spinning process that changed artificial silk to rayon, rendering it usable in many industrial products such as tire cords and clothing.^[51] Nathan Rosenstein invented the "spunize process" by which he turned rayon from a hard fiber to a fabric. This allowed rayon to become a popular raw material in textiles.

Coatings

Nitrocellulose lacquer manufactured by (among others) DuPont, was the primary material for painting automobiles for many years. Durability of finish, complexities of "multiple stage" modern finishes, and other factors including environmental regulation led manufacturers to choose newer technologies. It remained the favorite of hobbyists for both historical reasons and for the ease with which a professional finish can be obtained. Most automobile "touch up" paints are still made from lacquer because of its fast drying, easy application, and superior adhesion properties – regardless of the material used for the original finish. Guitars sometimes shared color codes with current automobiles. It fell out of favor for mass production use for a number of reasons including environmental regulation and the cost of application vs. "poly" finishes. However, both Fender and Gibson still use nitrocellulose lacquers in their "Custom" shops when reproducing historically accurate guitars. The nitrocellulose lacquer yellows and cracks over time, and custom shops will reproduce this aging to make instruments appear vintage. Guitars made by smaller shops (luthiers) also often use "nitro" as it has an almost mythical status among guitarists.

Hazards

'United States Inter-Agency Committee for Nitrate Film Vault Tests' – film transfer from 1948 about testing storage and flame suppression methods of nitrate film stock; runtime 00:08:41

Because of its explosive nature, not all applications of nitrocellulose were successful. In 1869, with elephants having been poached to near extinction, the billiards industry offered a US$10,000 prize to whomever came up with the best replacement for ivory billiard balls. John Wesley Hyatt created the winning replacement, which he created with a new material he invented, called camphored nitrocellulose—the first thermoplastic, better known as Celluloid. The invention enjoyed a brief popularity, but the Hyatt balls were extremely flammable, and sometimes portions of the outer shell would explode upon impact. An owner of a billiard saloon in Colorado wrote to Hyatt about the explosive tendencies, saying that he did not mind very much personally but for the fact that every man in his saloon immediately pulled a gun at the sound.^[52][53] The process used by Hyatt to manufacture the billiard balls, patented in 1881,^[54] involved placing the mass of nitrocellulose in a rubber bag, which was then placed in a cylinder of liquid and heated. Pressure was applied to the liquid in the cylinder, which resulted in a uniform compression on the nitrocellulose mass, compressing it into a uniform sphere as the heat vaporized the solvents. The ball was then cooled and turned to make a uniform sphere. In light of the explosive results, this process was called the "Hyatt gun method".^[55]

An overheated container of dry nitrocellulose is believed to be the initial cause of the 2015 Tianjin explosions.^[56]

See also

• Pentaerythritol tetranitrate (PETN), a related explosive.
• Cordite
• Nitroglycerine
• Nitrostarch
• RE factor

