Floppy disk

"Floppy" redirects here. For other uses, see Floppy (disambiguation).

A floppy disk or floppy diskette (casually referred to as a floppy or a diskette) is a type of disk storage composed of a thin and flexible disk of a magnetic storage medium in a square or nearly square plastic enclosure lined with a fabric that removes dust particles from the spinning disk. Floppy disks store digital data which can be read and written when the disk is inserted into a floppy disk drive (FDD) connected to or inside a computer or other device.

8-inch, 5+1⁄4-inch, and 3+1⁄2-inch floppy disks

8-inch, 5+1⁄4-inch (full height), and 3+1⁄2-inch drives

A 3+1⁄2-inch floppy disk removed from its housing

The first floppy disks, invented and made by IBM, had a disk diameter of 8 inches (203.2 mm).^[1] Subsequently, the 5¼-inch and then the 3½-inch became a ubiquitous form of data storage and transfer into the first years of the 21st century.^[2] 3½-inch floppy disks can still be used with an external USB floppy disk drive. USB drives for 5¼-inch, 8-inch, and other-size floppy disks are rare to non-existent. Some individuals and organizations continue to use older equipment to read or transfer data from floppy disks.

Floppy disks were so common in late 20th-century culture that many electronic and software programs continue to use save icons that look like floppy disks well into the 21st century, as a form of skeuomorphic design. While floppy disk drives still have some limited uses, especially with legacy industrial computer equipment, they have been superseded by data storage methods with much greater data storage capacity and data transfer speed, such as USB flash drives, memory cards, optical discs, and storage available through local computer networks and cloud storage.

History

 

8-inch floppy disk,
inserted in drive,
(3½-inch floppy diskette,
in front, shown for scale)

 

3½-inch, high-density floppy diskettes with adhesive labels affixed

Main article: History of the floppy disk

The first commercial floppy disks, developed in the late 1960s, were 8 inches (203.2 mm) in diameter;^[1][2] they became commercially available in 1971 as a component of IBM products and both drives and disks were then sold separately starting in 1972 by Memorex and others.^[3] These disks and associated drives were produced and improved upon by IBM and other companies such as Memorex, Shugart Associates, and Burroughs Corporation.^[4] The term "floppy disk" appeared in print as early as 1970,^[5] and although IBM announced its first media as the Type 1 Diskette in 1973, the industry continued to use the terms "floppy disk" or "floppy".

In 1976, Shugart Associates introduced the 5¼-inch FDD. By 1978, there were more than ten manufacturers producing such FDDs.^[6] There were competing floppy disk formats, with hard- and soft-sector versions and encoding schemes such as differential Manchester encoding (DM), modified frequency modulation (MFM), M²FM and group coded recording (GCR). The 5¼-inch format displaced the 8-inch one for most uses, and the hard-sectored disk format disappeared. The most common capacity of the 5¼-inch format in DOS-based PCs was 360 KB (368,640 bytes) for the Double-Sided Double-Density (DSDD) format using MFM encoding. In 1984, IBM introduced with its PC/AT the 1.2 MB (1,228,800 bytes) dual-sided 5¼-inch floppy disk, but it never became very popular. IBM started using the 720 KB double density 3½-inch microfloppy disk on its Convertible laptop computer in 1986 and the 1.44 MB high-density version with the IBM Personal System/2 (PS/2) line in 1987. These disk drives could be added to older PC models. In 1988, Y-E Data introduced a drive for 2.88 MB Double-Sided Extended-Density (DSED) diskettes which was used by IBM in its top-of-the-line PS/2 and some RS/6000 models and in the second-generation NeXTcube and NeXTstation; however, this format had limited market success due to lack of standards and movement to 1.44 MB drives.^[7]

Throughout the early 1980s, limits of the 5¼-inch format became clear. Originally designed to be more practical than the 8-inch format, it was becoming considered too large; as the quality of recording media grew, data could be stored in a smaller area.^[8] Several solutions were developed, with drives at 2-, 2½-, 3-, 3¼-,^[9] 3½- and 4-inches (and Sony's 90 mm × 94 mm (3.54 in × 3.70 in) disk) offered by various companies.^[8] They all had several advantages over the old format, including a rigid case with a sliding metal (or later, sometimes plastic) shutter over the head slot, which helped protect the delicate magnetic medium from dust and damage, and a sliding write protection tab, which was far more convenient than the adhesive tabs used with earlier disks. The large market share of the well-established 5¼-inch format made it difficult for these diverse mutually-incompatible new formats to gain significant market share.^[8] A variant on the Sony design, introduced in 1982 by many manufacturers, was then rapidly adopted. By 1988, the 3½-inch was outselling the 5¼-inch.^[10]

Generally, the term floppy disk persisted, even though later style floppy disks have a rigid case around an internal floppy disk.

By the end of the 1980s, 5¼-inch disks had been superseded by 3½-inch disks. During this time, PCs frequently came equipped with drives of both sizes. By the mid-1990s, 5¼-inch drives had virtually disappeared, as the 3½-inch disk became the predominant floppy disk. The advantages of the 3½-inch disk were its higher capacity, its smaller physical size, and its rigid case which provided better protection from dirt and other environmental risks.

Prevalence

 

Imation USB floppy drive, model 01946: an external drive that accepts high-density disks

Floppy disks became commonplace during the 1980s and 1990s in their use with personal computers to distribute software, transfer data, and create backups. Before hard disks became affordable to the general population,^{[nb 1]} floppy disks were often used to store a computer's operating system (OS). Most home computers from that time have an elementary OS and BASIC stored in read-only memory (ROM), with the option of loading a more advanced OS from a floppy disk.

By the early 1990s, the increasing software size meant large packages like Windows or Adobe Photoshop required a dozen disks or more. In 1996, there were an estimated five billion standard floppy disks in use.^[11] Then, distribution of larger packages was gradually replaced by CD-ROMs, DVDs, and online distribution.

An attempt to enhance the existing 3½-inch designs was the SuperDisk in the late 1990s, using very narrow data tracks and a high precision head guidance mechanism with a capacity of 120 MB^[12] and backward-compatibility with standard 3½-inch floppies; a format war briefly occurred between SuperDisk and other high-density floppy-disk products, although ultimately recordable CDs/DVDs, solid-state flash storage, and eventually cloud-based online storage would render all these removable disk formats obsolete. External USB-based floppy disk drives are still available, and many modern systems provide firmware support for booting from such drives.

