fbpx
Wikipedia

Ti-sapphire laser

January 01, 1970

The correct title of this article is Ti:sapphire laser. The substitution of the colon is due to technical restrictions.

Ti:sapphire lasers (also known as Ti:Al2O3 lasers, titanium-sapphire lasers, or Ti:sapphs) are tunable lasers which emit red and near-infrared light in the range from 650 to 1100 nanometers. These lasers are mainly used in scientific research because of their tunability and their ability to generate ultrashort pulses thanks to its broad light emission spectrum. Lasers based on Ti:sapphire were first constructed and invented in June 1982 by Peter Moulton at the MIT Lincoln Laboratory.[1]

Part of a Ti:sapphire oscillator. The Ti:sapphire crystal is the bright red light source on the left. The green light is from the pump diode

Titanium-sapphire refers to the lasing medium, a crystal of sapphire (Al2O3) that is doped with Ti3+ ions. A Ti:sapphire laser is usually pumped with another laser with a wavelength of 514 to 532 nm, for which argon-ion lasers (514.5 nm) and frequency-doubled Nd:YAG, Nd:YLF, and Nd:YVO lasers (527–532 nm) are used. They are capable of laser operation from 670 nm to 1,100 nm wavelength.[2] Ti:sapphire lasers operate most efficiently at wavelengths near 800 nm.[3]

Types edit

 
The inner optical setup of a femtosecond Ti-sapphire pulsed laser

Mode-locked oscillators edit

Mode-locked oscillators generate ultrashort pulses with a typical duration between a few picoseconds and 10 femtoseconds, in special cases even around 5 femtoseconds (few carrier wave cycles in each laser pulses). The pulse repetition frequency is in most cases around 70 to 90 MHz, as given by the oscillator's round-trip optical path, typically a few meters. Ti:sapphire oscillators are normally pumped with a continuous-wave laser beam from an argon or frequency-doubled Nd:YVO4 laser. Typically, such an oscillator has an average output power of 0.4 to 2.5 watts (5.7 to 35 nJ in each laser pulse for the 70 MHz repetition rate).

Chirped-pulse amplifiers edit

Main article: Chirped pulse amplification

These devices generate ultrashort, ultra-high-intensity pulses with a duration of 20 to 100 femtoseconds. A typical one stage amplifier can produce pulses of up to 5 millijoules in energy at a repetition frequency of 1000 hertz, while a larger, multistage facility can produce pulses up to several joules, with a repetition rate of up to 10 Hz. Usually, amplifier crystals are pumped with a pulsed frequency-doubled Nd:YLF laser at 527 nm and operate at 800 nm. Two different designs exist for the amplifier: regenerative amplifier and multi-pass amplifier.

Regenerative amplifiers operate by amplifying single pulses from an oscillator (see above). Instead of a normal cavity with a partially reflective mirror, they contain high-speed optical switches that insert a pulse into a cavity and take the pulse out of the cavity exactly at the right moment when it has been amplified to a high intensity.

The term 'chirped-pulse' refers to a special construction that is necessary to prevent the pulse from damaging the components in the laser. The pulse is stretched in time so that the energy is not all located at the same point in time and space. This prevents damage to the optics in the amplifier. Then the pulse is optically amplified and recompressed in time to form a short, localized pulse. All optics after this point should be chosen to take the high energy density into consideration.

In a multi-pass amplifier, there are no optical switches. Instead, mirrors guide the beam a fixed number of times (two or more) through the Ti:sapphire crystal with slightly different directions. A pulsed pump beam can also be multi-passed through the crystal, so that more and more passes pump the crystal. First the pump beam pumps a spot in the gain medium. Then the signal beam first passes through the center for maximal amplification, but in later passes the diameter is increased to stay below the damage-threshold, to avoid amplification the outer parts of the beam, thus increasing beam quality and cutting off some amplified spontaneous emission and to completely deplete the inversion in the gain medium.

 
A Ti:Sapphire crystal in the centre of a multipass amplifier Quantronix Odin is pumped by 5W green beam (faintly visible coming from right), amplifies femtosecond pulses that pass it several times under different angles (invisible on the photo) and loses part of energy as red fluorescence light

The pulses from chirped-pulse amplifiers are often converted to other wavelengths by means of various nonlinear optical processes.