References

1. Merck Index (11th ed.). p. 8022.
2. "How to make flash paper and flash cotton from household products". vadcpa.com/Val/Projects.php. Retrieved 11 January 2022.
3. "Wildlife Toxicity Assessments for Chemicals of Military Concern | ScienceDirect". www.sciencedirect.com. Retrieved 22 July 2021.
4. Balser, Klaus; Hoppe, Lutz; Eicher, Theo; Wandel, Martin; Astheimer, Hans‐Joachim; Steinmeier, Hans; Allen, John M. (2004). "Cellulose Esters". Ullmann's Encyclopedia of Industrial Chemistry. Weinheim: Wiley-VCH. doi:10.1002/14356007.a05_419.pub2.
5. Urbanski, Tadeusz (1965). Chemistry and Technology of Explosives. Vol. 1. Oxford: Pergamon Press. pp. 20–21.
6. Saunders, C. W.; Taylor, L. T. (1990). "A review of the synthesis, chemistry and analysis of nitrocellulose". Journal of Energetic Materials. 8 (3): 149–203. Bibcode:1990JEnM....8..149S. doi:10.1080/07370659008012572.
7. . Archived from the original on 30 March 2008. Retrieved 15 January 2008.
8. . Dow Chemical. Archived from the original on 22 July 2017. Retrieved 19 January 2014.
9. Bengtson, Kristian von (21 October 2013). "In Space No One Can Hear your Nitrocellulose Explode". Wired.
10. Schneider, Günther; Gohla, Sven; Schreiber, Jörg; Kaden, Waltraud; Schönrock, Uwe; Schmidt‐Lewerkühne, Hartmut; Kuschel, Annegret; Petsitis, Xenia; Pape. "Skin Cosmetics". Ullmann's Encyclopedia of Industrial Chemistry. Weinheim: Wiley-VCH. doi:10.1002/14356007.a24_219.
11. "Sartorius Membrane filters".
12. Kreplak, L.; et al. (2007). "Atomic Force Microscopy of Mammalian Urothelial Surface". Journal of Molecular Biology. 374 (2): 365–373. doi:10.1016/j.jmb.2007.09.040. PMC 2096708. PMID 17936789.
13. Kraus, E. J. (September 1939). "Adolf Carl Noe". Botanical Gazette. 101 (1): 231. Bibcode:1939Sci....89..379C. doi:10.1086/334861. JSTOR 2472034. S2CID 84787772.
14. Leggat, R. "The Collodion Process". A History of Photography.
15. Schönbein, C. F. (1849). "On ether glue or liquor constringens; and its uses in surgery". The Lancet. 1 (1333): 289–290. doi:10.1016/s0140-6736(02)66777-7.
16. Maynard, John Parker (1848). "Discovery and application of the new liquid adhesive plaster". The Boston Medical and Surgical Journal. 38 (9): 178–183. doi:10.1056/nejm184803290380903.
17. Braconnot, Henri (1833). "De la transformation de plusieurs substances végétales en un principe nouveau" [On the transformation of several vegetable substances into a new substance]. Annales de Chimie et de Physique. 52: 290–294. On page 293, Braconnot names nitrocellulose xyloïdine
18. Pelouze, Théophile-Jules (1838). "Sur les produits de l'action de l'acide nitrique concentré sur l'amidon et le ligneux" [On the products of the action of concentrated nitric acid on starch and wood]. Comptes Rendus. 7: 713–715.
19. Dumas, Jean-Baptiste (1843). Traité de Chimie Appliquée aux Arts. Vol. 6. Paris: Bechet Jeune. p. 90. Il y a quelques années, M. Braconnot reconnut que l'acide nitrique concentré, convertit l'amidon, le ligneux, la cellulose, et quelques autres substances en un matière qu'il nomma xyloïdine, et que j'appellerai nitramidine. [Some years ago, Mr. Braconnot recognized that concentrated nitric acid converted starch, wood, cellulose, and some other substances into a material that he called xyloïdine, and that I will call nitramidine.]
20. Schönbein first communicated his discovery to the Naturforschende Gesellschaft of Basel, Switzerland on March 11, 1846:
    • Schönbein, Christian Friedrich (11 March 1846). "Notiz über eine Veränderung der Pflanzenfaser und einiger andern organischen Substanzen" [Notice on a change of plant fibers and some other organic substances]. Bericht über die Verhandlungen der Naturforschenden Gesellschaft in Basel. 7: 26–27.
    • Schönbein, Christian Friedrich (27 May 1846). "Ueber Schiesswolle" [On guncotton]. Bericht über die Verhandlungen der Naturforschenden Gesellschaft in Basel. 7: 27.
    In a letter, he subsequently communicated his discovery to the French Academy of Sciences:
    • Schönbein, Christian Friedrich (1846). "Lettre de M. Schoenbein à M. Dumas". Comptes Rendus. 23: 678–679.
21. Itzehoer Wochenblatt, 29 October 1846, col. 1626ff.
22. Ponting, Clive (2011). Gunpowder: An Explosive History – from the Alchemists of China to the Battlefields of Europe. Random House. ISBN 9781448128112.
23. Brown, G. I. (1998). The Big Bang: A History of Explosives. Sutton Publishing. p. 132. ISBN 978-0-7509-1878-7.
24. Fairfield, A. P.; CDR USN (1921). Naval Ordnance. Lord Baltimore Press. pp. 28–31.
25. Bennett, Matthew (17 February 2011). "Explosives in War". BBC History. Retrieved 9 April 2021.
26. Westwell, Ian (2008). The Ultimate Illustrated History of World War I. Hermes House. p. 131. ISBN 978-0-681-54134-4.
27. U.S. Patent 610,861
