Common source

In electronics, a common-source amplifier is one of three basic single-stage field-effect transistor (FET) amplifier topologies, typically used as a voltage or transconductance amplifier. The easiest way to tell if a FET is common source, common drain, or common gate is to examine where the signal enters and leaves. The remaining terminal is what is known as "common". In this example, the signal enters the gate, and exits the drain. The only terminal remaining is the source. This is a common-source FET circuit. The analogous bipolar junction transistor circuit may be viewed as a transconductance amplifier or as a voltage amplifier. (See classification of amplifiers). As a transconductance amplifier, the input voltage is seen as modulating the current going to the load. As a voltage amplifier, input voltage modulates the current flowing through the FET, changing the voltage across the output resistance according to Ohm's law. However, the FET device's output resistance typically is not high enough for a reasonable transconductance amplifier (ideally infinite), nor low enough for a decent voltage amplifier (ideally zero). Another major drawback is the amplifier's limited high-frequency response. Therefore, in practice the output often is routed through either a voltage follower (common-drain or CD stage), or a current follower (common-gate or CG stage), to obtain more favorable output and frequency characteristics. The CS–CG combination is called a cascode amplifier.

Figure 1: Basic N-channel JFET common-source circuit (neglecting biasing details).

Figure 2: Basic N-channel JFET common-source circuit with source degeneration.

Characteristics

At low frequencies and using a simplified hybrid-pi model (where the output resistance due to channel length modulation is not considered), the following closed-loop small-signal characteristics can be derived.

	Definition	Expression
Current gain	${\displaystyle A_{\text{i}}\triangleq {\frac {i_{\text{out}}}{i_{\text{in}}}}\,}$	${\displaystyle \infty \,}$
Voltage gain	${\displaystyle A_{\text{v}}\triangleq {\frac {v_{\text{out}}}{v_{\text{in}}}}\,}$	${\displaystyle {\begin{matrix}-{\frac {g_{\mathrm {m} }R_{\text{D}}}{1+g_{\mathrm {m} }R_{\text{S}}}}\end{matrix}}\,}$
Input impedance	${\displaystyle r_{\text{in}}\triangleq {\frac {v_{\text{in}}}{i_{\text{in}}}}\,}$	${\displaystyle \infty \,}$
Output impedance	${\displaystyle r_{\text{out}}\triangleq {\frac {v_{\text{out}}}{i_{\text{out}}}}}$	${\displaystyle R_{\text{D}}\,}$

Bandwidth

 

Figure 3: Basic N-channel MOSFET common-source amplifier with active load I_D.

 

Figure 4: Small-signal circuit for N-channel MOSFET common-source amplifier.

 

Figure 5: Small-signal circuit for N-channel MOSFET common-source amplifier using Miller's theorem to introduce Miller capacitance C_M.

Bandwidth of common-source amplifier tends to be low, due to high capacitance resulting from the Miller effect. The gate-drain capacitance is effectively multiplied by the factor ${\displaystyle 1+|A_{\text{v}}|\,}$ , thus increasing the total input capacitance and lowering the overall bandwidth.

Figure 3 shows a MOSFET common-source amplifier with an active load. Figure 4 shows the corresponding small-signal circuit when a load resistor R_L is added at the output node and a Thévenin driver of applied voltage V_A and series resistance R_A is added at the input node. The limitation on bandwidth in this circuit stems from the coupling of parasitic transistor capacitance C_gd between gate and drain and the series resistance of the source R_A. (There are other parasitic capacitances, but they are neglected here as they have only a secondary effect on bandwidth.)

Using Miller's theorem, the circuit of Figure 4 is transformed to that of Figure 5, which shows the Miller capacitance C_M on the input side of the circuit. The size of C_M is decided by equating the current in the input circuit of Figure 5 through the Miller capacitance, say i_M, which is:

${\displaystyle \ i_{\mathrm {M} }=j\omega C_{\mathrm {M} }v_{\mathrm {GS} }=j\omega C_{\mathrm {M} }v_{\mathrm {G} }}$  ,

to the current drawn from the input by capacitor C_gd in Figure 4, namely jωC_gd v_GD. These two currents are the same, making the two circuits have the same input behavior, provided the Miller capacitance is given by:

${\displaystyle C_{\mathrm {M} }=C_{\mathrm {gd} }{\frac {v_{\mathrm {GD} }}{v_{\mathrm {GS} }}}=C_{\mathrm {gd} }\left(1-{\frac {v_{\mathrm {D} }}{v_{\mathrm {G} }}}\right)}$  .