Gradual transition to other formats

 

Front and rear of a retail 3½-inch and 5¼-inch floppy disk cleaning kit, as sold in Australia at retailer Big W, circa early 1990s

In the mid-1990s, mechanically incompatible higher-density floppy disks were introduced, like the Iomega Zip disk. Adoption was limited by the competition between proprietary formats and the need to buy expensive drives for computers where the disks would be used. In some cases, failure in market penetration was exacerbated by the release of higher-capacity versions of the drive and media being not backward-compatible with the original drives, dividing the users between new and old adopters. Consumers were wary of making costly investments into unproven and rapidly changing technologies, so none of the technologies became the established standard.

Apple introduced the iMac G3 in 1998 with a CD-ROM drive but no floppy drive; this made USB-connected floppy drives popular accessories, as the iMac came without any writable removable media device.

Recordable CDs were touted as an alternative, because of the greater capacity, compatibility with existing CD-ROM drives, and—with the advent of re-writeable CDs and packet writing—a similar reusability as floppy disks. However, CD-R/RWs remained mostly an archival medium, not a medium for exchanging data or editing files on the medium itself, because there was no common standard for packet writing which allowed for small updates. Other formats, such as magneto-optical discs, had the flexibility of floppy disks combined with greater capacity, but remained niche due to costs. High-capacity backward compatible floppy technologies became popular for a while and were sold as an option or even included in standard PCs, but in the long run, their use was limited to professionals and enthusiasts.

Flash-based USB-thumb drives finally were a practical and popular replacement, that supported traditional file systems and all common usage scenarios of floppy disks. As opposed to other solutions, no new drive type or special software was required that impeded adoption, since all that was necessary was an already common USB port.

 

Different data storage media (Examples include: Flash drive, CD, tape drive, and CompactFlash)

Usage in the 21st century

 

A floppy hardware emulator, same size as a 3½-inch drive, provides a USB interface to the user.

By 2002, most manufacturers still provided floppy disk drives as standard equipment to meet user demand for file-transfer and an emergency boot device, as well as for the general secure feeling of having the familiar device.^[13] By this time, the retail cost of a floppy drive had fallen to around $20 (equivalent to $30 in 2021), so there was little financial incentive to omit the device from a system. Subsequently, enabled by the widespread support for USB flash drives and BIOS boot, manufacturers and retailers progressively reduced the availability of floppy disk drives as standard equipment. In February 2003, Dell, one of the leading personal computer vendors, announced that floppy drives would no longer be pre-installed on Dell Dimension home computers, although they were still available as a selectable option and purchasable as an aftermarket OEM add-on.^[14] By January 2007, only 2% of computers sold in stores contained built-in floppy disk drives.^[15]

Floppy disks are used for emergency boots in aging systems lacking support for other bootable media and for BIOS updates, since most BIOS and firmware programs can still be executed from bootable floppy disks. If BIOS updates fail or become corrupt, floppy drives can sometimes be used to perform a recovery. The music and theatre industries still use equipment requiring standard floppy disks (e.g. synthesizers, samplers, drum machines, sequencers, and lighting consoles). Industrial automation equipment such as programmable machinery and industrial robots may not have a USB interface; data and programs are then loaded from disks, damageable in industrial environments. This equipment may not be replaced due to cost or requirement for continuous availability; existing software emulation and virtualization do not solve this problem because a customized operating system is used that has no drivers for USB devices. Hardware floppy disk emulators can be made to interface floppy-disk controllers to a USB port that can be used for flash drives.

In May 2016, the United States Government Accountability Office released a report that covered the need to upgrade or replace legacy computer systems within federal agencies. According to this document, old IBM Series/1 minicomputers running on 8-inch floppy disks are still used to coordinate "the operational functions of the United States' nuclear forces". The government planned to update some of the technology by the end of the 2017 fiscal year.^[16][17]

Windows 10 and Windows 11 no longer comes with drivers for floppy disk drives (both internal and external). However, they will still support them with a separate device driver provided by Microsoft.^[18]

The British Airways Boeing 747-400 fleet, up to its retirement in 2020, used 3.5-inch floppy disks to load avionics software.^[19]

Some workstations in corporate computing environments still retained floppy disks while disabling USB ports, both moves done to restrict the amount of data that could be copied by unscrupulous employees.^{[dubious ]}

Sony, who had been in the floppy disk business since 1983, ended domestic sales of all six 3.5-inch floppy disk models as of March 2011.^[20] This has been viewed by some as the end of the floppy disk.^[21] While production of new floppy disk media has ceased,^[22] sales and uses of this media from inventories is expected to continue until at least 2026.^[23]

Legacy

 

Screenshot depicting a floppy disk as "save" icon

For more than two decades, the floppy disk was the primary external writable storage device used. Most computing environments before the 1990s were non-networked, and floppy disks were the primary means to transfer data between computers, a method known informally as sneakernet. Unlike hard disks, floppy disks are handled and seen; even a novice user can identify a floppy disk. Because of these factors, a picture of a 3½-inch floppy disk became an interface metaphor for saving data. The floppy disk symbol is still used by software on user-interface elements related to saving files (such as Microsoft Office 2021) even though physical floppy disks are largely obsolete.^[24]

Design

Structure

8-inch and 5¼-inch disks

 

Inside an 8-inch floppy disk

 

Disk notcher converts single-sided 5¼-inch diskettes to double-sided.

The 8-inch and 5¼-inch floppy disks contain a magnetically coated round plastic medium with a large circular hole in the center for a drive's spindle. The medium is contained in a square plastic cover that has a small oblong opening in both sides to allow the drive's heads to read and write data and a large hole in the center to allow the magnetic medium to spin by rotating it from its middle hole.

Inside the cover are two layers of fabric with the magnetic medium sandwiched in the middle. The fabric is designed to reduce friction between the medium and the outer cover, and catch particles of debris abraded off the disk to keep them from accumulating on the heads. The cover is usually a one-part sheet, double-folded with flaps glued or spot-welded together.

A small notch on the side of the disk identifies that it is writable, detected by a mechanical switch or phototransistor above it; if it is not present, the disk can be written; in the 8-inch disk the notch is covered to enable writing while in the 5¼-inch disk the notch is open to enable writing. Tape may be used over the notch to change the mode of the disk. Punch devices were sold to convert read-only disks to writable ones and enable writing on the unused side of single sided disks; such modified disks became known as flippy disks.