At 5 mJ in 100 femtoseconds, the peak power of such a laser is 50 gigawatts.[4] When focused by a lens, these laser pulses will ionise any material placed in the focus, including air molecules, and lead to short filament propagation and strong nonlinear optics effects that generate a wide spectrum of wavelengths.

 
Femtosecond pulses generate multiple angle-resolved colour patterns when focused; note their fan-out angle is even higher than that of the focused laser beam

Tunable continuous wave lasers edit

Titanium-sapphire is especially suitable for pulsed lasers since an ultrashort pulse inherently contains a wide spectrum of frequency components. This is due to the inverse relationship between the frequency bandwidth of a pulse and its time duration, due to their being conjugate variables. However, with an appropriate design, titanium-sapphire can also be used in continuous wave lasers with extremely narrow linewidths tunable over a wide range.

History and applications edit

 
CW single-frequency ring Ti:Sapphire laser in operation at Novosibirsk State University

The Ti:sapphire laser was invented by Peter Moulton in June 1982 at MIT Lincoln Laboratory in its continuous wave version. Subsequently, these lasers were shown to generate ultrashort pulses through Kerr-lens modelocking.[5] Strickland and Mourou, in addition to others, working at the University of Rochester, showed chirped pulse amplification of this laser within a few years,[6] for which these two shared in the 2018 Nobel Prize in physics[7] (along with Arthur Ashkin for optical tweezers). The cumulative product sales of the Ti:sapphire laser has amounted to more than $600 million, making it a big commercial success that has sustained the solid state laser industry for more than three decades.[8][9]

The ultrashort pulses generated by Ti:sapphire lasers in the time domain corresponds to mode-locked optical frequency combs in the spectral domain. Both the temporal and spectral properties of these lasers make them highly desirable for frequency metrology, spectroscopy, or for pumping nonlinear optical processes. One half of the Nobel prize for physics in 2005 was awarded to the development of the optical frequency comb technique, which heavily relied on the Ti:sapphire laser and its self-modelocking properties.[10][11][12] The continuous wave versions of these lasers can be designed to have nearly quantum limited performance, resulting in a low noise and a narrow linewidth, making them attractive for quantum optics experiments.[13] The reduced amplified spontaneous emission noise in the radiation of Ti:sapphire lasers lends great strength in their application as optical lattices for the operation of state-of-the-art atomic clocks. Apart from fundamental science applications in the laboratory, this laser has found biological applications such as deep-tissue multiphoton imaging and industrial applications cold micromachining. When operated in the chirped pulse amplification mode, they can be used to generate extremely high peak powers in the terawatt range, which finds use in nuclear fusion research.