Usually the frequency dependence of the gain v_D / v_G is unimportant for frequencies even somewhat above the corner frequency of the amplifier, which means a low-frequency hybrid-pi model is accurate for determining v_D / v_G. This evaluation is Miller's approximation^[1] and provides the estimate (just set the capacitances to zero in Figure 5):

${\displaystyle {\frac {v_{\mathrm {D} }}{v_{\mathrm {G} }}}\approx -g_{\mathrm {m} }(r_{\mathrm {O} }\parallel R_{\mathrm {L} })}$  ,

so the Miller capacitance is

${\displaystyle C_{\mathrm {M} }=C_{\mathrm {gd} }\left(1+g_{\mathrm {m} }(r_{\mathrm {O} }\parallel R_{\mathrm {L} })\right)}$  .

The gain g_m (r_O || R_L) is large for large R_L, so even a small parasitic capacitance C_gd can become a large influence in the frequency response of the amplifier, and many circuit tricks are used to counteract this effect. One trick is to add a common-gate (current-follower) stage to make a cascode circuit. The current-follower stage presents a load to the common-source stage that is very small, namely the input resistance of the current follower (R_L ≈ 1 / g_m ≈ V_ov / (2I_D) ; see common gate). Small R_L reduces C_M.^[2] The article on the common-emitter amplifier discusses other solutions to this problem.

Returning to Figure 5, the gate voltage is related to the input signal by voltage division as:

${\displaystyle v_{\mathrm {G} }=V_{\mathrm {A} }{\frac {1/(j\omega C_{\mathrm {M} })}{1/(j\omega C_{\mathrm {M} })+R_{\mathrm {A} }}}=V_{\mathrm {A} }{\frac {1}{1+j\omega C_{\mathrm {M} }R_{\mathrm {A} }}}}$  .

The bandwidth (also called the 3 dB frequency) is the frequency where the signal drops to 1/ √2 of its low-frequency value. (In decibels, dB(√2) = 3.01 dB). A reduction to 1/ √2 occurs when ωC_M R_A = 1, making the input signal at this value of ω (call this value ω_3 dB, say) v_G = V_A / (1+j). The magnitude of (1+j) = √2. As a result, the 3 dB frequency f_3 dB = ω_3 dB / (2π) is:

${\displaystyle f_{\mathrm {3dB} }={\frac {1}{2\pi R_{\mathrm {A} }C_{\mathrm {M} }}}={\frac {1}{2\pi R_{\mathrm {A} }[C_{\mathrm {gd} }(1+g_{\mathrm {m} }(r_{\mathrm {O} }\parallel R_{\mathrm {L} })]}}}$  .

If the parasitic gate-to-source capacitance C_gs is included in the analysis, it simply is parallel with C_M, so

${\displaystyle f_{\mathrm {3dB} }={\frac {1}{2\pi R_{\mathrm {A} }(C_{\mathrm {M} }+C_{\mathrm {gs} })}}={\frac {1}{2\pi R_{\mathrm {A} }[C_{\mathrm {gs} }+C_{\mathrm {gd} }(1+g_{\mathrm {m} }(r_{\mathrm {O} }\parallel R_{\mathrm {L} }))]}}}$  .

Notice that f_3 dB becomes large if the source resistance R_A is small, so the Miller amplification of the capacitance has little effect upon the bandwidth for small R_A. This observation suggests another circuit trick to increase bandwidth: add a common-drain (voltage-follower) stage between the driver and the common-source stage so the Thévenin resistance of the combined driver plus voltage follower is less than the R_A of the original driver.^[3]

Examination of the output side of the circuit in Figure 2 enables the frequency dependence of the gain v_D / v_G to be found, providing a check that the low-frequency evaluation of the Miller capacitance is adequate for frequencies f even larger than f_3 dB. (See article on pole splitting to see how the output side of the circuit is handled.)

See also

• Miller effect
• Pole splitting
• Common gate
• Common drain
• Common base
• Common emitter
• Common collector

References

1. R.R. Spencer; M.S. Ghausi (2003). Introduction to electronic circuit design. Upper Saddle River NJ: Prentice Hall/Pearson Education, Inc. p. 533. ISBN 0-201-36183-3.
2. Thomas H Lee (2004). The design of CMOS radio-frequency integrated circuits (Second ed.). Cambridge UK: Cambridge University Press. pp. 246–248. ISBN 0-521-83539-9.
3. Thomas H Lee (2004). pp. 251–252. ISBN 0-521-83539-9.

External links

• Common-Source Amplifier Stage