Another LED/photo-transistor pair located near the center of the disk detects the index hole once per rotation in the magnetic disk; it is used to detect the angular start of each track and whether or not the disk is rotating at the correct speed. Early 8‑inch and 5¼‑inch disks had physical holes for each sector and were termed hard sectored disks. Later soft-sectored disks have only one index hole, and sector position is determined by the disk controller or low-level software from patterns marking the start of a sector. Generally, the same drives are used to read and write both types of disks, with only the disks and controllers differing. Some operating systems using soft sectors, such as Apple DOS, do not use the index hole, and the drives designed for such systems often lack the corresponding sensor; this was mainly a hardware cost-saving measure.^[25]

3½-inch disk

 

Rear side of a 3½-inch floppy disk in a transparent case, showing its internal parts

The core of the 3½-inch disk is the same as the other two disks, but the front has only a label and a small opening for reading and writing data, protected by the shutter—a spring-loaded metal or plastic cover, pushed to the side on entry into the drive. Rather than having a hole in the center, it has a metal hub which mates to the spindle of the drive. Typical 3½-inch disk magnetic coating materials are:^[26]

• DD: 2 μm magnetic iron oxide
• HD: 1.2 μm cobalt-doped iron oxide
• ED: 3 μm barium ferrite

Two holes at the bottom left and right indicate whether the disk is write-protected and whether it is high-density; these holes are spaced as far apart as the holes in punched A4 paper, allowing write-protected high-density floppies to be clipped into standard ring binders. The dimensions of the disk shell are not quite square: its width is slightly less than its depth, so that it is impossible to insert the disk into a drive slot sideways (i.e. rotated 90 degrees from the correct shutter-first orientation). A diagonal notch at top right ensures that the disk is inserted into the drive in the correct orientation—not upside down or label-end first—and an arrow at top left indicates direction of insertion. The drive usually has a button that, when pressed, ejects the disk with varying degrees of force, the discrepancy due to the ejection force provided by the spring of the shutter. In IBM PC compatibles, Commodores, Apple II/IIIs, and other non-Apple-Macintosh machines with standard floppy disk drives, a disk may be ejected manually at any time. The drive has a disk-change switch that detects when a disk is ejected or inserted. Failure of this mechanical switch is a common source of disk corruption if a disk is changed and the drive (and hence the operating system) fails to notice.

One of the chief usability problems of the floppy disk is its vulnerability; even inside a closed plastic housing, the disk medium is highly sensitive to dust, condensation and temperature extremes. As with all magnetic storage, it is vulnerable to magnetic fields. Blank disks have been distributed with an extensive set of warnings, cautioning the user not to expose it to dangerous conditions. Rough treatment or removing the disk from the drive while the magnetic media is still spinning is likely to cause damage to the disk, drive head, or stored data. On the other hand, the 3½‑inch floppy has been lauded for its mechanical usability by human–computer interaction expert Donald Norman:^[27]

A simple example of a good design is the 3½-inch magnetic diskette for computers, a small circle of floppy magnetic material encased in hard plastic. Earlier types of floppy disks did not have this plastic case, which protects the magnetic material from abuse and damage. A sliding metal cover protects the delicate magnetic surface when the diskette is not in use and automatically opens when the diskette is inserted into the computer. The diskette has a square shape: there are apparently eight possible ways to insert it into the machine, only one of which is correct. What happens if I do it wrong? I try inserting the disk sideways. Ah, the designer thought of that. A little study shows that the case really isn't square: it's rectangular, so you can't insert a longer side. I try backward. The diskette goes in only part of the way. Small protrusions, indentations, and cutouts prevent the diskette from being inserted backward or upside down: of the eight ways one might try to insert the diskette, only one is correct, and only that one will fit. An excellent design.

 

The spindle motor from a 3½‑inch unit

 

A read-write head from a 3½‑inch unit

Operation

 

How the read-write head is applied on the floppy

 

Visualization of magnetic information on floppy disk (image recorded with CMOS-MagView)

A spindle motor in the drive rotates the magnetic medium at a certain speed, while a stepper motor-operated mechanism moves the magnetic read/write heads radially along the surface of the disk. Both read and write operations require the media to be rotating and the head to contact the disk media, an action originally accomplished by a disk-load solenoid.^[28] Later drives held the heads out of contact until a front-panel lever was rotated (5¼-inch) or disk insertion was complete (3½-inch). To write data, current is sent through a coil in the head as the media rotates. The head's magnetic field aligns the magnetization of the particles directly below the head on the media. When the current is reversed the magnetization aligns in the opposite direction, encoding one bit of data. To read data, the magnetization of the particles in the media induce a tiny voltage in the head coil as they pass under it. This small signal is amplified and sent to the floppy disk controller, which converts the streams of pulses from the media into data, checks it for errors, and sends it to the host computer system.

Formatting

Main article: Disk formatting

A blank unformatted diskette has a coating of magnetic oxide with no magnetic order to the particles. During formatting, the magnetizations of the particles are aligned forming tracks, each broken up into sectors, enabling the controller to properly read and write data. The tracks are concentric rings around the center, with spaces between tracks where no data is written; gaps with padding bytes are provided between the sectors and at the end of the track to allow for slight speed variations in the disk drive, and to permit better interoperability with disk drives connected to other similar systems.

Each sector of data has a header that identifies the sector location on the disk. A cyclic redundancy check (CRC) is written into the sector headers and at the end of the user data so that the disk controller can detect potential errors.

Some errors are soft and can be resolved by automatically re-trying the read operation; other errors are permanent and the disk controller will signal a failure to the operating system if multiple attempts to read the data still fail.

Insertion and ejection

After a disk is inserted, a catch or lever at the front of the drive is manually lowered to prevent the disk from accidentally emerging, engage the spindle clamping hub, and in two-sided drives, engage the second read/write head with the media.

In some 5¼-inch drives, insertion of the disk compresses and locks an ejection spring which partially ejects the disk upon opening the catch or lever. This enables a smaller concave area for the thumb and fingers to grasp the disk during removal.

Newer 5¼-inch drives and all 3½-inch drives automatically engage the spindle and heads when a disk is inserted, doing the opposite with the press of the eject button.

On Apple Macintosh computers with built-in 3½-inch disk drives, the ejection button is replaced by software controlling an ejection motor which only does so when the operating system no longer needs to access the drive. The user could drag the image of the floppy drive to the trash can on the desktop to eject the disk. In the case of a power failure or drive malfunction, a loaded disk can be removed manually by inserting a straightened paper clip into a small hole at the drive's front panel, just as one would do with a CD-ROM drive in a similar situation. The Sharp X68000 featured soft-eject 5¼-inch drives. Some late-generation IBM PS/2 machines had soft-eject 3½-inch disk drives as well for which some issues of DOS (i.e. PC DOS 5.02 and higher) offered an EJECT command.

Finding track zero

Before a disk can be accessed, the drive needs to synchronize its head position with the disk tracks. In some drives, this is accomplished with a Track Zero Sensor, while for others it involves the drive head striking an immobile reference surface.

In either case, the head is moved so that it is approaching track zero position of the disk. When a drive with the sensor has reached track zero, the head stops moving immediately and is correctly aligned. For a drive without the sensor, the mechanism attempts to move the head the maximum possible number of positions needed to reach track zero, knowing that once this motion is complete, the head will be positioned over track zero.