References edit

  1. ^ Moulton, P. F. (1986). "Spectroscopic and laser characteristics of Ti:Al2O3". Journal of the Optical Society of America B. 3 (1): 125–133. Bibcode:1986JOSAB...3..125M. doi:10.1364/JOSAB.3.000125.
  2. ^ Steele, T.R.; Gerstenberger, D. C.; Drobshoff, A.; Wallace, R. W. (15 March 1991). "Broadly tunable high-power operation of an all-solid-state titanium-doped sapphire laser system". Optics Letters. 16 (6): 399–401. Bibcode:1991OptL...16..399S. doi:10.1364/OL.16.000399. PMID 19773946.
  3. ^ Withnall, R. (2005-01-01). "SPECTROSCOPY | Raman Spectroscopy". In Guenther, Robert D. (ed.). Encyclopedia of Modern Optics. Oxford: Elsevier. pp. 119–134. doi:10.1016/b0-12-369395-0/00960-x. ISBN 978-0-12-369395-2. Retrieved 2021-10-02.
  4. ^ Erny, Christian; Hauri, Christoph P. (2013). "Design of efficient single stage chirped pulse difference frequency generation at 7 μm driven by a dual wavelength Ti:sapphire laser". Applied Physics B. 117 (1): 379–387. arXiv:1311.0610. Bibcode:2014ApPhB.117..379E. doi:10.1007/s00340-014-5846-6. S2CID 119237744.
  5. ^ Spence, D. E.; Kean, P. N.; Sibbett, W. (1991-01-01). "60-fsec pulse generation from a self-mode-locked Ti:sapphire laser". Optics Letters. 16 (1): 42–44. Bibcode:1991OptL...16...42S. CiteSeerX 10.1.1.463.8656. doi:10.1364/OL.16.000042. ISSN 1539-4794. PMID 19773831.
  6. ^ Strickland, Donna; Mourou, Gerard (1985-10-15). "Compression of amplified chirped optical pulses". Optics Communications. 55 (6): 447–449. Bibcode:1985OptCo..55..447S. doi:10.1016/0030-4018(85)90151-8.
  7. ^ "The Nobel Prize in Physics 2018". www.nobelprize.org. Retrieved 2018-10-02.
  8. ^ "Peter Moulton on the Ti:Sapphire laser. The Ti:sapphire laser has gained broad usage and new applications in biological research and other areas since its inception in 1982". spie.org. Retrieved 2017-11-02.
  9. ^ "Titanium–sapphire Lasers".
  10. ^ Hänsch, Theodor W. (2006). "Nobel Lecture: Passion for precision". Reviews of Modern Physics. 78 (4): 1297–1309. Bibcode:2006RvMP...78.1297H. doi:10.1103/RevModPhys.78.1297.
  11. ^ Hall, John L. (2006). "Nobel Lecture: Defining and measuring optical frequencies". Reviews of Modern Physics. 78 (4): 1279–1295. Bibcode:2006RvMP...78.1279H. doi:10.1103/RevModPhys.78.1279.
  12. ^ "The Nobel Prize in Physics 2005". www.nobelprize.org. Retrieved 2017-11-02.
  13. ^ Medeiros de Araújo, R. (2014). "Full characterization of a highly multimode entangled state embedded in an optical frequency comb using pulse shaping". Physical Review A. 89 (5): 053828. arXiv:1401.4867. Bibcode:2014PhRvA..89e3828M. doi:10.1103/PhysRevA.89.053828. S2CID 32829164.