28. "Kodak Concern to Make Big Payment to Goodwin Company". The New York Times. 27 March 1914. Retrieved 18 September 2010. A settlement has been reached between the Goodwin Film and Camera Company and the Eastman Kodak Company concerning the suit brought in the Federal District Court by the former for an accounting of the profits derived from the sale of photographic films prepared according to the patent taken out by the late Rev. Hannibal Goodwin of Newark in 1898. The details of it have not been announced, but it is understood to provide for tile payment of a large sum of money by ...
29. Kahana, Yoram (2016). "Dangerous Beauty: Nitrate Films Return To Hollywood, Thanks To The HFPA", online news article, Hollywood Foreign Press Association (HFPA) / Golden Globes, West Hollywood, California, published 9 November 2016. Retrieved 5 October 2021.
30. "Lubin's Big Blaze", Variety, 19 June 1914, p. 20. Internet Archive (hereinafter cited "I.A."), San Francisco, California. Retrieved 10 October 2021.
31. "Eclair Plant Burns", Motography (Chicago), 4 April 1914, p. 243. I.A. Retrieved 9 October 2021.
32. "'Movie' Films Burn With Edison Studio", The New York Times, 29 March 1914, p. 13. ProQuest Historical Newspapers (hereinafter cited "ProQuest"), Ann Arbor, Michigan, subscription access through the University of North Carolina at Chapel Hill Library.
33. "Universal's Factory Gutted By Disastrous Conflagration", New York Clipper, 23 May 1914, p. 15. I.A. Retrieved 11 October 2021.
34. "Big Fire At Lubin Plant", The Moving Picture World, 27 June 1914, p. 1803. I.A. Retrieved 10 October 2021. See Wikipedia page "1914 Lubin vault fire".
35. "Fire Originated in Building in Which Films Were Inspected", New York World (Manhattan), 10 December 1914, p. 1. ProQuest.
36. Kermode, Mark (1 May 2012). The Good, the Bad and the Multiplex. Random House. p. 3. ISBN 9780099543497.
37. Health and Safety Executive leaflet/cellulose.pdf
38. ^{[dead link]}Interesting discussion on NC films. 2014-12-17 at the Wayback Machine
39. . Pro-Tek Vaults. 4 June 2015. Archived from the original on 12 March 2016. Retrieved 11 March 2016.
40. . George Eastman Museum. Archived from the original on 12 March 2016. Retrieved 11 March 2016.
41. Clifton, Brad. "The Cleveland Clinic X-Ray Fire of 1929". Cleveland Historical. Retrieved 1 April 2015.
42. Feinstein, John and Sharon Conway (1978). "Historic Film Lost in Blaze", Washington Post, 8 December 1978, p. 1A. ProQuest. This article about the 1978 film fire at the National Archives warehouse in Suitland, Maryland, describes some of the toxic gases emitted by burning nitrate film.
43. Cleveland, David (2002). "Don't Try This at Home: Some Thoughts on Nitrate Film, With Particular Reference to Home Movie Systems". In Smither, Roger; Surowiec, Catherine (eds.). This Film is Dangerous: A Celebration of Nitrate Film. Brussels: FIAF. p. 196. ISBN 978-2-9600296-0-4.
44. Fordyce, Charles; et al. (October 1948). "Improved Safety Motion Picture Film Support". Journal of the Society of Motion Picture Engineers. 51 (4): 331–350. doi:10.5594/j11731.
45. Shanebrook, Robert L. (2016). Making Kodak Film (Expanded second ed.). Rochester, NY: Robert L. Shanebrook. p. 82. ISBN 978-0-615-41825-4.
46. Van Schil, George J. (February 1980). "The Use of Polyester Film Base in the Motion Picture Industry — a Market Survey". SMPTE Journal. 89 (2): 106–110. doi:10.5594/j00526.
47. Greco, JoAnn (12 November 2018). "Saving Old Movies". Distillations. Science History Institute. 4 (3): 36–39. Retrieved 23 April 2020.
48. Case, Jared. . YouTube. Archived from the original on 6 May 2015. Retrieved 10 March 2015.
49. Garrett, Alfred (1963). The Flash of Genius. Princeton, New Jersey: D. Van Nostrand Company, Inc. pp. 48–49.
50. Editors, Time-Life (1991). Inventive Genius. New York: Time-Life Books. p. 52. ISBN 978-0-8094-7699-2. {{cite book}}: |last= has generic name (help)
51. Cook, Bonnie L. "F. Hastings Griffin Jr., 95, lawyer and star athlete". www.philly.com. Retrieved 4 August 2018.
52. Connections, James Burke, Volume 9, "Countdown", 29:00–31:45, 1978
53. United States. National Resources Committee (1941). Research: A National Resource. USGPO. p. 29.
54. U.S. Patent 239,792
55. Worden, Edward Chauncey (1911). Nitrocellulose Industry. Vol. 2. D. Van Nostrand Company. pp. 726–727.
56. "Chinese Investigators Identify Cause Of Tianjin Explosion". Chemical & Engineering News. 8 February 2016. The immediate cause of the accident was the spontaneous ignition of overly dry nitrocellulose stored in a container that overheated

External links

•   Media related to Nitrocellulose at Wikimedia Commons

 

Wikisource has original text related to this article:

Harper's New Monthly Magazine/Vol. XLIV/No. 261/February 1872/Editor's Scientific Record/Explosion of Gun-Cotton at Stowmarket

•  Animation portal

• Gun Cotton at The Periodic Table of Videos (University of Nottingham)
• Cellulose, nitrate (Nitrocellulose)—ChemSub Online
• How To Make Nitro-Cellulose That Works