Some drive mechanisms such as the Apple II 5¼-inch drive without a track zero sensor, produce characteristic mechanical noises when trying to move the heads past the reference surface. This physical striking is responsible for the 5¼-inch drive clicking during the boot of an Apple II, and the loud rattles of its DOS and ProDOS when disk errors occurred and track zero synchronization was attempted.

Finding sectors

All 8-inch and some 5¼-inch drives used a mechanical method to locate sectors, known as either hard sectors or soft sectors, and is the purpose of the small hole in the jacket, off to the side of the spindle hole. A light beam sensor detects when a punched hole in the disk is visible through the hole in the jacket.

For a soft-sectored disk, there is only a single hole, which is used to locate the first sector of each track. Clock timing is then used to find the other sectors behind it, which requires precise speed regulation of the drive motor.

For a hard-sectored disk, there are many holes, one for each sector row, plus an additional hole in a half-sector position, that is used to indicate sector zero.

The Apple II computer system is notable in that it did not have an index hole sensor and ignored the presence of hard or soft sectoring. Instead, it used special repeating data synchronization patterns written to the disk between each sector, to assist the computer in finding and synchronizing with the data in each track.

The later 3½-inch drives of the mid-1980s did not use sector index holes, but instead also used synchronization patterns.

Most 3½-inch drives used a constant speed drive motor and contain the same number of sectors across all tracks. This is sometimes referred to as Constant Angular Velocity (CAV). In order to fit more data onto a disk, some 3½-inch drives (notably the Macintosh External 400K and 800K drives) instead use Constant Linear Velocity (CLV), which uses a variable speed drive motor that spins more slowly as the head moves away from the center of the disk, maintaining the same speed of the head(s) relative to the surface(s) of the disk. This allows more sectors to be written to the longer middle and outer tracks as the track length increases.

Sizes

Main articles: Floppy disk format and List of floppy disk formats

While the original IBM 8-inch disk was actually so defined, the other sizes are defined in the metric system, their usual names being but rough approximations.^[29]

Different sizes of floppy disks are mechanically incompatible, and disks can fit only one size of drive. Drive assemblies with both 3+1⁄2-inch and 5+1⁄4-inch slots were available during the transition period between the sizes, but they contained two separate drive mechanisms. In addition, there are many subtle, usually software-driven incompatibilities between the two. 5+1⁄4-inch disks formatted for use with Apple II computers would be unreadable and treated as unformatted on a Commodore. As computer platforms began to form, attempts were made at interchangeability. For example, the "SuperDrive" included from the Macintosh SE to the Power Macintosh G3 could read, write and format IBM PC format 3+1⁄2-inch disks, but few IBM-compatible computers had drives that did the reverse. 8-inch, 5+1⁄4-inch and 3+1⁄2-inch drives were manufactured in a variety of sizes, most to fit standardized drive bays. Alongside the common disk sizes were non-classical sizes for specialized systems.

8-inch floppy disk

 

8-inch floppy disk

Floppy disks of the first standard are 8 inches in diameter,^[1] protected by a flexible plastic jacket. It was a read-only device used by IBM as a way of loading microcode.^[30] Read/write floppy disks and their drives became available in 1972, but it was IBM's 1973 introduction of the 3740 data entry system^[31] that began the establishment of floppy disks, called by IBM the Diskette 1, as an industry standard for information interchange. Formatted diskette for this system store 242,944 bytes.^[32] Early microcomputers used for engineering, business, or word processing often used one or more 8-inch disk drives for removable storage; the CP/M operating system was developed for microcomputers with 8-inch drives.

The family of 8-inch disks and drives increased over time and later versions could store up to 1.2 MB;^[33] many microcomputer applications did not need that much capacity on one disk, so a smaller size disk with lower-cost media and drives was feasible. The 5+1⁄4-inch drive succeeded the 8-inch size in many applications, and developed to about the same storage capacity as the original 8-inch size, using higher-density media and recording techniques.

5.25-inch floppy disk

 

5¼-inch floppies, front and back

 

Uncovered 5+1⁄4‑inch disk mechanism with disk inserted.

The head gap of an 80‑track high-density (1.2 MB in the MFM format) 5+1⁄4‑inch drive (a.k.a. Mini diskette, Mini disk, or Minifloppy) is smaller than that of a 40‑track double-density (360 KB if double-sided) drive but can also format, read and write 40‑track disks provided the controller supports double stepping or has a switch to do so. 5+1⁄4-inch 80-track drives were also called hyper drives.^{[nb 2]} A blank 40‑track disk formatted and written on an 80‑track drive can be taken to its native drive without problems, and a disk formatted on a 40‑track drive can be used on an 80‑track drive. Disks written on a 40‑track drive and then updated on an 80 track drive become unreadable on any 40‑track drives due to track width incompatibility.

Single-sided disks were coated on both sides, despite the availability of more expensive double sided disks. The reason usually given for the higher price was that double sided disks were certified error-free on both sides of the media. Double-sided disks could be used in some drives for single-sided disks, as long as an index signal was not needed. This was done one side at a time, by turning them over (flippy disks); more expensive dual-head drives which could read both sides without turning over were later produced, and eventually became used universally.

3.5-inch floppy disk

 

Internal parts of a 3+1⁄2-inch floppy disk.

1. A hole that indicates a high-capacity disk.
2. The hub that engages with the drive motor.
3. A shutter that protects the surface when removed from the drive.
4. The plastic housing.
5. A polyester sheet reducing friction against the disk media as it rotates within the housing.
6. The magnetic coated plastic disk.
7. A schematic representation of one sector of data on the disk; the tracks and sectors are not visible on actual disks.
8. The write protection tab (unlabeled) in upper left.

 

A 3+1⁄2-inch floppy disk drive

In the early 1980s, many manufacturers introduced smaller floppy drives and media in various formats. A consortium of 21 companies eventually settled on a 3+1⁄2-inch design known as the Micro diskette, Micro disk, or Micro floppy, similar to a Sony design but improved to support both single-sided and double-sided media, with formatted capacities generally of 360 KB and 720 KB respectively. Single-sided drives shipped in 1983,^[34] and double-sided in 1984. The double-sided, high-density 1.44 MB (actually 1440 KiB = 1.41 MiB) disk drive, which would become the most popular, first shipped in 1986.^[35] The first Macintosh computers used single-sided 3+1⁄2-inch floppy disks, but with 400 KB formatted capacity. These were followed in 1986 by double-sided 800 KB floppies. The higher capacity was achieved at the same recording density by varying the disk-rotation speed with head position so that the linear speed of the disk was closer to constant. Later Macs could also read and write 1.44 MB HD disks in PC format with fixed rotation speed. Higher capacities were similarly achieved by Acorn's RISC OS (800 KB for DD, 1,600 KB for HD) and AmigaOS (880 KB for DD, 1,760 KB for HD).