External links edit

  • Encyclopedia of laser physics and technology on Ti:sapphire lasers

January 01, 1970
sapphire, laser, correct, title, this, article, sapphire, laser, substitution, colon, technical, restrictions, sapphire, lasers, also, known, al2o3, lasers, titanium, sapphire, lasers, sapphs, tunable, lasers, which, emit, near, infrared, light, range, from, 1. The correct title of this article is Ti sapphire laser The substitution of the colon is due to technical restrictions Ti sapphire lasers also known as Ti Al2O3 lasers titanium sapphire lasers or Ti sapphs are tunable lasers which emit red and near infrared light in the range from 650 to 1100 nanometers These lasers are mainly used in scientific research because of their tunability and their ability to generate ultrashort pulses thanks to its broad light emission spectrum Lasers based on Ti sapphire were first constructed and invented in June 1982 by Peter Moulton at the MIT Lincoln Laboratory 1 Part of a Ti sapphire oscillator The Ti sapphire crystal is the bright red light source on the left The green light is from the pump diode Titanium sapphire refers to the lasing medium a crystal of sapphire Al2O3 that is doped with Ti3 ions A Ti sapphire laser is usually pumped with another laser with a wavelength of 514 to 532 nm for which argon ion lasers 514 5 nm and frequency doubled Nd YAG Nd YLF and Nd YVO lasers 527 532 nm are used They are capable of laser operation from 670 nm to 1 100 nm wavelength 2 Ti sapphire lasers operate most efficiently at wavelengths near 800 nm 3 Contents 1 Types 1 1 Mode locked oscillators 1 2 Chirped pulse amplifiers 1 3 Tunable continuous wave lasers 2 History and applications 3 References 4 External linksTypes edit nbsp The inner optical setup of a femtosecond Ti sapphire pulsed laser Mode locked oscillators edit Mode locked oscillators generate ultrashort pulses with a typical duration between a few picoseconds and 10 femtoseconds in special cases even around 5 femtoseconds few carrier wave cycles in each laser pulses The pulse repetition frequency is in most cases around 70 to 90 MHz as given by the oscillator s round trip optical path typically a few meters Ti sapphire oscillators are normally pumped with a continuous wave laser beam from an argon or frequency doubled Nd YVO4 laser Typically such an oscillator has an average output power of 0 4 to 2 5 watts 5 7 to 35 nJ in each laser pulse for the 70 MHz repetition rate Chirped pulse amplifiers edit Main article Chirped pulse amplification These devices generate ultrashort ultra high intensity pulses with a duration of 20 to 100 femtoseconds A typical one stage amplifier can produce pulses of up to 5 millijoules in energy at a repetition frequency of 1000 hertz while a larger multistage facility can produce pulses up to several joules with a repetition rate of up to 10 Hz Usually amplifier crystals are pumped with a pulsed frequency doubled Nd YLF laser at 527 nm and operate at 800 nm Two different designs exist for the amplifier regenerative amplifier and multi pass amplifier Regenerative amplifiers operate by amplifying single pulses from an oscillator see above Instead of a normal cavity with a partially reflective mirror they contain high speed optical switches that insert a pulse into a cavity and take the pulse out of the cavity exactly at the right moment when it has been amplified to a high intensity The term chirped pulse refers to a special construction that is necessary to prevent the pulse from damaging the components in the laser The pulse is stretched in time so that the energy is not all located at the same point in time and space This prevents damage to the optics in the amplifier Then the pulse is optically amplified and recompressed in time to form a short localized pulse All optics after this point should be chosen to take the high energy density into consideration In a multi pass amplifier there are no optical switches Instead mirrors guide the beam a fixed number of times two or more through the Ti sapphire crystal with slightly different directions A pulsed pump beam can also be multi passed through the crystal so that more and more passes pump the crystal First the pump beam pumps a spot in the gain medium Then the signal beam first passes through the center for maximal amplification but in later passes the diameter is increased to stay below the damage threshold to avoid amplification the outer parts of the beam thus increasing beam quality and cutting off some amplified spontaneous emission and to completely deplete the inversion in the gain medium nbsp A Ti Sapphire crystal in the centre of a multipass amplifier Quantronix Odin is pumped by 5W green beam faintly visible coming from right amplifies femtosecond pulses that pass it several times under different angles invisible on the photo and loses part of energy as red fluorescence light The pulses from chirped pulse amplifiers are often converted to other wavelengths by means of various nonlinear optical processes At 5 mJ in 100 femtoseconds the peak power of such a laser is 50 gigawatts 4 When focused by a lens these laser pulses will ionise any material placed in the focus including air molecules and lead to short filament propagation and strong nonlinear optics effects that generate a wide spectrum of wavelengths nbsp Femtosecond pulses generate multiple angle resolved