All 3+1⁄2-inch disks have a rectangular hole in one corner which, if obstructed, write-enables the disk. A sliding detented piece can be moved to block or reveal the part of the rectangular hole that is sensed by the drive. The HD 1.44 MB disks have a second, unobstructed hole in the opposite corner that identifies them as being of that capacity.

In IBM-compatible PCs, the three densities of 3+1⁄2-inch floppy disks are backwards-compatible; higher-density drives can read, write and format lower-density media. It is also possible to format a disk at a lower density than that for which it was intended, but only if the disk is first thoroughly demagnetized with a bulk eraser, as the high-density format is magnetically stronger and will prevent the disk from working in lower-density modes.

Writing at different densities than those at which disks were intended, sometimes by altering or drilling holes, was possible but not supported by manufacturers. A hole on one side of a 3+1⁄2-inch disk can be altered as to make some disk drives and operating systems treat the disk as one of higher or lower density, for bidirectional compatibility or economical reasons.^{[clarification needed][36][37]} Some computers, such as the PS/2 and Acorn Archimedes, ignored these holes altogether.^[38]

Other sizes

Main article: Floppy disk variants

Other smaller floppy sizes were proposed, especially for portable or pocket-sized devices that needed a smaller storage device.

• 3¼-inch floppies otherwise similar to 5¼-inch floppies were proposed by Tabor and Dysan.
• Three-inch disks similar in construction to 3½-inch were manufactured and used for a time, particularly by Amstrad computers and word processors.
• A two-inch nominal size known as the Video Floppy was introduced by Sony for use with its Mavica still video camera.^[39]
• An incompatible two-inch floppy produced by Fujifilm called the LT-1 was used in the Zenith Minisport portable computer.^[40]

None of these sizes achieved much market success.^[41]

Sizes, performance and capacity

Main article: List of floppy disk formats

Floppy disk size is often referred to in inches, even in countries using metric and though the size is defined in metric. The ANSI specification of 3+1⁄2-inch disks is entitled in part "90 mm (3.5-inch)" though 90 mm is closer to 3.54 inches.^[42] Formatted capacities are generally set in terms of kilobytes and megabytes.

Historical sequence of floppy disk formats
In quantities of bits (b) or bytes (B) the prefixes:
k == 1,000 and K == 1,024
M has varying amounts.

Disk format	Year introduced	Formatted storage capacity	Marketed capacity
8-inch: IBM 23FD (read-only)	1971	81.664 kB^[43]	not marketed commercially
8-inch: Memorex 650	1972	175 kB^[44]	1.5 megabit full track^[44]
8-inch: SS SD IBM 33FD / Shugart 901	1973	242.844 kB^[43]	3.1 megabit unformatted
8-inch: DS SD IBM 43FD / Shugart 850	1976	568.320 kB^[43]	6.2 megabit unformatted
5+1⁄4-inch (35 track) Shugart SA 400	1976^[45]	87.5 KB^[46]	110 kB
8-inch DS DD IBM 53FD / Shugart 850	1977	962–1,184 KB depending upon sector size	1.2 MB
5+1⁄4-inch DD	1978	360 or 800 KB	360 KB
5+1⁄4-inch Apple Disk II (Pre-DOS 3.3)	1978	113.75 KB (256 byte sectors, 13 sectors/track, 35 tracks)	113 KB
5+1⁄4-inch Atari DOS 2.0S	1979	90 KB (128 byte sectors, 18 sectors/track, 40 tracks)	90 KB
5+1⁄4-inch Commodore DOS 1.0 (SSDD)	1979^[47]	172.5 KB^[48]	170 KB
5+1⁄4-inch Commodore DOS 2.1 (SSDD)	1980^[49]	170.75 KB^[48]	170 KB
5+1⁄4-inch Apple Disk II (DOS 3.3)	1980	140 KB (256 byte sectors, 16 sectors/track, 35 tracks)	140 KB
5+1⁄4-inch Apple Disk II (Roland Gustafsson's RWTS18)	1988	157.5 KB (768 byte sectors, 6 sectors/track, 35 tracks)	Game publishers privately contracted 3rd party custom DOS.
5+1⁄4-inch Victor 9000 / ACT Sirius 1 (SSDD)	1982^[50]	612 KB (512 byte sectors, 11-19 variable sectors / track, 80 tracks)	600 KB
5+1⁄4-inch Victor 9000 / ACT Sirius 1 (DSDD)	1982^[50]	1,196 KB (512 byte sectors, 11-19 variable sectors / track, 80 tracks)	1,200 KB
3+1⁄2-inch HP SS	1982	280 KB (256 byte sectors, 16 sectors/track, 70 tracks)	264 KB
5+1⁄4-inch Atari DOS 3	1983	127 KB (128 byte sectors, 26 sectors/track, 40 tracks)	130 KB
3-inch	1982^[51]^[52]	?	125 KB (SS/SD), 500 KB (DS/DD)^[52]
3+1⁄2-inch SS DD (at release)	1983	360 KB (400 KB on Macintosh)	500 KB
3+1⁄2-inch DS DD	1983	720 KB (800 KB on Macintosh and RISC OS,^[53] 880 KB on Amiga)	1 MB
5+1⁄4-inch QD	1980^[54]	720 KB	720 KB
5+1⁄4-inch RX50 (SSQD)	circa 1982	—	400 KB
5+1⁄4-inch HD	1982^[55]	1,200 KB	1.2 MB
3-inch Mitsumi Quick Disk	1985	128 to 256 KB	?
3-inch Famicom Disk System (derived from Quick Disk)	1986	112 KB	128 KB^[56]
2-inch	1989	720 KB^[57]	?
2+1⁄2-inch Sharp CE-1600F,^[58] CE-140F (chassis: FDU-250, medium: CE-1650F)^[59]	1986^[58]^[59]^[60]	turnable diskette with 62,464 bytes per side (512 byte sectors, 8 sectors/track, 16 tracks, GCR (4/5) recording)^[58]^[59]	2× 64 KB (128 KB)^[58]^[59]
5+1⁄4-inch^[61] Perpendicular	1986^[60]	100 KB per inch^[60]	?
3+1⁄2-inch HD	1986^[62]	1,440 KB (1,760 KB on Amiga)	1.44 MB (2.0 MB unformatted)
3+1⁄2-inch HD	1987	1,600 KB on RISC OS^[53]	1.6 MB
3+1⁄2-inch ED	1987^[63]	2,880 KB (3,200 KB on Sinclair QL)	2.88 MB
3+1⁄2-inch Floptical (LS)	1991	20,385 KB	21 MB
3+1⁄2-inch SuperDisk (LS-120)	1996	120,375 KB	120 MB
3+1⁄2-inch SuperDisk (LS-240)	1997	240,750 KB	240 MB
3+1⁄2-inch HiFD	1998/99	?	150/200 MB
Abbreviations: SD = Single Density; DD = Double Density; QD = Quad Density; HD = High Density; ED = Extra-high Density;^[64]^[65]^[66]^[67]^[68]LS = Laser Servo; HiFD = High capacity Floppy Disk; SS = Single Sided; DS = Double Sided
Formatted storage capacity is total size of all sectors on the disk: For 8-inch see List of floppy disk formats#IBM 8-inch formats. Spare, hidden and otherwise reserved sectors are included in this number. For 5+1⁄4- and 3+1⁄2-inch capacities quoted are from subsystem or system vendor statements. Marketed capacity is the capacity, typically unformatted, by the original media OEM vendor or in the case of IBM media, the first OEM thereafter. Other formats may get more or less capacity from the same drives and disks.

 

Two boxes of about 80 floppy disks together with one USB memory stick. The stick is capable of holding over 130 times as much data as the two boxes of disks put together.

Data is generally written to floppy disks in sectors (angular blocks) and tracks (concentric rings at a constant radius). For example, the HD format of 3½-inch floppy disks uses 512 bytes per sector, 18 sectors per track, 80 tracks per side and two sides, for a total of 1,474,560 bytes per disk.^{[69][failed verification]} Some disk controllers can vary these parameters at the user's request, increasing storage on the disk, although they may not be able to be read on machines with other controllers. For example, Microsoft applications were often distributed on 3+1⁄2-inch 1.68 MB DMF disks formatted with 21 sectors instead of 18; they could still be recognized by a standard controller. On the IBM PC, MSX and most other microcomputer platforms, disks were written using a constant angular velocity (CAV) format,^[63] with the disk spinning at a constant speed and the sectors holding the same amount of information on each track regardless of radial location.

Because the sectors have constant angular size, the 512 bytes in each sector are compressed more near the disk's center. A more space-efficient technique would be to increase the number of sectors per track toward the outer edge of the disk, from 18 to 30 for instance, thereby keeping nearly constant the amount of physical disk space used for storing each sector; an example is zone bit recording. Apple implemented this in early Macintosh computers by spinning the disk more slowly when the head was at the edge, while maintaining the data rate, allowing 400 KB of storage per side and an extra 80 KB on a double-sided disk.^[70] This higher capacity came with a disadvantage: the format used a unique drive mechanism and control circuitry, meaning that Mac disks could not be read on other computers. Apple eventually reverted to constant angular velocity on HD floppy disks with their later machines, still unique to Apple as they supported the older variable-speed formats.

Disk formatting is usually done by a utility program supplied by the computer OS manufacturer; generally, it sets up a file storage directory system on the disk, and initializes its sectors and tracks. Areas of the disk unusable for storage due to flaws can be locked (marked as "bad sectors") so that the operating system does not attempt to use them. This was time-consuming so many environments had quick formatting which skipped the error checking process. When floppy disks were often used, disks pre-formatted for popular computers were sold. The unformatted capacity of a floppy disk does not include the sector and track headings of a formatted disk; the difference in storage between them depends on the drive's application. Floppy disk drive and media manufacturers specify the unformatted capacity (for example, 2 MB for a standard 3+1⁄2-inch HD floppy). It is implied that this should not be exceeded, since doing so will most likely result in performance problems. DMF was introduced permitting 1.68 MB to fit onto an otherwise standard 3+1⁄2-inch disk; utilities then appeared allowing disks to be formatted as such.

Mixtures of decimal prefixes and binary sector sizes require care to properly calculate total capacity. Whereas semiconductor memory naturally favors powers of two (size doubles each time an address pin is added to the integrated circuit), the capacity of a disk drive is the product of sector size, sectors per track, tracks per side and sides (which in hard disk drives with multiple platters can be greater than 2). Although other sector sizes have been known in the past, formatted sector sizes are now almost always set to powers of two (256 bytes, 512 bytes, etc.), and, in some cases, disk capacity is calculated as multiples of the sector size rather than only in bytes, leading to a combination of decimal multiples of sectors and binary sector sizes. For example, 1.44 MB 3+1⁄2-inch HD disks have the "M" prefix peculiar to their context, coming from their capacity of 2,880 512-byte sectors (1,440 KiB), consistent with neither a decimal megabyte nor a binary mebibyte (MiB). Hence, these disks hold 1.47 MB or 1.41 MiB. Usable data capacity is a function of the disk format used, which in turn is determined by the FDD controller and its settings. Differences between such formats can result in capacities ranging from approximately 1,300 to 1,760 KiB (1.80 MB) on a standard 3+1⁄2-inch high-density floppy (and up to nearly 2 MB with utilities such as 2M/2MGUI). The highest capacity techniques require much tighter matching of drive head geometry between drives, something not always possible and unreliable. For example, the LS-240 drive supports a 32 MB capacity on standard 3+1⁄2-inch HD disks,^[71] but this is a write-once technique, and requires its own drive.

The raw maximum transfer rate of 3+1⁄2-inch ED floppy drives (2.88 MB) is nominally 1,000 kilobits/s, or approximately 83% that of single-speed CD‑ROM (71% of audio CD). This represents the speed of raw data bits moving under the read head; however, the effective speed is somewhat less due to space used for headers, gaps and other format fields and can be even further reduced by delays to seek between tracks.

See also

•  Physics portal
•  Electronics portal

• Berg connector for 3½-inch floppy drive
• dd (Unix)
• Disk image
• Don't Copy That Floppy
• Floppy disk controller
• Floppy disk hardware emulator
• Floppy disk variants
• Hard disk drive
• History of the floppy disk
• List of floppy disk formats
• Shugart bus – popular mainly for 8-inch drives, and partially for 5¼-inch
• XDF
• VGA-Copy copy tool (retries on errors, over-formatted floppies), DOS, discontinued
• Zip drive

Notes

1. The cost of a hard disk with a controller in the mid 1980s was thousands of dollars, for capacity of 80 MB or less.
2. "Hyper drive" was an alternative name for 5¼-inch 80-track HD floppy drives with 1.2 MB capacity. The term was used f.e. by Philips Austria for their Philips :YES and Digital Research in conjunction with DOS Plus.