colour patterns when focused note their fan out angle is even higher than that of the focused laser beam Tunable continuous wave lasers edit Titanium sapphire is especially suitable for pulsed lasers since an ultrashort pulse inherently contains a wide spectrum of frequency components This is due to the inverse relationship between the frequency bandwidth of a pulse and its time duration due to their being conjugate variables However with an appropriate design titanium sapphire can also be used in continuous wave lasers with extremely narrow linewidths tunable over a wide range History and applications edit nbsp CW single frequency ring Ti Sapphire laser in operation at Novosibirsk State University The Ti sapphire laser was invented by Peter Moulton in June 1982 at MIT Lincoln Laboratory in its continuous wave version Subsequently these lasers were shown to generate ultrashort pulses through Kerr lens modelocking 5 Strickland and Mourou in addition to others working at the University of Rochester showed chirped pulse amplification of this laser within a few years 6 for which these two shared in the 2018 Nobel Prize in physics 7 along with Arthur Ashkin for optical tweezers The cumulative product sales of the Ti sapphire laser has amounted to more than 600 million making it a big commercial success that has sustained the solid state laser industry for more than three decades 8 9 The ultrashort pulses generated by Ti sapphire lasers in the time domain corresponds to mode locked optical frequency combs in the spectral domain Both the temporal and spectral properties of these lasers make them highly desirable for frequency metrology spectroscopy or for pumping nonlinear optical processes One half of the Nobel prize for physics in 2005 was awarded to the development of the optical frequency comb technique which heavily relied on the Ti sapphire laser and its self modelocking properties 10 11 12 The continuous wave versions of these lasers can be designed to have nearly quantum limited performance resulting in a low noise and a narrow linewidth making them attractive for quantum optics experiments 13 The reduced amplified spontaneous emission noise in the radiation of Ti sapphire lasers lends great strength in their application as optical lattices for the operation of state of the art atomic clocks Apart from fundamental science applications in the laboratory this laser has found biological applications such as deep tissue multiphoton imaging and industrial applications cold micromachining When operated in the chirped pulse amplification mode they can be used to generate extremely high peak powers in the terawatt range which finds use in nuclear fusion research References edit Moulton P F 1986 Spectroscopic and laser characteristics of Ti Al2O3 Journal of the Optical Society of America B 3 1 125 133 Bibcode 1986JOSAB 3 125M doi 10 1364 JOSAB 3 000125 Steele T R Gerstenberger D C Drobshoff A Wallace R W 15 March 1991 Broadly tunable high power operation of an all solid state titanium doped sapphire laser system Optics Letters 16 6 399 401 Bibcode 1991OptL 16 399S doi 10 1364 OL 16 000399 PMID 19773946 Withnall R 2005 01 01 SPECTROSCOPY Raman Spectroscopy In Guenther Robert D ed Encyclopedia of Modern Optics Oxford Elsevier pp 119 134 doi 10 1016 b0 12 369395 0 00960 x ISBN 978 0 12 369395 2 Retrieved 2021 10 02 Erny Christian Hauri Christoph P 2013 Design of efficient single stage chirped pulse difference frequency generation at 7 mm driven by a dual wavelength Ti sapphire laser Applied Physics B 117 1 379 387 arXiv 1311 0610 Bibcode 2014ApPhB 117 379E doi 10 1007 s00340 014 5846 6 S2CID 119237744 Spence D E Kean P N Sibbett W 1991 01 01 60 fsec pulse generation from a self mode locked Ti sapphire laser Optics Letters 16 1 42 44 Bibcode 1991OptL 16 42S CiteSeerX 10 1 1 463 8656 doi 10 1364 OL 16 000042 ISSN 1539 4794 PMID 19773831 Strickland Donna Mourou Gerard 1985 10 15 Compression of amplified chirped optical pulses Optics Communications 55 6 447 449 Bibcode 1985OptCo 55 447S doi 10 1016 0030 4018 85 90151 8 The Nobel Prize in Physics 2018 www nobelprize org Retrieved 2018 10 02 Peter Moulton on the Ti Sapphire laser The Ti sapphire laser has gained broad usage and new applications in biological research and other areas since its inception in 1982 spie org Retrieved 2017 11 02 Titanium sapphire Lasers Hansch Theodor W 2006 Nobel Lecture Passion for precision Reviews of Modern Physics 78 4 1297 1309 Bibcode 2006RvMP 78 1297H doi 10 1103 RevModPhys 78 1297 Hall John L 2006 Nobel Lecture Defining and measuring optical frequencies Reviews of Modern Physics 78 4 1279 1295 Bibcode 2006RvMP 78 1279H doi 10 1103 RevModPhys 78 1279 The Nobel Prize in Physics 2005 www nobelprize org Retrieved 2017 11 02 Medeiros de Araujo R 2014 Full characterization of a highly multimode entangled state embedded in an optical frequency comb using pulse shaping Physical Review A 89 5 053828 arXiv 1401 4867 Bibcode 2014PhRvA 89e3828M doi 10 1103 PhysRevA 89 053828 S2CID 32829164 External links editEncyclopedia of laser physics and technology on Ti sapphire lasers Retrieved from https en wikipedia org w index php title Ti sapphire laser amp oldid 1214217634, wikipedia, wiki, book, books, library,

article

, read, download, free, free download, mp3, video, mp4, 3gp, jpg, jpeg, gif, png, picture, music, song, movie, book, game, games.