References

1. Teja, Edward R. (1985). The Designer's Guide to Disk Drives (1st ed.). Reston, Virginia, USA: Reston / Prentice hall. ISBN 0-8359-1268-X.
2. Fletcher, Richard (30 January 2007). "PC World Announces the End of the Floppy Disk". The Daily Telegraph. from the original on 2 January 2012. Retrieved 2 August 2020.
3. "1971: Floppy disk loads mainframe computer data". Computer History Museum. Computer History Museum. from the original on 8 December 2015. Retrieved 1 December 2015.
4. . Archived from the original on 26 July 2011. Retrieved 15 October 2012.
5. IBM's 370/145 Uncovered; Interesting Curves Revealed, Datamation, November 1, 1970
6. Watson (24 May 2010). "The Floppy Disk". Canadian Business. Vol. 83, no. 8. p. 17.
7. Porter, James (November 1992). 1992 Disk/Trend Report - Flexible Disk Drives (Report). p. DT14-3.
8. "The Microfloppy—One Key to Portability", Thomas R. Jarrett, Computer Technology Review, winter 1983 (Jan 1984), pp. 245–7
9. Picture of disk
10. 1991 Disk/Trend Report, Flexible Disk Drives, Figure 2
11. Reinhardt, Andy (12 August 1996). . Business Week. No. 33. The McGraw-Hill Companies. ISSN 0007-7135. Archived from the original on 6 July 2008.
12. . LinuxCommand.org. 4 January 2006. Archived from the original on 27 July 2011. Retrieved 22 June 2011.
13. Spring, Tom (24 July 2002). . PC World. Archived from the original on 24 December 2011. Retrieved 4 April 2012.
14. "R.I.P. Floppy Disk". BBC News. 1 April 2003. from the original on 16 February 2009. Retrieved 19 July 2011.
15. Derbyshire, David (30 January 2007). "Floppy disks ejected as demand slumps". The Daily Telegraph. from the original on 22 May 2011. Retrieved 19 July 2011.
16. "Federal Agencies Need to Address Aging Legacy Systems" (PDF). Report to Congressional Requesters. United States Government Accountability Office. May 2016. (PDF) from the original on 2 June 2016. Retrieved 26 May 2016.
17. Trujillo, Mario (25 May 2016). "US nuclear emergency messaging system still uses floppy disks". The Hill. from the original on 29 May 2016. Retrieved 30 May 2016.
18. "How to use Floppy Disk on Windows 10". 9 March 2016. from the original on 17 November 2018. Retrieved 11 June 2019.
19. Warren, Tom (11 August 2020). "Boeing 747s still get critical updates via floppy disks: A rare look inside a 20-year-old airliner". The Verge. Vox Media. Retrieved 26 February 2021.
20. "Notice of Termination of Sales of 3.5-inch Floppy Disks". 23 April 2010. Retrieved 14 September 2022.
21. SORREL, CHARLIE (26 April 2010). "Sony Announces the Death of the Floppy Disk". Wired. Retrieved 14 September 2022.
22. Robinson, Dan (20 September 2022). "'Last man standing in the floppy disk business' reckons his company has 4 years left". The Register. Retrieved 23 September 2022.
23. Hilkmann, Niek; Walskaar, Thomas (12 September 2022). "We Spoke With the Last Person Standing in the Floppy Disk Business". Retrieved 14 September 2022. Turns out the obsolete floppy is way more in demand than you'd think. ... I expect to be in this business for at least another four years.
24. Landphair, Ted (10 March 2007). . VOA News. Voice of America. Archived from the original on 10 October 2016. Retrieved 25 December 2008.
25. . Apple II History. 2 December 2008. Archived from the original on 19 February 2018. Retrieved 17 February 2018. Wozniak's technique would allow the drive to do self-synchronization ("soft sectoring"), not have to deal with that little timing hole, and save on hardware.
26. (M)Tronics SCS (20 May 2007). [Floppy disk drives] (in German). Archived from the original on 19 June 2017. Retrieved 19 June 2017.
27. Norman, Donald (1990). "Chapter 1". The Design of Everyday Things. New York, USA: Doubleday. ISBN 0-385-26774-6.
28. Porter, Jim, ed. (2005). (PDF). p. 4. Archived from the original (PDF) on 13 May 2015. Retrieved 22 June 2011.
29. X3.162, ANSI, 1994, Information Systems – Unformatted Flexible Disk Cartridge for Information Interchange, 5.25 in (130 mm), 96 Tracks per inch (3.8 Tracks per Millimeter), General, Physical, and Magnetic Requirements (includes ANSI X3.162/TC-1-1995) Specifies the general, physical, and magnetic requirements for interchangeability for the two-sided, 5.25 in (130 mm) flexible disk cartridge
30. . Louisiana State University. Archived from the original on 18 October 2014. Retrieved 2 December 2013.
31. "3740". Archives. IBM. 23 January 2003. from the original on 25 December 2017. Retrieved 13 October 2014.
32. IBM 3740 Data Entry System System Summary and Installation Manual – Physical Planning (PDF). IBM. 1974. p. 2. (PDF) from the original on 15 February 2017. Retrieved 7 March 2019 – via Stuttgart University. The diskette is about 8" (20 cm) square and has a net capacity of 1898 128-character records – about one day's data entry activity. Each of the diskette's 73 magnetic recording tracks available for data entry can hold 26 sectors of up to 128 characters each.
33. "The IBM Diskette General Information Manual". DE: Z80. from the original on 28 October 2014. Retrieved 13 October 2014.
34. Shea, Tom (13 June 1983). "Shrinking drives increase storage". InfoWorld. pp. 1, 7, 8, 9, 11. Shugart is one of the major subscribers to the 3¹⁄₂-inch micro-floppy standard, along with Sony and 20 other company ... Its single-sided SA300 micro-floppy drive offers 500K of unformatted storage. Shugart's Kevin Burr said the obvious next step is to put another 500K of storage on the other side of the diskette and that the firm will come out with a double-sided 1-megabyte micro-floppy drive soon.
35. 1986 Disk/Trend Report – Flexible Disk Drives. Disk/Trend, Inc. November 1986. p. FSPEC-59. Reports Sony shipped in 1Q 1986
36. "Managing Disks". from the original on 24 May 2006. Retrieved 25 May 2006.
37. "A question of floppies". from the original on 1 October 2011. Retrieved 20 February 2011.
38. "Formatting 720K Disks on a 1.44MB Floppy". Floppy Drive. from the original on 23 July 2011. Retrieved 11 February 2011.
39. "Sony / Canon 2 Inch Video Floppy". Museum of Obsolete Media. 2 May 2013. from the original on 13 January 2018. Retrieved 4 January 2018.
40. "2 inch lt1 floppy disk". Museum of Obsolete Media. 22 July 2017. from the original on 4 January 2018. Retrieved 4 January 2018.
41. Disk/Trend Report-Flexible Disk Drives, Disk/Trend Inc., November 1991, pp. SUM-27
42. ANSI X3.137, One- and Two-Sided, Unformatted, 90-mm (3.5-inch) 5,3-tpmm (135-tpi), Flexible Disk Cartridge for 7958 bpr Use. General, Physical and Magnetic Requirements.
43. Engh, James T. (September 1981). "The IBM Diskette and Diskette Drive". IBM Journal of Research and Development. 25 (5): 701–710. doi:10.1147/rd.255.0701.
44. (PDF). Archived from the original (PDF) on 25 July 2011. Retrieved 22 June 2011.
45. Sollman, George (July 1978). "Evolution of the Minifloppy Product Family". IEEE Transactions on Magnetics. 14 (4): 160–66. doi:10.1109/TMAG.1978.1059748. ISSN 0018-9464. S2CID 32505773.
46. . Swtpc. 25 June 2007. Archived from the original on 27 May 2014. Retrieved 22 June 2011.
47. Beals, Gene (n.d.). "New Commodore Products: A Quick Review" (PDF). PET User Notes. Vol. 2, no. 1. Montgomeryville, Pennsylvania. p. 2. (PDF) from the original on 11 June 2016. Retrieved 7 October 2018.
48. West, Raeto Collin (January 1982). Programming the PET/CBM: The Reference Encyclopedia For Commodore PET & CBM Users. COMPUTE! Books. p. 167. ISBN 0-942386-04-3. Retrieved 7 October 2018.
49. Commodore Business Machines (5 February 1980). "cbmsrc / DOS_4040 / dos". GitHub. Retrieved 7 October 2018. {{cite web}}: |author= has generic name (help)
50. "Victor 9000 Hardware Reference Manual" (PDF). (PDF) from the original on 29 January 2022. Retrieved 12 September 2022.
51. "Chronology of Events in the History of Microcomputers − 1981–1983 Business Takes Over". from the original on 7 December 2008. Retrieved 4 October 2008.
52. (PDF). Archived from the original (PDF) on 8 August 2012. Retrieved 4 October 2008.
53. "6. Using floppy and hard discs". RISC OS 3.7 User Guide. 21 January 1997. Retrieved 4 January 2022.^{[permanent dead link]}
54. Porter, James (December 1982). 1982 Disk/Trend Report – Flexible Disk Drives. Disk/Trend. p. DT13-3. The original 48 tpi drives were joined by 96tpi drives from Tandon, Micro Peripherals and Micropolis in 1980 ...
55. 1986 Disk/Trend Report, Flexible Disk Drives
56. "Revisiting the Famicom Disk System". Eurogamer. 27 July 2019.
57. "Viability of 2-Inch Media Standard for PCs in Doubt". InfoWorld. 11 (31): 21. 31 July 1989.
58. "Model CE-1600F" (PDF). Sharp PC-1600 Service Manual. Yamatokoriyama, Japan: Sharp Corporation, Information Systems Group, Quality & Reliability Control Center. July 1986. pp. 98–104. (PDF) from the original on 23 March 2017. Retrieved 12 March 2017.
59. Sharp Service Manual Model CE-140F Pocket Disk Drive (PDF). Sharp Corporation. 00ZCE140F/SME. (PDF) from the original on 11 March 2017. Retrieved 11 March 2017.
60. Bateman, Selby (March 1986). "The Future of Mass Storage". COMPUTE!. No. 70. COMPUTE! Publications, Inc. p. 18. from the original on 1 July 2018. Retrieved 7 October 2018.
61. JP S6344319A, Kitagami, Osamu & Fujiwara, Hideo, "Production of perpendicular magnetic recording medium", published 1988-02-25, assigned to Hitachi Maxell 
62. "Vendor Introduces Ultra High-Density Floppy Disk Media". InfoWorld. 8 (45): 19. 10 November 1986.
63. Mueller, Scott (2004). Upgrading and Repairing PCs, 15th Anniversary Edition. Que Publishing. p. 1380. ISBN 0-7897-2974-1. Retrieved 16 July 2011.
64. Mueller, Scott (1994). Hardware-Praxis – PCs warten reparieren, aufrüsten und konfigurieren (in German) (3rd ed.). Addison-Wesley Publishing Company. p. 441. ISBN 3-89319-705-2.
65. Inc, InfoWorld Media Group (14 October 1991). "InfoWorld". InfoWorld Media Group, Inc. – via Google Books. {{cite web}}: |last= has generic name (help)
66. Shah, Katen A. (1996) [September 1992, April 1992]. Intel 82077SL for Super-Dense Floppies (PDF) (Application Note) (2 ed.). Intel Corporation, IMD Marketing. AP-358, 292093-002. (PDF) from the original on 19 June 2017. Retrieved 19 June 2017.
67. Inc, Ziff Davis (10 September 1991). "PC Mag". Ziff Davis, Inc. – via Google Books. {{cite web}}: |last= has generic name (help)
68. Inc, InfoWorld Media Group (19 March 1990). "InfoWorld". InfoWorld Media Group, Inc. – via Google Books. {{cite web}}: |last= has generic name (help)
69. "Chapter 8: Floppy Disk Drives" (PDF). (PDF) from the original on 27 January 2012. Retrieved 16 July 2011.
70. "The Original Macintosh". Folklore. from the original on 5 December 2013. Retrieved 3 December 2013.
71. . Mt. San Antonio College. Archived from the original on 7 December 2013.

Further reading

• Weyhrich, Steven (2005). : A detailed essay describing one of the first commercial floppy disk drives (from the Apple II History website).
• Immers, Richard; Neufeld, Gerald G. (1984). Inside Commodore DOS: The Complete Guide to the 1541 Disk Operating System. Datamost & Reston Publishing Company (Prentice-Hall). ISBN 0-8359-3091-2.
• Englisch, Lothar; Szczepanowski, Norbert (1984). The Anatomy of the 1541 Disk Drive. Grand Rapids, Michigan, USA, Abacus Software (translated from the original 1983 German edition, Düsseldorf, Data Becker GmbH). ISBN 0-916439-01-1.
• Hewlett Packard: 9121D/S Disc Memory Operator's Manual; printed 1 September 1982; part number 09121-90000.

External links

 

Wikimedia Commons has media related to Diskette.

• HowStuffWorks: How Floppy Disk Drives Work
• Computer Hope: Information about computer floppy drives
• (mention of ANSI X3.162 and X3.171 floppy standards)
• Floppy disk drives and media technical information
• The Floppy User Guide -historical technical material
• Summary of Floppy Disk Types and Specifications